lkml.org 
[lkml]   [2007]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: broken suspend [Was: 2.6.24-rc2-mm1]
On 11/16/2007 05:10 PM, Alan Stern wrote:
> On Thu, 15 Nov 2007, Greg KH wrote:
>
>>> The offending -mm patch is
>>> gregkh-driver-pm-acquire-device-locks-prior-to-suspending.patch
>>>
>>> 2.6.24-rc2-mm1 minus it works just fine; PROVE_LOCKING shows nothing new when
>>> the patch is applied.
>> Thanks for tracking this down. Alan, any thoughts?
>
> It's a driver problem somewhere. Probably not one of the most common
> drivers because I don't see the same problem here (but then I'm not
> testing -mm).
>
> The thing to do is figure out which driver is causing the problem.
> Jiri, try enabling CONFIG_DEBUG_DRIVER.

Sadly no output.

> If there's also a config
> option to prevent the console from being suspended, set it as well.

no_suspend_console kernel parameter has no effect (why?).

> Then you should be able to tell which driver is making trouble.

I think no unusual hardware inside:

00:00.0 Host bridge: Intel Corporation 82G33/G31/P35 Express DRAM Controller
(rev 02)
Subsystem: Intel Corporation 82G33/G31/P35 Express DRAM Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 c0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c0 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corporation 82G33/G31 Express Integrated Graphics
Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at ff900000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 c2 29 07 00 90 00 02 00 00 03 00 00 00 00
10: 00 00 a8 ff 01 ec 00 00 08 00 00 d0 00 00 90 ff
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c2 29
30: 00 00 00 00 90 00 00 00 00 00 00 00 0a 01 00 00

00:03.0 Communication controller: Intel Corporation 82G33/G31/P35 Express MEI
Controller (rev 02)
Subsystem: Intel Corporation 82G33/G31/P35 Express MEI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ffa7bc00 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c4 29 06 00 10 00 02 00 80 07 00 00 80 00
10: 04 bc a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c4 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:03.2 IDE interface: Intel Corporation 82G33/G31/P35 Express PT IDER
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation 82G33/G31/P35 Express PT IDER Controller
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 12
Region 0: I/O ports at e880 [size=8]
Region 1: I/O ports at e800 [size=4]
Region 2: I/O ports at e480 [size=8]
Region 3: I/O ports at e400 [size=4]
Region 4: I/O ports at e080 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c6 29 05 00 b0 00 02 85 01 01 00 00 00 00
10: 81 e8 00 00 01 e8 00 00 81 e4 00 00 01 e4 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 86 80 c6 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0c 03 00 00

00:03.3 Serial controller: Intel Corporation 82G33/G31/P35 Express Serial KT
Controller (rev 02) (prog-if 02 [16550])
Subsystem: Intel Corporation 82G33/G31/P35 Express Serial KT Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at e000 [size=8]
Region 1: Memory at ffa7a000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 c7 29 07 00 b0 00 02 02 00 07 00 00 00 00
10: 01 e0 00 00 00 a0 a7 ff 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 c7 29
30: 00 00 00 00 c8 00 00 00 00 00 00 00 05 02 00 00

00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network
Connection (rev 02)
Subsystem: Intel Corporation Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 318
Region 0: Memory at ffa40000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at ffa79000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at dc00 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
Address: 00000000fee0300c Data: 4191
Capabilities: [e0] Vendor Specific Information
00: 86 80 bd 10 07 04 10 00 02 00 00 02 00 00 00 00
10: 00 00 a4 ff 00 90 a7 ff 01 dc 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 00 00
30: 00 00 00 00 c8 00 00 00 00 00 00 00 0f 01 00 00

00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at d880 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 37 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 86 80 37 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 38 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 86 80 38 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 02 00 00

00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d480 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 39 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d4 00 00 00 00 00 00 00 00 00 00 86 80 39 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00

00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at ffa7b400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00: 86 80 3c 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b4 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3c 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 04 00 00

00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller
(rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) HD Audio Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffa70000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
00: 86 80 3e 29 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 00 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3e 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00

00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 34 29 05 00 90 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d4 00 00 00 00 00 00 00 00 00 00 86 80 34 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d080 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 35 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d0 00 00 00 00 00 00 00 00 00 00 86 80 35 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 02 00 00

00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d000 [size=32]
Capabilities: [50] Vendor Specific Information
00: 86 80 36 29 05 00 90 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 86 80 36 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 04 00 00

00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ffa7b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
Capabilities: [98] Vendor Specific Information
00: 86 80 3a 29 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 b0 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 3a 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) (prog-if 01
[Subtractive decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: ff600000-ff6fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge
00: 86 80 4e 24 06 01 10 00 92 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22
20: 60 ff 60 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00

00:1f.0 ISA bridge: Intel Corporation Unknown device 2910 (rev 02)
Subsystem: Intel Corporation Unknown device 2910
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 10 29 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 29
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port
SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA
AHCI Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 319
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c880 [size=4]
Region 2: I/O ports at c800 [size=8]
Region 3: I/O ports at c480 [size=4]
Region 4: I/O ports at c400 [size=32]
Region 5: Memory at ffa78800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4
Enable+
Address: fee0300c Data: 4169
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
Capabilities: [b0] Vendor Specific Information
00: 86 80 22 29 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 cc 00 00 81 c8 00 00 01 c8 00 00 81 c4 00 00
20: 01 c4 00 00 00 88 a7 ff 00 00 00 00 86 80 22 29
30: 00 00 00 00 80 00 00 00 00 00 00 00 03 02 00 00

00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) SMBus Controller
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ffa7b800 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00: 86 80 30 29 03 00 80 02 02 00 05 0c 00 00 00 00
10: 04 b8 a7 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 86 80 30 29
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 03 00 00

00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at b880 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at b480 [size=16]
Region 5: I/O ports at b400 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information
00: 86 80 26 29 07 00 b0 02 02 85 01 01 00 00 00 00
10: 01 c0 00 00 01 bc 00 00 81 b8 00 00 01 b8 00 00
20: 81 b4 00 00 01 b4 00 00 00 00 00 00 86 80 26 29
30: 00 00 00 00 70 00 00 00 00 00 00 00 03 02 00 00

00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family)
Thermal Subsystem (rev 02)
Subsystem: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 12
Region 0: Memory at ffa6f000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 32 29 02 00 10 00 02 00 80 11 00 00 00 00
10: 04 f0 a6 ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 32 29
30: 00 00 00 00 50 00 00 00 00 00 00 00 0c 03 00 00

01:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC
(rev 01)
Subsystem: Wistron NeWeb Corp. CM9 Wireless a/b/g MiniPCI Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ff6f0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00: 8c 16 13 00 16 00 90 02 01 00 00 02 08 a8 00 00
10: 00 00 6f ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 50 00 00 5f 18 12 10
30: 00 00 00 00 44 00 00 00 00 00 00 00 0e 01 0a 1c






Plugged usb devices:

Bus 004 Device 007: ID 045e:00f0 Microsoft Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x045e Microsoft Corp.
idProduct 0x00f0
bcdDevice 1.01
iManufacturer 1 Microsoft Corporation
iProduct 2 Microsoft � Laser Mouse 6000
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 33 US
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 59
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 10

Bus 004 Device 006: ID 0458:004c KYE Systems Corp. (Mouse Systems) Slimstar Pro
Keyboard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0458 KYE Systems Corp. (Mouse Systems)
idProduct 0x004c Slimstar Pro Keyboard
bcdDevice 1.01
iManufacturer 1 ABBHOME
iProduct 2 USB Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 59
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 50mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 1 Keyboard
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 65
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Devices
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 104
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10

Bus 004 Device 005: ID 04b4:2050 Cypress Semiconductor Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 8
idVendor 0x04b4 Cypress Semiconductor Corp.
idProduct 0x2050
bcdDevice 0.01
iManufacturer 1 Bella Corporation
iProduct 2 GBella Corporation DV Keyboard
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x000d
Per-port power switching
Compound device
Per-port overcurrent protection
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 25 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0x60
Hub Port Status:
Port 1: 0000.0103 power enable connect
Port 2: 0000.0303 lowspeed power enable connect
Port 3: 0000.0100 power

regards,
--
Jiri Slaby (jirislaby@gmail.com)
Faculty of Informatics, Masaryk University
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2007-11-17 16:11    [W:0.546 / U:0.648 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site