lkml.org 
[lkml]   [2007]   [Nov]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectSC1200 failure in 2.6.23 and 2.6.24-rc1-git10
    Date
    Finally i got full DMESG with 1GB card till end. Seems not readable too.

    Linux version 2.6.24-rc1-git10-embedded (root@homecore.visp.net.lb) (gcc
    version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 Thu Nov 1 23:12:53 EET 2007
    BIOS-provided physical RAM map:
    BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
    BIOS-e801: 0000000000100000 - 0000000004000000 (usable)
    64MB LOWMEM available.
    Zone PFN ranges:
    DMA 0 -> 4096
    Normal 4096 -> 16384
    Movable zone start PFN for each node
    early_node_map[1] active PFN ranges
    0: 0 -> 16384
    DMI not present or invalid.
    Allocating PCI resources starting at 10000000 (gap: 04000000:fc000000)
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
    Kernel command line: console=ttyS0,38400n8
    Initializing CPU#0
    PID hash table entries: 256 (order: 8, 1024 bytes)
    Detected 266.627 MHz processor.
    Console: colour dummy device 80x25
    console [ttyS0] enabled
    Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Memory: 62836k/65536k available (1020k kernel code, 2292k reserved, 317k
    data, 112k init, 0k highmem)
    virtual kernel memory layout:
    fixmap : 0xffffb000 - 0xfffff000 ( 16 kB)
    vmalloc : 0xc4800000 - 0xffff9000 ( 951 MB)
    lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
    .init : 0xc0252000 - 0xc026e000 ( 112 kB)
    .data : 0xc01ff111 - 0xc024e6f4 ( 317 kB)
    .text : 0xc0100000 - 0xc01ff111 (1020 kB)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
    Calibrating delay using timer specific routine.. 534.41 BogoMIPS (lpj=1068836)
    Mount-cache hash table entries: 512
    Compat vDSO mapped to ffffe000.
    CPU: NSC Unknown stepping 01
    Checking 'hlt' instruction... OK.
    Freeing SMP alternatives: 0k freed
    net_namespace: 64 bytes
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xfc3ad, last bus=0
    PCI: Using configuration type 1
    Setting up standard PCI resources
    SCSI subsystem initialized
    PCI: Probing PCI hardware
    PCI: Device 0000:00:12.5 not found by BIOS
    Time: tsc clocksource has been installed.
    NET: Registered protocol family 2
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    TCP reno registered
    scx200: NatSemi SCx200 Driver
    scx200: GPIO base 0xf400
    scx200: Configuration Block base 0x9000
    io scheduler noop registered (default)
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
    natsemi dp8381x driver, version 2.1, Sept 11, 2006
    originally by Donald Becker <becker@scyld.com>
    2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
    natsemi eth0: NatSemi DP8381[56] at 0x80000000 (0000:00:0e.0),
    00:0d:b9:00:8a:30, IRQ 10, port TP.
    scsi0 : sc1200
    scsi1 : sc1200
    ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
    ata2: DUMMY
    ata1.00: CFA: SanDisk SDCFH-1024, HDX 3.07, max MWDMA2
    ata1.00: 2001888 sectors, multi 0: LBA
    ata1.00: configured for MWDMA2
    scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFH-10 HDX PQ: 0 ANSI: 5
    sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
    DPO or FUA
    sd 0:0:0:0: [sda] 2001888 512-byte hardware sectors (1025 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
    DPO or FUA
    sda:<4>Clocksource tsc unstable (delta = -334501841 ns)
    Time: pit clocksource has been installed.
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA2
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA2
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA2
    ata1: EH complete
    ata1.00: limiting speed to MWDMA1:PIO4
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
    sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
    Descriptor sense data with sense descriptors (in hex):
    72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    00 00 00 00
    sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
    end_request: I/O error, dev sda, sector 0
    Buffer I/O error on device sda, logical block 0
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    ata1: EH complete
    ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
    ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    ata1.00: status: { DRDY }
    ata1: soft resetting link
    ata1.00: configured for MWDMA1
    sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
    sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
    Descriptor sense data with sense descriptors (in hex):
    72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    00 00 00 00
    sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
    end_request: I/O error, dev sda, sector 0
    Buffer I/O error on device sda, logical block 0
    ata1: EH complete
    unable to read partition table
    sd 0:0:0:0: [sda] Attached SCSI removable disk
    scx200_wdt: timer margin 60 seconds
    cpuidle: using governor ladder
    enabling scx200 high-res timer (1 MHz +0 ppm)
    TCP cubic registered
    Time: scx200_hrt clocksource has been installed.
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI Shortcut mode
    VFS: Cannot open root device "<NULL>" or unknown-block(8,18)
    Please append a correct "root=" boot option; here are the available
    partitions:
    0800 1000944 sda driver: sd
    Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-
    block(8,18)



    --
    Denys Fedoryshchenko
    Technical Manager
    Virtual ISP S.A.L.

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2007-11-01 23:07    [W:0.033 / U:91.716 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site