Messages in this thread | | | From | poison <> | Subject | Re: linux-2.6.23 - acting funny | Date | Fri, 12 Oct 2007 00:53:19 +0200 |
| |
Hi =)
On Thursday 11 October 2007, Helmut Toplizer wrote: > Hi! > > I had similar behavior in the kernel releases since I can think of. It doesn't happen before 2.6.23.
> (You may find some reports about at > http://marc.info/?a=113508574400006&r=1&w=2) > > Maybe your problem is similar. > > Here's what have been found out: > Plugin of ehci devices causes some strange DMA thing > which causes delays because of the CPU HLT instruction. > (DMA are handled with delays on HLT) > > Possible fixes: > 1) Kernel parameter: idle=poll > Disables HLT and causes heat up and noise from the cpu $ cat /proc/cmdline root=/dev/sdb1 ro vga=794 idle=poll
Same story. If I start: $ while true; do echo test > /dev/null; done ... the transfer rate goes up.
> > 2) Don't insert EHCI-USB devices Still reproducable with all USB devices except keyboard+mouse removed, ehci deselcted in kernel config and booting with idle=poll.
> > 3) Patch: attached, try out at your own risk. > you need to add a kernel-boot parameter "disableviahlt" > (You've got a via-chipset, right?) > > Please report back to me if 1/2 works or to linux-ide if the patch works. No VIA chip in sight. Mainboard is an Intel 975XBX2 and hard disks are connected to the ICH7 SATA Controller, so I don't think the patch will help me ^^ lspci attached.
Also the transfer rate didn't degrade too much for copying directly from reiserfs to reiserfs and not using encfs:
dd if=/mnt/.backup/2CpGkrxvz6wgA0b0xloz8PavzMLrMymOgi9 of=/mnt/.tdata/test 1033+0 records in 1033+0 records out 1083179008 bytes (1.1 GB) copied, 16.9303 s, 64.0 MB/s
Plus the transfer rate doesn't increase if I start a CPU hog while copying between reiserfs.
So it looks more to me like theres a bad interaction between the new scheduler, fuse and encfs ...
> Thanks > > Helmut
Thanks for your reply ^^ 00:00.0 Host bridge: Intel Corporation 82975X Memory Controller Hub Subsystem: Intel Corporation Unknown device 5842 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 0 Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation 82975X PCI Express Root Port (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: e0000000-e1ffffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- Capabilities: [88] Subsystem: Intel Corporation Unknown device 5842 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 41b9 Capabilities: [a0] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2 Link: Latency L0s <256ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 0, PowerLimit 75.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME-
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01) Subsystem: Intel Corporation Unknown device 0419 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 21 Region 0: Memory at e2200000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [70] Express Unknown type IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <64ns, L1 <1us Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0 Link: Latency L0s <64ns, L1 <1us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed unknown, Width x0
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s unlimited, L1 unlimited Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1 Link: Latency L0s <1us, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x0 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 1, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 41c1 Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: e2100000-e21fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [40] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s unlimited, L1 unlimited Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6 Link: Latency L0s <256ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x1 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+ Slot: Number 6, PowerLimit 10.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Unknown, PwrInd Unknown, Power- Root: Correctable- Non-Fatal- Fatal- PME- Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 41c9 Capabilities: [90] Subsystem: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at 4080 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 4060 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 4040 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at 4020 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at e2204400 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=32 I/O behind bridge: 00001000-00001fff Memory behind bridge: e2000000-e20fffff Prefetchable memory behind bridge: 00000000e2300000-00000000e23fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [50] Subsystem: Intel Corporation Unknown device 5842
00:1f.0 ISA bridge: Intel Corporation 82801GH (ICH7DH) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [e0] Vendor Specific Information
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 40b0 [size=16]
00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 220 Region 0: I/O ports at 40c8 [size=8] Region 1: I/O ports at 40e4 [size=4] Region 2: I/O ports at 40c0 [size=8] Region 3: I/O ports at 40e0 [size=4] Region 4: I/O ports at 40a0 [size=16] Region 5: Memory at e2204000 (32-bit, non-prefetchable) [size=1K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Address: fee0300c Data: 41e1 Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation Unknown device 5842 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 4000 [size=32]
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7900 GT/GTO] (rev a1) (prog-if 00 [VGA]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e1000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at e0000000 (64-bit, non-prefetchable) [size=16M] Region 5: I/O ports at 3000 [size=128] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express Endpoint IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <256ns, L1 <4us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0 Link: Latency L0s <256ns, L1 <4us Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x16
03:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Intel Corporation Unknown device 30a5 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 219 Region 0: Memory at e2100000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Address: 00000000fee0300c Data: 4142 Capabilities: [e0] Express Endpoint IRQ 0 Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <64us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0 Link: Latency L0s <128ns, L1 <64us Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch- Link: Speed 2.5Gb/s, Width x1
04:00.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04) Subsystem: Creative Labs SB Audigy 2 ZS (SB0350) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 1000 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:00.1 Input device controller: Creative Labs SB Audigy Game Port (rev 04) Subsystem: Creative Labs SB Audigy MIDI/Game Port Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at 1060 [size=8] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
04:00.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04) (prog-if 10 [OHCI]) Subsystem: Creative Labs SB Audigy FireWire Port Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 21 Region 0: Memory at e2008800 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e2004000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+
04:02.0 RAID bus controller: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host Controller (rev 02) Subsystem: Silicon Image, Inc. Winic W-680 (Silicon Image 680 based) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 1058 [size=8] Region 1: I/O ports at 106c [size=4] Region 2: I/O ports at 1050 [size=8] Region 3: I/O ports at 1068 [size=4] Region 4: I/O ports at 1040 [size=16] Region 5: Memory at e2009000 (32-bit, non-prefetchable) [size=256] Expansion ROM at e2300000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
04:04.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) Subsystem: Intel Corporation Unknown device 5842 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at e2008000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at e2000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+
| |