lkml.org 
[lkml]   [2007]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject[2.6.20-rc5]KVM - Win98SE won't install
Hardware list attached, and config. When scanning disk at the start of 
the install, exits with "signal 13 (0)" and no log entry. Just as the
kvm dies there's a switch from the blue install screen to a white on
black screen, and a message displays for a fraction of a sec, unreadably
fast.

I dount it's hardware, memtest was recently run 12hr, and installs of
DragonFlyBSD and FreeBSD work.

I have two patches applied, diff also attached.

Running qemu user mode works, running xen-install does exactly the sdame
thing. Obviously I would rather run kvm.

Any other info needed, or things to try, let me know. I did run with -d,
nothing written in qemu.log.

--
Bill Davidsen
He was a full-time professional cat, not some moonlighting
ferret or weasel. He knew about these things.
Linux version 2.6.20-rc5 (davidsen@posidon.tmr.com) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #3 SMP Sun Jan 14 11:33:19 EST 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000e4000 size: 000000000001c000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000007f6a0000 end: 000000007f7a0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000007f7a0000 size: 000000000000e000 end: 000000007f7ae000 type: 3
copy_e820_map() start: 000000007f7ae000 size: 0000000000032000 end: 000000007f7e0000 type: 4
copy_e820_map() start: 000000007f7e0000 size: 0000000000020000 end: 000000007f800000 type: 2
copy_e820_map() start: 00000000ffb80000 size: 0000000000480000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f7a0000 (usable)
BIOS-e820: 000000007f7a0000 - 000000007f7ae000 (ACPI data)
BIOS-e820: 000000007f7ae000 - 000000007f7e0000 (ACPI NVS)
BIOS-e820: 000000007f7e0000 - 000000007f800000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
1143MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 522144) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 522144
early_node_map[1] active PFN ranges
0: 0 -> 522144
On node 0 totalpages: 522144
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 2287 pages used for memmap
HighMem zone: 290481 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x000fa5d0
ACPI: XSDT (v001 A M I OEMXSDT 0x10000627 MSFT 0x00000097) @ 0x7f7a0100
ACPI: FADT (v003 A M I OEMFACP 0x10000627 MSFT 0x00000097) @ 0x7f7a0290
ACPI: MADT (v001 A M I OEMAPIC 0x10000627 MSFT 0x00000097) @ 0x7f7a0390
ACPI: OEMB (v001 A M I AMI_OEM 0x10000627 MSFT 0x00000097) @ 0x7f7ae040
ACPI: MCFG (v001 A M I OEMMCFG 0x10000627 MSFT 0x00000097) @ 0x7f7a4f00
ACPI: DSDT (v001 A0281 A0281074 0x00000074 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7f800000:80380000)
Detected 2394.060 MHz processor.
Built 1 zonelists. Total pages: 518065
Kernel command line: ro root=/dev/VG01/Root32 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2061272k/2088576k available (4101k kernel code, 26112k reserved, 1851k data, 324k init, 1171072k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc06d9000 - 0xc072a000 ( 324 kB)
.data : 0xc0501575 - 0xc06d032c (1851 kB)
.text : 0xc0100000 - 0xc0501575 (4101 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4789.80 BogoMIPS (lpj=2394904)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 18k freed
ACPI: Core revision 20060707
tbxface-0107 [01] load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:
Table [DSDT](id 0005) - 691 Objects with 54 Devices 195 Methods 25 Regions
ACPI Namespace successfully loaded at root c078a570
evxfevnt-0089 [02] enable : Transition to ACPI mode successful
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4787.21 BogoMIPS (lpj=2393605)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9577.01 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=80
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0951 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-1048 [03] ev_initialize_gpe_bloc: Found 11 Wake, Enabled 0 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:....................................................................................................................
Initialized 24/25 Regions 23/23 Fields 36/36 Buffers 33/34 Packages (700 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 0 _STA executions (examined 60 objects)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
libata version 2.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: e000-efff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: d000-dfff
MEM window: cff00000-cfffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: b000-cfff
MEM window: cfe00000-cfefffff
PREFETCH window: 80000000-800fffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1939k freed
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
audit: initializing netlink socket (disabled)
audit(1168792625.910:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/O].
SELinux: Registering netfilter hooks
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
Parsing all Control Methods:
Table [SSDT](id 00C5) - 10 Objects with 0 Devices 4 Methods 0 Regions
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ CPU1PM] [20060707]
ACPI: Processor [CPU1] (supports 8 throttling states)
Parsing all Control Methods:
Table [SSDT](id 00C7) - 10 Objects with 0 Devices 4 Methods 0 Regions
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ CPU2PM] [20060707]
ACPI: Processor [CPU2] (supports 8 throttling states)
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.6.0 20060119 on minor 0
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
intelfb: intelfb_init
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
intelfb: intelfb_setup
intelfb: no options
intelfb: intelfb_pci_register
intelfb: fb aperture: 0xd0000000/0x10000000, MMIO region: 0xcfd00000/0x80000
intelfb: 00:02.0: Intel(R) 945G, aperture size 256MB, stolen memory 7932kB
intelfb: fb: 0xd0000000(+ 0x0)/0x7bf000 (0xf8a00000)
intelfb: MMIO: 0xcfd00000/0x80000 (0xfc200000)
intelfb: ring buffer: 0xd3001000/0x10000 (0xfba01000)
intelfb: HW cursor: 0x0/0x0 (0x00000000) (offset 0x0) (phys 0x0)
intelfb: options: vram = 4, accel = 1, hwcursor = 0, fixed = 0, noinit = 0
intelfb: options: mode = ""
intelfb: intelfb_set_fbinfo
intelfb: intelfb_init_var
intelfb: intelfb_check_var: accel_flags is 0
intelfb: Mode is interlaced.
intelfb: intelfb_check_var: accel_flags is 0
intelfb: intelfb_var_to_depth: bpp: 32, green.length is 0
intelfb: intelfb_check_var: accel_flags is 0
intelfb: intelfb_var_to_depth: bpp: 32, green.length is 8
intelfb: Initial video mode is 1024x768-32@70.
intelfb: Initial video mode is from 1.
intelfb: update_dinfo
intelfb: intelfb_var_to_depth: bpp: 32, green.length is 8
intelfb: I2C bus CRTDDC_A registered.
intelfb: I2C bus SDVOCTRL_E registered.
intelfb: intelfbhw_print_hw_state
hw state dump start
VGA0_DIVISOR: 0x00031108
VGA1_DIVISOR: 0x00031406
VGAPD: 0x00020002
VGA0: (m1, m2, n, p1, p2) = (17, 8, 3, 2, 0)
VGA0: clock is 100800
VGA1: (m1, m2, n, p1, p2) = (20, 6, 3, 2, 0)
VGA1: clock is 113280
DPLL_A: 0x84800003
DPLL_B: 0x84800003
FPA0: 0x00031108
FPA1: 0x00031108
FPB0: 0x00031108
FPB1: 0x00031108
PLLA0: (m1, m2, n, p1, p2) = (17, 8, 3, 8, 0)
PLLA0: clock is 25200
PLLA1: (m1, m2, n, p1, p2) = (17, 8, 3, 8, 0)
PLLA1: clock is 25200
HTOTAL_A: 0x031f027f
HBLANK_A: 0x03170287
HSYNC_A: 0x02ef028f
VTOTAL_A: 0x020c01df
VBLANK_A: 0x020401e7
VSYNC_A: 0x01eb01e9
SRC_SIZE_A: 0x027f01df
BCLRPAT_A: 0x00000000
HTOTAL_B: 0x031f027f
HBLANK_B: 0x03170287
HSYNC_B: 0x02ef028f
VTOTAL_B: 0x020c01df
VBLANK_B: 0x020401e7
VSYNC_B: 0x01eb01e9
SRC_SIZE_B: 0x027f01df
BCLRPAT_B: 0x00000000
ADPA: 0x80008000
DVOA: 0x00000000
DVOB: 0x00480000
DVOC: 0x00480000
DVOA_SRCDIM: 0x00000000
DVOB_SRCDIM: 0x00000000
DVOC_SRCDIM: 0x00000000
LVDS: 0x00000000
PIPEACONF: 0x80000000
PIPEBCONF: 0x80000000
DISPARB: 0x00001d9c
CURSOR_A_CONTROL: 0x00000000
CURSOR_B_CONTROL: 0x00000000
CURSOR_A_BASEADDR: 0x00000000
CURSOR_B_BASEADDR: 0x00000000
CURSOR_A_PALETTE: 0x00000000, 0x00000000, 0x00000000, 0x00000000
CURSOR_B_PALETTE: 0x00000000, 0x00000000, 0x00000000, 0x00000000
CURSOR_SIZE: 0x00000000
DSPACNTR: 0x48000000
DSPBCNTR: 0x01000000
DSPABASE: 0x00000000
DSPBBASE: 0x00000000
DSPASTRIDE: 0x00000280
DSPBSTRIDE: 0x00000000
VGACNTRL: 0x0000008e
ADD_ID: 0x00000000
SWF00 0x00000000
SWF01 0x00000000
SWF02 0x00000000
SWF03 0x00000000
SWF04 0x00000000
SWF05 0x00000000
SWF06 0x00000000
SWF10 0x00000001
SWF11 0x00000000
SWF12 0x00000000
SWF13 0x03030000
SWF14 0xc0000000
SWF15 0x00000041
SWF16 0x00000000
SWF30 0x00000000
SWF31 0x00000000
SWF32 0x00000000
FENCE0 0x00000000
FENCE1 0x00000000
FENCE2 0x00000000
FENCE3 0x00000000
FENCE4 0x00000000
FENCE5 0x00000000
FENCE6 0x00000000
FENCE7 0x00000000
INSTPM 0x00000000
MEM_MODE 0x00000000
FW_BLC_0 0x03060106
FW_BLC_1 0x00000306
HWSTAM 0xffff
IER 0x0000
IIR 0x0000
IMR 0xffff
hw state dump end
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.3.15-k2
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:17:31:5c:57:c0
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: DVDRW DRW-3S163, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.001.
ata_piix 0000:00:1f.2: version 2.00ac7
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xA800 ctl 0xA402 bmdma 0x9400 irq 17
ata2: SATA max UDMA/133 cmd 0xA000 ctl 0x9802 bmdma 0x9408 irq 17
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.01: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata1.01: ata1: dev 1 multi count 16
ata1.00: configured for UDMA/133
ata1.01: configured for UDMA/133
scsi1 : ata_piix
ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 0:0:1:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 >
sd 0:0:1:0: Attached scsi disk sdb
sd 0:0:1:0: Attached scsi generic sg1 type 0
scsi 1:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 >
sd 1:0:0:0: Attached scsi disk sdc
sd 1:0:0:0: Attached scsi generic sg2 type 0
Fusion MPT base driver 3.04.02
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.02
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x00008000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 20, io base 0x00009000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
i2c /dev entries driver
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1 894 MB/s
raid6: int32x2 945 MB/s
raid6: int32x4 820 MB/s
raid6: int32x8 824 MB/s
raid6: mmxx1 3027 MB/s
raid6: mmxx2 3472 MB/s
raid6: sse1x1 1816 MB/s
raid6: sse1x2 2617 MB/s
raid6: sse2x1 3519 MB/s
raid6: sse2x2 4078 MB/s
raid6: using algorithm sse2x2 (4078 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 8640.000 MB/sec
raid5: using function: pIII_sse (8640.000 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
logips2pp: Detected unknown logitech mouse model 11
Intel 810 + AC97 Audio, version 1.01, 23:46:48 Jan 12 2007
Advanced Linux Sound Architecture Driver Version 1.0.14rc1 (Tue Jan 09 09:56:17 2007 UTC).
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
ALSA device list:
#0: HDA Intel at 0xcfdfc000 irq 20
TCP cubic registered
TCP highspeed registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 324k freed
Time: tsc clocksource has been installed.
md: Autodetecting RAID arrays.
md: invalid raid superblock magic on sda7
md: sda7 has invalid sb, not importing!
input: PS/2 Logitech Mouse as /class/input/input3
md: invalid raid superblock magic on sdb7
md: sdb7 has invalid sb, not importing!
md: invalid raid superblock magic on sdc7
md: sdc7 has invalid sb, not importing!
md: autorun ...
md: considering sdc6 ...
md: adding sdc6 ...
md: sdc5 has different UUID to sdc6
md: sdc3 has different UUID to sdc6
md: sdc2 has different UUID to sdc6
md: sdc1 has different UUID to sdc6
md: adding sdb6 ...
md: sdb5 has different UUID to sdc6
md: sdb3 has different UUID to sdc6
md: sdb2 has different UUID to sdc6
md: sdb1 has different UUID to sdc6
md: adding sda6 ...
md: sda5 has different UUID to sdc6
md: sda3 has different UUID to sdc6
md: sda2 has different UUID to sdc6
md: sda1 has different UUID to sdc6
md: created md4
md: bind<sda6>
md: bind<sdb6>
md: bind<sdc6>
md: running: <sdc6><sdb6><sda6>
raid1: raid set md4 active with 3 out of 3 mirrors
md: considering sdc5 ...
md: adding sdc5 ...
md: sdc3 has different UUID to sdc5
md: sdc2 has different UUID to sdc5
md: sdc1 has different UUID to sdc5
md: adding sdb5 ...
md: sdb3 has different UUID to sdc5
md: sdb2 has different UUID to sdc5
md: sdb1 has different UUID to sdc5
md: adding sda5 ...
md: sda3 has different UUID to sdc5
md: sda2 has different UUID to sdc5
md: sda1 has different UUID to sdc5
md: created md3
md: bind<sda5>
md: bind<sdb5>
md: bind<sdc5>
md: running: <sdc5><sdb5><sda5>
raid5: device sdc5 operational as raid disk 2
raid5: device sdb5 operational as raid disk 1
raid5: device sda5 operational as raid disk 0
raid5: allocated 3157kB for md3
raid5: raid level 5 set md3 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda5
disk 1, o:1, dev:sdb5
disk 2, o:1, dev:sdc5
md: considering sdc3 ...
md: adding sdc3 ...
md: sdc2 has different UUID to sdc3
md: sdc1 has different UUID to sdc3
md: adding sdb3 ...
md: sdb2 has different UUID to sdc3
md: sdb1 has different UUID to sdc3
md: adding sda3 ...
md: sda2 has different UUID to sdc3
md: sda1 has different UUID to sdc3
md: created md2
md: bind<sda3>
md: bind<sdb3>
md: bind<sdc3>
md: running: <sdc3><sdb3><sda3>
raid5: device sdc3 operational as raid disk 2
raid5: device sdb3 operational as raid disk 1
raid5: device sda3 operational as raid disk 0
raid5: allocated 3157kB for md2
raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda3
disk 1, o:1, dev:sdb3
disk 2, o:1, dev:sdc3
md: considering sdc2 ...
md: adding sdc2 ...
md: sdc1 has different UUID to sdc2
md: adding sdb2 ...
md: sdb1 has different UUID to sdc2
md: adding sda2 ...
md: sda1 has different UUID to sdc2
md: created md1
md: bind<sda2>
md: bind<sdb2>
md: bind<sdc2>
md: running: <sdc2><sdb2><sda2>
raid5: device sdc2 operational as raid disk 2
raid5: device sdb2 operational as raid disk 1
raid5: device sda2 operational as raid disk 0
raid5: allocated 3157kB for md1
raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda2
disk 1, o:1, dev:sdb2
disk 2, o:1, dev:sdc2
md: considering sdc1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: running: <sdc1><sdb1><sda1>
raid1: raid set md0 active with 3 out of 3 mirrors
md: ... autorun DONE.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1168792630.987:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1585 types, 172 bools, 1 sens, 1024 cats
security: 59 classes, 49500 rules
security: class dccp_socket not defined in policy
security: permission dccp_recv in class node not defined in policy
security: permission dccp_send in class node not defined in policy
security: permission dccp_recv in class netif not defined in policy
security: permission dccp_send in class netif not defined in policy
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1168792631.143:3): policy loaded auid=4294967295
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev md0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev dm-1, type ext3), uses xattr
Adding 2039800k swap on /dev/md1. Priority:-1 extents:1 across:2039800k
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.lo.base_reachable_time; Use net.ipv6.neigh.lo.base_reachable_time_ms instead.
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
eth0: no IPv6 routers present
kvm: msrs: 2
kvm: msrs: 2
[unhandled content-type:application/x-gzip]processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz
stepping : 6
cpu MHz : 1596.000
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 4789.81
clflush size : 64

processor : 1
vendor_id : GenuineIntel
cpu family : 6
model : 15
model name : Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz
stepping : 6
cpu MHz : 1596.000
cache size : 4096 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 10
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr lahf_lm
bogomips : 4787.23
clflush size : 64

\
 
 \ /
  Last update: 2007-01-14 21:03    [W:0.050 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site