lkml.org 
[lkml]   [2006]   [Jul]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject2.6.18-rc2 Intermittent failures to detect sata disks
Date
I am seeing an intermittent failures to detect sata disks on
2.6.18-rc2. Dell SC1425, PIIX chipset, gcc 4.1.0 (opensuse 10.1).
Sometimes it will detect both disks, sometimes only one, sometimes none
at all. AFAICT it only occurs after a soft reboot, and possibly only
after an emergency reboot. Alas the problem is so intermittent that it
is hard to tell what conditions will trigger it.

Setting ATA_DEBUG gives these differences:

works:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
piix_init: pci_module_init
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ata_pci_init_one: ENTER
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17
ata_device_add: ENTER
ata_host_add: ENTER
ata_port_start: prd alloc, virt f7b2e000, dma 37b2e000
ata1: SATA max UDMA/133 cmd 0xCCB8 ctl 0xCCB2 bmdma 0xCC80 irq 17
__ata_port_freeze: ata1 port frozen
ata_host_add: ENTER
ata_port_start: prd alloc, virt f7b1c000, dma 37b1c000
ata2: SATA max UDMA/133 cmd 0xCCA0 ctl 0xCC9A bmdma 0xCC88 irq 17
__ata_port_freeze: ata2 port frozen
ata_device_add: probe begin
scsi0 : ata_piix
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata1 port frozen
piix_sata_prereset: ata1: ENTER, pcs=0x33 base=0
piix_sata_prereset: ata1: LEAVE, pcs=0x33 present_mask=0x1
ata_std_softreset: ENTER
ata_std_softreset: about to softreset, devmask=1
ata_bus_softreset: ata1: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_std_softreset: EXIT, classes[0]=1 [1]=0
ata_std_postreset: ENTER
ata_std_postreset: EXIT
ata_eh_thaw_port: ata1 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_exec_command_pio: ata1: cmd 0xEC
ata_hsm_move: ata1: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_hsm_move: ata1: protocol 2 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata1.00: ATA-6, max UDMA/100, 156250000 sectors: LBA
ata1.00: ata1: dev 0 multi count 8
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_dev_set_xfermode: set features - xfer mode
ata_exec_command_pio: ata1: cmd 0xEF
ata_hsm_move: ata1: protocol 1 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_dev_set_xfermode: EXIT, err_mask=0
ata_exec_command_pio: ata1: cmd 0xEC
ata_hsm_move: ata1: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_hsm_move: ata1: protocol 2 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_dev_set_mode: xfer_shift=8, xfer_mode=0x45
ata1.00: configured for UDMA/100
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
scsi1 : ata_piix
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata2 port frozen
piix_sata_prereset: ata2: ENTER, pcs=0x33 base=2
piix_sata_prereset: ata2: LEAVE, pcs=0x33 present_mask=0x1
ata_std_softreset: ENTER
ata_std_softreset: about to softreset, devmask=1
ata_bus_softreset: ata2: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_std_softreset: EXIT, classes[0]=1 [1]=0
ata_std_postreset: ENTER
ata_std_postreset: EXIT
ata_eh_thaw_port: ata2 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_exec_command_pio: ata2: cmd 0xEC
ata_hsm_move: ata2: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_hsm_move: ata2: protocol 2 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata2.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 8

fails:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
hda: TEAC CD-ROM CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
piix_init: pci_module_init
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ata_pci_init_one: ENTER
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17
ata_device_add: ENTER
ata_host_add: ENTER
ata_port_start: prd alloc, virt f7879000, dma 37879000
ata1: SATA max UDMA/133 cmd 0xCCB8 ctl 0xCCB2 bmdma 0xCC80 irq 17
__ata_port_freeze: ata1 port frozen
ata_host_add: ENTER
ata_port_start: prd alloc, virt f787b000, dma 3787b000
ata2: SATA max UDMA/133 cmd 0xCCA0 ctl 0xCC9A bmdma 0xCC88 irq 17
__ata_port_freeze: ata2 port frozen
ata_device_add: probe begin
scsi0 : ata_piix
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata1 port frozen
piix_sata_prereset: ata1: ENTER, pcs=0x0 base=0
piix_sata_prereset: ata1: LEAVE, pcs=0x0 present_mask=0x0
ata1: SATA port has no device.
ata_eh_thaw_port: ata1 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
scsi1 : ata_piix
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_eh_autopsy: ENTER
ata_eh_recover: ENTER
ata_eh_prep_resume: ENTER
ata_eh_prep_resume: EXIT
__ata_port_freeze: ata2 port frozen
piix_sata_prereset: ata2: ENTER, pcs=0x33 base=2
piix_sata_prereset: ata2: LEAVE, pcs=0x33 present_mask=0x1
ata_std_softreset: ENTER
ata_std_softreset: about to softreset, devmask=1
ata_bus_softreset: ata2: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_std_softreset: EXIT, classes[0]=1 [1]=0
ata_std_postreset: ENTER
ata_std_postreset: EXIT
ata_eh_thaw_port: ata2 port thawed
ata_eh_revalidate_and_attach: ENTER
ata_exec_command_pio: ata2: cmd 0xEC
ata_hsm_move: ata2: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_hsm_move: ata2: protocol 2 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata2.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 8
ata_eh_revalidate_and_attach: EXIT
ata_eh_resume: ENTER
ata_eh_resume: EXIT
ata_dev_set_xfermode: set features - xfer mode
ata_exec_command_pio: ata2: cmd 0xEF
ata_hsm_move: ata2: protocol 1 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_dev_set_xfermode: EXIT, err_mask=0
ata_exec_command_pio: ata2: cmd 0xEC
ata_hsm_move: ata2: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_hsm_move: ata2: protocol 2 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_port_flush_task: ENTER
ata_port_flush_task: flush #1
ata_dev_set_mode: xfer_shift=8, xfer_mode=0x46
ata2.00: configured for UDMA/133
ata_eh_suspend: ENTER
ata_eh_suspend: EXIT
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_device_add: host probe begin
ata_scsi_dump_cdb: CDB (2:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsi_dump_cdb: CDB (2:0,0,0) 12 00 00 00 60 00 00 00 00
Vendor: ATA Model: ST3300622AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
piix_init: done
ata_scsi_dump_cdb: CDB (2:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsi_dump_cdb: CDB (2:0,0,0) 25 00 00 00 00 00 00 00 00
SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
ata_scsi_dump_cdb: CDB (2:0,0,0) 5a 00 3f 00 00 00 00 00 08
sda: Write Protect is off
ata_scsi_dump_cdb: CDB (2:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsi_dump_cdb: CDB (2:0,0,0) 5a 00 08 00 00 00 00 00 24
SCSI device sda: drive cache: write back
ata_scsi_dump_cdb: CDB (2:0,0,0) 00 00 00 00 00 00 00 00 24
ata_scsi_dump_cdb: CDB (2:0,0,0) 25 00 00 00 00 00 00 00 00
SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
ata_scsi_dump_cdb: CDB (2:0,0,0) 5a 00 3f 00 00 00 00 00 08
sda: Write Protect is off
ata_scsi_dump_cdb: CDB (2:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsi_dump_cdb: CDB (2:0,0,0) 5a 00 08 00 00 00 00 00 24
SCSI device sda: drive cache: write back
sda:<3>ata_scsi_dump_cdb: CDB (2:0,0,0) 28 00 00 00 00 00 00 00 08
ata_sg_setup: 1 sg elements mapped
ata_exec_command_pio: ata2: cmd 0xC8
ata_hsm_move: ata2: protocol 3 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
sda1 <<3>ata_scsi_dump_cdb: CDB (2:0,0,0) 28 00 00 00 00 38 00 00 08
ata_sg_setup: 1 sg elements mapped
ata_exec_command_pio: ata2: cmd 0xC8
ata_hsm_move: ata2: protocol 3 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
sda5<3>ata_scsi_dump_cdb: CDB (2:0,0,0) 28 00 00 0f 71 78 00 00 08
ata_sg_setup: 1 sg elements mapped
ata_exec_command_pio: ata2: cmd 0xC8
ata_hsm_move: ata2: protocol 3 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
sda6<3>ata_scsi_dump_cdb: CDB (2:0,0,0) 28 00 00 f4 a4 60 00 00 08
ata_sg_setup: 1 sg elements mapped
ata_exec_command_pio: ata2: cmd 0xC8
ata_hsm_move: ata2: protocol 3 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
sda7<3>ata_scsi_dump_cdb: CDB (2:0,0,0) 28 00 01 04 15 e0 00 00 08
ata_sg_setup: 1 sg elements mapped
ata_exec_command_pio: ata2: cmd 0xC8
ata_hsm_move: ata2: protocol 3 task_state 3 (dev_stat 0x50)
ata_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
sda8 >
sd 1:0:0:0: Attached scsi disk sda
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
S0 S4 S5)
VFS: Cannot open root device "sda10" or unknown-block(8,10)

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2006-07-21 08:21    [W:0.068 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site