Messages in this thread | | | Date | Thu, 22 Jun 2006 23:27:24 +0200 | From | Alessio Sangalli <> | Subject | Re: [PATCH] cardbus: revert IO window limit |
| |
Linus Torvalds wrote: > > On Thu, 22 Jun 2006, Andrew Morton wrote: >> OK, thanks. All we have on Alessio's machine is "freezes at boot if APM is enabled" >> (http://lkml.org/lkml/2006/6/16/33). Any suggestions as to how to proceed >> with that? > > It would be interesting to see the output of "/sbin/lspci -vvx" with a > working and a non-working kernel (obviously APM has to be disabled for > this test). > > And the full bootup dmesg for both cases (preferably with CONFIG_PCI_DEBUG > enabled) > > Alessio?
Ok I've found how to enable PCI_DEBUG (I had to enable kernel debugging first).
************************************************** "git clone" of the kernel repository compiled it without APM support: **************************************************
# /sbin/lspci -vvx 00:00.0 Host bridge: Intel Corp. 82440MX Host Bridge (rev 01) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 00: 86 80 94 71 06 00 00 22 01 00 00 06 00 40 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.1 Multimedia audio controller: Intel Corp. 82440MX AC'97 Audio Controller Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at 1600 [size=256] Region 1: I/O ports at 1500 [size=64] 00: 86 80 95 71 05 00 00 00 00 00 01 04 00 00 00 00 10: 01 16 00 00 01 15 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
00:00.2 Modem: Intel Corp. 82440MX AC'97 Modem Controller (prog-if 00 [Generic]) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at 1800 [size=256] Region 1: I/O ports at 1700 [size=128] 00: 86 80 96 71 05 00 00 00 00 00 03 07 00 00 00 00 10: 01 18 00 00 01 17 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
00:07.0 ISA bridge: Intel Corp. 82440MX ISA Bridge (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 86 80 98 71 0f 00 80 02 01 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corp. 82440MX EIDE Controller (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 1100 [size=16] 00: 86 80 99 71 05 00 80 02 00 80 01 01 00 40 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corp. 82440MX USB Universal Host Controller (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 240 Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at 1200 [size=32] 00: 86 80 9a 71 05 00 80 02 00 00 03 0c 00 f0 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:07.3 Bridge: Intel Corp. 82440MX Power Management Controller Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00: 86 80 9b 71 01 00 80 02 00 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 24020000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=01, subordinate=04, sec-latency=176 Memory window 0: 20000000-21fff000 (prefetchable) Memory window 1: 22000000-23fff000 I/O window 0: 00001000-000010ff I/O window 1: 00001400-000014ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00: 4c 10 50 ac 07 00 10 02 01 00 07 06 08 a8 02 00 10: 00 00 02 24 a0 00 00 02 00 01 04 b0 00 00 00 20 20: 00 f0 ff 21 00 00 00 22 00 f0 ff 23 00 10 00 00 30: fc 10 00 00 00 14 00 00 fc 14 00 00 0a 01 c0 05 40: 11 0e 0d 00 01 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:09.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M (rev 64) (prog-if 00 [VGA]) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (2000ns min), cache line size 04 Interrupt: pin A routed to IRQ 0 Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 3000 [size=256] Region 2: Memory at c1000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at 24000000 [disabled] [size=128K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 10 52 4c 87 00 90 02 64 00 00 03 04 00 00 00 10: 00 00 00 c0 01 30 00 00 00 00 00 c1 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 5c 00 00 00 00 00 00 00 ff 01 08 00
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 3e00 [size=256] Region 1: Memory at e9100000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: ec 10 39 81 07 00 90 02 10 00 00 02 00 80 00 00 10: 01 3e 00 00 00 00 10 e9 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
00:0b.0 FireWire (IEEE 1394): NEC Corporation IEEE 1394 [OrangeLink] Host Controller (rev 02) (prog-if 10 [OHCI]) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 04 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 24021000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 33 10 cd 00 56 01 90 02 02 10 00 0c 04 40 00 00 10: 00 10 02 24 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 00 00
# dmesg Linux version 2.6.17-g9fda2669 (root@thor) (gcc version 3.4.6 (Gentoo 3.4.6-r1, ssp-3.4.5-1.0, pie-8.7.9)) #9 PREEMPT Thu Jun 22 23:12:24 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000fff0000 (usable) BIOS-e820: 000000000fff0000 - 000000000fffffc0 (ACPI data) BIOS-e820: 000000000fffffc0 - 0000000010000000 (ACPI NVS) BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved) 255MB LOWMEM available. On node 0 totalpages: 65520 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 61424 pages, LIFO batch:15 DMI not present or invalid. Allocating PCI resources starting at 20000000 (gap: 10000000:effc0000) Built 1 zonelists Kernel command line: BOOT_IMAGE=git ro root=301 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 1024 (order: 10, 4096 bytes) Detected 500.182 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256432k/262080k available (1946k kernel code, 5152k reserved, 657k data, 120k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1001.09 BogoMIPS (lpj=500548) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel Pentium III (Coppermine) stepping 06 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xeb180, last bus=0 Setting up standard PCI resources SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Scanning bus 0000:00 PCI: Found 0000:00:00.0 [8086/7194] 000600 00 PCI: Calling quirk c01de102 for 0000:00:00.0 PCI: Calling quirk c02941c5 for 0000:00:00.0 PCI: Calling quirk c029432b for 0000:00:00.0 PCI: Calling quirk c029448a for 0000:00:00.0 PCI: Found 0000:00:00.1 [8086/7195] 000401 00 PCI: Calling quirk c01de102 for 0000:00:00.1 PCI: Calling quirk c02941c5 for 0000:00:00.1 PCI: Calling quirk c029432b for 0000:00:00.1 PCI: Calling quirk c029448a for 0000:00:00.1 PCI: Found 0000:00:00.2 [8086/7196] 000703 00 PCI: Calling quirk c01de102 for 0000:00:00.2 PCI: Calling quirk c02941c5 for 0000:00:00.2 PCI: Calling quirk c029432b for 0000:00:00.2 PCI: Calling quirk c029448a for 0000:00:00.2 PCI: Found 0000:00:07.0 [8086/7198] 000601 00 PCI: Calling quirk c01de102 for 0000:00:07.0 PCI: Calling quirk c02941c5 for 0000:00:07.0 PCI: Calling quirk c029432b for 0000:00:07.0 PCI: Calling quirk c029448a for 0000:00:07.0 PCI: Found 0000:00:07.1 [8086/7199] 000101 00 PCI: Calling quirk c01de102 for 0000:00:07.1 PCI: Calling quirk c02941c5 for 0000:00:07.1 PCI: Calling quirk c029432b for 0000:00:07.1 PCI: Calling quirk c029448a for 0000:00:07.1 PCI: Found 0000:00:07.2 [8086/719a] 000c03 00 PCI: Calling quirk c01de102 for 0000:00:07.2 PCI: Calling quirk c02941c5 for 0000:00:07.2 PCI: Calling quirk c029432b for 0000:00:07.2 PCI: Calling quirk c029448a for 0000:00:07.2 PCI: Found 0000:00:07.3 [8086/719b] 000680 00 PCI: Calling quirk c01de102 for 0000:00:07.3 PCI: Calling quirk c02941c5 for 0000:00:07.3 PCI: Calling quirk c029432b for 0000:00:07.3 PCI: Calling quirk c029448a for 0000:00:07.3 PCI: Found 0000:00:08.0 [104c/ac50] 000607 02 PCI: Calling quirk c01de102 for 0000:00:08.0 PCI: Calling quirk c02941c5 for 0000:00:08.0 PCI: Calling quirk c029448a for 0000:00:08.0 PCI: Found 0000:00:09.0 [1002/4c52] 000300 00 PCI: Calling quirk c01de102 for 0000:00:09.0 PCI: Calling quirk c02941c5 for 0000:00:09.0 PCI: Calling quirk c029448a for 0000:00:09.0 Boot video device is 0000:00:09.0 PCI: Found 0000:00:0a.0 [10ec/8139] 000200 00 PCI: Calling quirk c01de102 for 0000:00:0a.0 PCI: Calling quirk c02941c5 for 0000:00:0a.0 PCI: Calling quirk c029448a for 0000:00:0a.0 PCI: Found 0000:00:0b.0 [1033/00cd] 000c00 00 PCI: Calling quirk c01de102 for 0000:00:0b.0 PCI: Calling quirk c02941c5 for 0000:00:0b.0 PCI: Calling quirk c029448a for 0000:00:0b.0 PCI: Fixups for bus 0000:00 PCI: Scanning behind PCI bridge 0000:00:08.0, config 000040, pass 0 PCI: Scanning behind PCI bridge 0000:00:08.0, config 000040, pass 1 PCI: Bus scan for 0000:00 returning with max=04 PCI: Using IRQ router PIIX/ICH [8086/7198] at 0000:00:07.0 PCI: Cannot allocate resource region 0 of device 0000:00:0b.0 PCI: BIOS reporting unknown device 00:01 PCI: BIOS reporting unknown device 00:02 got res [24000000:2401ffff] bus [24000000:2401ffff] flags 7202 for BAR 6 of 0000:00:09.0 got res [24020000:24020fff] bus [24020000:24020fff] flags 200 for BAR 0 of 0000:00:08.0 PCI: moved device 0000:00:08.0 resource 0 (200) to 24020000 got res [24021000:24021fff] bus [24021000:24021fff] flags 200 for BAR 0 of 0000:00:0b.0 PCI: moved device 0000:00:0b.0 resource 0 (200) to 24021000 PCI: Bus 1, cardbus bridge: 0000:00:08.0 IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 20000000-21ffffff MEM window: 22000000-23ffffff PCI: Found IRQ 10 for device 0000:00:08.0 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered NTFS driver 2.1.27 [Flags: R/O]. Initializing Cryptographic API io scheduler noop registered io scheduler cfq registered (default) PCI: Calling quirk c01de03c for 0000:00:00.0 PCI: Calling quirk c0244ebc for 0000:00:00.0 PCI: Calling quirk c01de03c for 0000:00:00.1 PCI: Calling quirk c0244ebc for 0000:00:00.1 PCI: Calling quirk c01de03c for 0000:00:00.2 PCI: Calling quirk c0244ebc for 0000:00:00.2 PCI: Calling quirk c01de03c for 0000:00:07.0 PCI: Calling quirk c0244ebc for 0000:00:07.0 PCI: Calling quirk c01de03c for 0000:00:07.1 PCI: Calling quirk c0244ebc for 0000:00:07.1 PCI: Calling quirk c01de03c for 0000:00:07.2 PCI: Calling quirk c0244ebc for 0000:00:07.2 PCI: Calling quirk c01de03c for 0000:00:07.3 PCI: Calling quirk c0244ebc for 0000:00:07.3 PCI: Calling quirk c01de03c for 0000:00:08.0 PCI: Calling quirk c0244ebc for 0000:00:08.0 PCI: Calling quirk c01de03c for 0000:00:09.0 PCI: Calling quirk c0244ebc for 0000:00:09.0 PCI: Calling quirk c01de03c for 0000:00:0a.0 PCI: Calling quirk c0244ebc for 0000:00:0a.0 PCI: Calling quirk c01de03c for 0000:00:0b.0 PCI: Calling quirk c0244ebc for 0000:00:0b.0 vesafb: framebuffer at 0xc0000000, mapped to 0xd0800000, using 1536k, total 4096k vesafb: mode is 1024x768x8, linelength=1024, pages=4 vesafb: protected mode interface info at c000:4f84 vesafb: scrolling: redraw vesafb: Pseudocolor: size=6:6:6:6, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 PCI: Found IRQ 10 for device 0000:00:0a.0 IRQ routing conflict for 0000:00:0a.0, have irq 11, want irq 10 eth0: RealTek RTL8139 at 0x3e00, 00:40:d0:17:96:b1, IRQ 11 eth0: Identified 8139 chip type 'RTL-8139C' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 0 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... hda: IC25N020ATCS04-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 hda3 PCI: Found IRQ 10 for device 0000:00:08.0 Yenta: CardBus bridge found at 0000:00:08.0 [0e11:000d] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:08.0, mfunc 0x017c1602, devctl 0x64 Yenta: ISA IRQ mask 0x02d8, PCI irq 10 Socket status: 30000010 USB Universal Host Controller Interface driver v3.0
PCI: IRQ 11 for device 0000:00:07.2 doesn't match PIRQ mask - try pci=usepirqmask <6>PCI: Found IRQ 11 for device 0000:00:07.2 PCI: Sharing IRQ 11 with 0000:00:0b.0 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 11, io base 0x00001200 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new driver cdc_acm drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC). PCI: Setting latency timer of device 0000:00:00.1 to 64 input: AT Translated Set 2 keyboard as /class/input/input0 pccard: PCMCIA card inserted into slot 0 intel8x0_measure_ac97_clock: measured 50113 usecs intel8x0: clocking to 48000 ALSA device list: #0: Intel 440MX with CS4299 at 0x1600, irq 5 TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ReiserFS: hda1: found reiserfs format "3.6" with standard journal Synaptics Touchpad, model: 1, fw: 4.1, id: 0x8848a1, caps: 0x0/0x0 input: SynPS/2 Synaptics TouchPad as /class/input/input1 ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: replayed 12 transactions in 7 seconds ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 120k freed Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 across:265064k ReiserFS: hda1: Removing [15923 112983 0x0 SD]..done ReiserFS: hda1: There were 1 uncompleted unlinks/truncates. Completed NTFS volume version 3.1. pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xe0000-0xfffff cs: memory probe 0x60000000-0x60ffffff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
************************************************** I reverted commit 4196c3af25d98204216a5d6c37ad2cb303a1f2bf and compiled it *with* APM support: **************************************************
# /sbin/lspci -vvx 00:00.0 Host bridge: Intel Corp. 82440MX Host Bridge (rev 01) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64 00: 86 80 94 71 06 00 00 22 01 00 00 06 00 40 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:00.1 Multimedia audio controller: Intel Corp. 82440MX AC'97 Audio Controller Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at 1600 [size=256] Region 1: I/O ports at 1500 [size=64] 00: 86 80 95 71 05 00 00 00 00 00 01 04 00 00 00 00 10: 01 16 00 00 01 15 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
00:00.2 Modem: Intel Corp. 82440MX AC'97 Modem Controller (prog-if 00 [Generic]) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at 1800 [size=256] Region 1: I/O ports at 1700 [size=128] 00: 86 80 96 71 05 00 00 00 00 00 03 07 00 00 00 00 10: 01 18 00 00 01 17 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
00:07.0 ISA bridge: Intel Corp. 82440MX ISA Bridge (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00: 86 80 98 71 0f 00 80 02 01 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Intel Corp. 82440MX EIDE Controller (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 1100 [size=16] 00: 86 80 99 71 05 00 80 02 00 80 01 01 00 40 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.2 USB Controller: Intel Corp. 82440MX USB Universal Host Controller (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 240 Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at 1200 [size=32] 00: 86 80 9a 71 05 00 80 22 00 00 03 0c 00 f0 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
00:07.3 Bridge: Intel Corp. 82440MX Power Management Controller Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- 00: 86 80 9b 71 01 00 80 02 00 00 80 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, cache line size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 24020000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=01, subordinate=04, sec-latency=176 Memory window 0: 20000000-21fff000 (prefetchable) Memory window 1: 22000000-23fff000 I/O window 0: 00002000-00002fff I/O window 1: 00004000-00004fff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 00: 4c 10 50 ac 07 00 10 02 01 00 07 06 08 a8 02 00 10: 00 00 02 24 a0 00 00 02 00 01 04 b0 00 00 00 20 20: 00 f0 ff 21 00 00 00 22 00 f0 ff 23 00 20 00 00 30: fc 2f 00 00 00 40 00 00 fc 4f 00 00 0a 01 c0 05 40: 11 0e 0d 00 01 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:09.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M (rev 64) (prog-if 00 [VGA]) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (2000ns min), cache line size 04 Interrupt: pin A routed to IRQ 0 Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 3000 [size=256] Region 2: Memory at c1000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at 24000000 [disabled] [size=128K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 02 10 52 4c 87 00 90 02 64 00 00 03 04 00 00 00 10: 00 00 00 c0 01 30 00 00 00 00 00 c1 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 5c 00 00 00 00 00 00 00 ff 01 08 00
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 3e00 [size=256] Region 1: Memory at e9100000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: ec 10 39 81 07 00 90 02 10 00 00 02 00 80 00 00 10: 01 3e 00 00 00 00 10 e9 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
00:0b.0 FireWire (IEEE 1394): NEC Corporation IEEE 1394 [OrangeLink] Host Controller (rev 02) (prog-if 10 [OHCI]) Subsystem: Compaq Computer Corporation: Unknown device 000d Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 04 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 24021000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: 33 10 cd 00 56 01 90 02 02 10 00 0c 04 40 00 00 10: 00 10 02 24 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 11 0e 0d 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 00 00
# dmesg Linux version 2.6.17-g95e5c611 (root@thor) (gcc version 3.4.6 (Gentoo 3.4.6-r1, ssp-3.4.5-1.0, pie-8.7.9)) #5 PREEMPT Thu Jun 22 22:12:00 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000fff0000 (usable) BIOS-e820: 000000000fff0000 - 000000000fffffc0 (ACPI data) BIOS-e820: 000000000fffffc0 - 0000000010000000 (ACPI NVS) BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved) 255MB LOWMEM available. On node 0 totalpages: 65520 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 61424 pages, LIFO batch:15 DMI not present or invalid. Allocating PCI resources starting at 20000000 (gap: 10000000:effc0000) Built 1 zonelists Kernel command line: BOOT_IMAGE=git-b ro root=301 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 1024 (order: 10, 4096 bytes) Detected 500.038 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256420k/262080k available (1951k kernel code, 5164k reserved, 660k data, 124k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1001.07 BogoMIPS (lpj=500536) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel Pentium III (Coppermine) stepping 06 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xeb180, last bus=0 Setting up standard PCI resources SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Scanning bus 0000:00 PCI: Found 0000:00:00.0 [8086/7194] 000600 00 PCI: Calling quirk c01df586 for 0000:00:00.0 PCI: Calling quirk c0295649 for 0000:00:00.0 PCI: Calling quirk c02957af for 0000:00:00.0 PCI: Calling quirk c029590e for 0000:00:00.0 PCI: Found 0000:00:00.1 [8086/7195] 000401 00 PCI: Calling quirk c01df586 for 0000:00:00.1 PCI: Calling quirk c0295649 for 0000:00:00.1 PCI: Calling quirk c02957af for 0000:00:00.1 PCI: Calling quirk c029590e for 0000:00:00.1 PCI: Found 0000:00:00.2 [8086/7196] 000703 00 PCI: Calling quirk c01df586 for 0000:00:00.2 PCI: Calling quirk c0295649 for 0000:00:00.2 PCI: Calling quirk c02957af for 0000:00:00.2 PCI: Calling quirk c029590e for 0000:00:00.2 PCI: Found 0000:00:07.0 [8086/7198] 000601 00 PCI: Calling quirk c01df586 for 0000:00:07.0 PCI: Calling quirk c0295649 for 0000:00:07.0 PCI: Calling quirk c02957af for 0000:00:07.0 PCI: Calling quirk c029590e for 0000:00:07.0 PCI: Found 0000:00:07.1 [8086/7199] 000101 00 PCI: Calling quirk c01df586 for 0000:00:07.1 PCI: Calling quirk c0295649 for 0000:00:07.1 PCI: Calling quirk c02957af for 0000:00:07.1 PCI: Calling quirk c029590e for 0000:00:07.1 PCI: Found 0000:00:07.2 [8086/719a] 000c03 00 PCI: Calling quirk c01df586 for 0000:00:07.2 PCI: Calling quirk c0295649 for 0000:00:07.2 PCI: Calling quirk c02957af for 0000:00:07.2 PCI: Calling quirk c029590e for 0000:00:07.2 PCI: Found 0000:00:07.3 [8086/719b] 000680 00 PCI: Calling quirk c01df586 for 0000:00:07.3 PCI: Calling quirk c0295649 for 0000:00:07.3 PCI: Calling quirk c02957af for 0000:00:07.3 PCI: Calling quirk c029590e for 0000:00:07.3 PCI: Found 0000:00:08.0 [104c/ac50] 000607 02 PCI: Calling quirk c01df586 for 0000:00:08.0 PCI: Calling quirk c0295649 for 0000:00:08.0 PCI: Calling quirk c029590e for 0000:00:08.0 PCI: Found 0000:00:09.0 [1002/4c52] 000300 00 PCI: Calling quirk c01df586 for 0000:00:09.0 PCI: Calling quirk c0295649 for 0000:00:09.0 PCI: Calling quirk c029590e for 0000:00:09.0 Boot video device is 0000:00:09.0 PCI: Found 0000:00:0a.0 [10ec/8139] 000200 00 PCI: Calling quirk c01df586 for 0000:00:0a.0 PCI: Calling quirk c0295649 for 0000:00:0a.0 PCI: Calling quirk c029590e for 0000:00:0a.0 PCI: Found 0000:00:0b.0 [1033/00cd] 000c00 00 PCI: Calling quirk c01df586 for 0000:00:0b.0 PCI: Calling quirk c0295649 for 0000:00:0b.0 PCI: Calling quirk c029590e for 0000:00:0b.0 PCI: Fixups for bus 0000:00 PCI: Scanning behind PCI bridge 0000:00:08.0, config 000040, pass 0 PCI: Scanning behind PCI bridge 0000:00:08.0, config 000040, pass 1 PCI: Bus scan for 0000:00 returning with max=04 PCI: Using IRQ router PIIX/ICH [8086/7198] at 0000:00:07.0 PCI: Cannot allocate resource region 0 of device 0000:00:0b.0 PCI: BIOS reporting unknown device 00:01 PCI: BIOS reporting unknown device 00:02 got res [24000000:2401ffff] bus [24000000:2401ffff] flags 7202 for BAR 6 of 0000:00:09.0 got res [24020000:24020fff] bus [24020000:24020fff] flags 200 for BAR 0 of 0000:00:08.0 PCI: moved device 0000:00:08.0 resource 0 (200) to 24020000 got res [24021000:24021fff] bus [24021000:24021fff] flags 200 for BAR 0 of 0000:00:0b.0 PCI: moved device 0000:00:0b.0 resource 0 (200) to 24021000 PCI: Bus 1, cardbus bridge: 0000:00:08.0 IO window: 00002000-00002fff IO window: 00004000-00004fff PREFETCH window: 20000000-21ffffff MEM window: 22000000-23ffffff PCI: Found IRQ 10 for device 0000:00:08.0 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) NTFS driver 2.1.27 [Flags: R/O]. Initializing Cryptographic API io scheduler noop registered io scheduler cfq registered (default) PCI: Calling quirk c01df4c0 for 0000:00:00.0 PCI: Calling quirk c0246340 for 0000:00:00.0 PCI: Calling quirk c01df4c0 for 0000:00:00.1 PCI: Calling quirk c0246340 for 0000:00:00.1 PCI: Calling quirk c01df4c0 for 0000:00:00.2 PCI: Calling quirk c0246340 for 0000:00:00.2 PCI: Calling quirk c01df4c0 for 0000:00:07.0 PCI: Calling quirk c0246340 for 0000:00:07.0 PCI: Calling quirk c01df4c0 for 0000:00:07.1 PCI: Calling quirk c0246340 for 0000:00:07.1 PCI: Calling quirk c01df4c0 for 0000:00:07.2 PCI: Calling quirk c0246340 for 0000:00:07.2 PCI: Calling quirk c01df4c0 for 0000:00:07.3 PCI: Calling quirk c0246340 for 0000:00:07.3 PCI: Calling quirk c01df4c0 for 0000:00:08.0 PCI: Calling quirk c0246340 for 0000:00:08.0 PCI: Calling quirk c01df4c0 for 0000:00:09.0 PCI: Calling quirk c0246340 for 0000:00:09.0 PCI: Calling quirk c01df4c0 for 0000:00:0a.0 PCI: Calling quirk c0246340 for 0000:00:0a.0 PCI: Calling quirk c01df4c0 for 0000:00:0b.0 PCI: Calling quirk c0246340 for 0000:00:0b.0 vesafb: framebuffer at 0xc0000000, mapped to 0xd0800000, using 1536k, total 4096k vesafb: mode is 1024x768x8, linelength=1024, pages=4 vesafb: protected mode interface info at c000:4f84 vesafb: scrolling: redraw vesafb: Pseudocolor: size=6:6:6:6, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac loop: loaded (max 8 devices) 8139too Fast Ethernet driver 0.9.27 PCI: Found IRQ 10 for device 0000:00:0a.0 IRQ routing conflict for 0000:00:0a.0, have irq 11, want irq 10 eth0: RealTek RTL8139 at 0x3e00, 00:40:d0:17:96:b1, IRQ 11 eth0: Identified 8139 chip type 'RTL-8139C' Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 0 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... hda: IC25N020ATCS04-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 hda3 PCI: Found IRQ 10 for device 0000:00:08.0 Yenta: CardBus bridge found at 0000:00:08.0 [0e11:000d] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:08.0, mfunc 0x017c1602, devctl 0x64 Yenta: ISA IRQ mask 0x02d8, PCI irq 10 Socket status: 30000010 USB Universal Host Controller Interface driver v3.0
PCI: IRQ 11 for device 0000:00:07.2 doesn't match PIRQ mask - try pci=usepirqmask <6>PCI: Found IRQ 11 for device 0000:00:07.2 PCI: Sharing IRQ 11 with 0000:00:0b.0 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 11, io base 0x00001200 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new driver cdc_acm drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC). PCI: Setting latency timer of device 0000:00:00.1 to 64 input: AT Translated Set 2 keyboard as /class/input/input0 pccard: PCMCIA card inserted into slot 0 intel8x0_measure_ac97_clock: measured 50190 usecs intel8x0: clocking to 48000 ALSA device list: #0: Intel 440MX with CS4299 at 0x1600, irq 5 TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ReiserFS: hda1: found reiserfs format "3.6" with standard journal Synaptics Touchpad, model: 1, fw: 4.1, id: 0x8848a1, caps: 0x0/0x0 input: SynPS/2 Synaptics TouchPad as /class/input/input1 ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 124k freed Adding 265064k swap on /dev/hda2. Priority:-1 extents:1 across:265064k NTFS volume version 3.1. pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xe0000-0xfffff cs: memory probe 0x60000000-0x60ffffff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Like before, I'm available for any other test.
bye, thank you very much Alessio Sangalli
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |