lkml.org 
[lkml]   [2006]   [Jun]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject[2.6.17-rc5-mm2] crash when doing second suspend: BUG in arch/i386/kernel/nmi.c:174
I'm trying to get suspend/resume working properly on my Thinkpad X60.
This is a dual-core machine, so its running in SMP mode.

Now that I have a set of patches to make AHCI resume properly, I'm
getting a crash on the second suspend. I can't get an actual listing of
the oops, but I have a set of screenshots if anyone needs more details.

The gist is that there's a BUG_ON failing at arch/i386/kernel/nmi.c:174
(BUG_ON(counter > NMI_MAX_COUNTER_BITS)), in release_evntsel_nmi. The
backtrace is:

release_evntsel_nmi
stop_apci_nmi_watchdog
on_each_cpu
disable_lapic_nmi_watchdog
lapic_nmi_suspend
sysdev_suspend
device_power_down
suspend_enter
enter_state
state_store
subsys_attr_store
sysfs_write_file
vfs_write
sys_write
sysenter_past_esp

This happens after all the devices have suspended themselves; then
there's a longish pause (several seconds), and the oops appears. The
first suspend is very quick.

Everything works as expected when I disable nmi watchdog with
nmi_watchdog=0 on the kernel command line.

dmesg after a single successful suspend/resume cycle attached.
(resent without .config to get under linux-kernel's size limit; mail if
you want a copy)

J


Linux version 2.6.17-rc5-mm2 (jeremy@ezr) (gcc version 4.1.1 20060525 (Red Hat 4.1.1-1)) #10 SMP Fri Jun 2 01:23:24 PDT 2006
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1
copy_e820_map() type is E820_RAM
add_memory_region(0000000000000000, 000000000009f000, 1)
copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2
add_memory_region(000000000009f000, 0000000000001000, 2)
copy_e820_map() start: 00000000000d2000 size: 0000000000002000 end: 00000000000d4000 type: 2
add_memory_region(00000000000d2000, 0000000000002000, 2)
copy_e820_map() start: 00000000000dc000 size: 0000000000024000 end: 0000000000100000 type: 2
add_memory_region(00000000000dc000, 0000000000024000, 2)
copy_e820_map() start: 0000000000100000 size: 000000007f5d0000 end: 000000007f6d0000 type: 1
copy_e820_map() type is E820_RAM
add_memory_region(0000000000100000, 000000007f5d0000, 1)
copy_e820_map() start: 000000007f6d0000 size: 0000000000013000 end: 000000007f6e3000 type: 3
add_memory_region(000000007f6d0000, 0000000000013000, 3)
copy_e820_map() start: 000000007f6e3000 size: 000000000001d000 end: 000000007f700000 type: 4
add_memory_region(000000007f6e3000, 000000000001d000, 4)
copy_e820_map() start: 000000007f700000 size: 0000000000900000 end: 0000000080000000 type: 2
add_memory_region(000000007f700000, 0000000000900000, 2)
copy_e820_map() start: 00000000f0000000 size: 0000000004000000 end: 00000000f4000000 type: 2
add_memory_region(00000000f0000000, 0000000004000000, 2)
copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2
add_memory_region(00000000fec00000, 0000000000010000, 2)
copy_e820_map() start: 00000000fed00000 size: 0000000000000400 end: 00000000fed00400 type: 2
add_memory_region(00000000fed00000, 0000000000000400, 2)
copy_e820_map() start: 00000000fed14000 size: 0000000000006000 end: 00000000fed1a000 type: 2
add_memory_region(00000000fed14000, 0000000000006000, 2)
copy_e820_map() start: 00000000fed1c000 size: 0000000000074000 end: 00000000fed90000 type: 2
add_memory_region(00000000fed1c000, 0000000000074000, 2)
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
add_memory_region(00000000fee00000, 0000000000001000, 2)
copy_e820_map() start: 00000000ff800000 size: 0000000000800000 end: 0000000100000000 type: 2
add_memory_region(00000000ff800000, 0000000000800000, 2)
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007f6d0000 (usable)
BIOS-e820: 000000007f6d0000 - 000000007f6e3000 (ACPI data)
BIOS-e820: 000000007f6e3000 - 000000007f700000 (ACPI NVS)
BIOS-e820: 000000007f700000 - 0000000080000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
1142MB HIGHMEM available.
895MB LOWMEM available.
found SMP MP-table at 000f68c0
NX (Execute Disable) protection: active
On node 0 totalpages: 521936
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225279 pages, LIFO batch:31
node 0 zone HighMem misaligned start pfn, enable UNALIGNED_ZONE_BOUNDARIES
HighMem zone: 292561 pages, LIFO batch:31
DMI present.
Using APIC driver default
ACPI: RSDP (v002 LENOVO ) @ 0x000f6880
ACPI: XSDT (v001 LENOVO TP-7B 0x00001060 LTP 0x00000000) @ 0x7f6d6621
ACPI: FADT (v003 LENOVO TP-7B 0x00001060 LNVO 0x00000001) @ 0x7f6d6700
ACPI: SSDT (v001 LENOVO TP-7B 0x00001060 MSFT 0x0100000e) @ 0x7f6d68b4
ACPI: ECDT (v001 LENOVO TP-7B 0x00001060 LNVO 0x00000001) @ 0x7f6e2d4a
ACPI: TCPA (v002 LENOVO TP-7B 0x00001060 LNVO 0x00000001) @ 0x7f6e2d9c
ACPI: MADT (v001 LENOVO TP-7B 0x00001060 LNVO 0x00000001) @ 0x7f6e2dce
ACPI: MCFG (v001 LENOVO TP-7B 0x00001060 LNVO 0x00000001) @ 0x7f6e2e36
ACPI: HPET (v001 LENOVO TP-7B 0x00001060 LNVO 0x00000001) @ 0x7f6e2e74
ACPI: BOOT (v001 LENOVO TP-7B 0x00001060 LTP 0x00000001) @ 0x7f6e2fd8
ACPI: SSDT (v001 LENOVO TP-7B 0x00001060 INTL 0x20050513) @ 0x7f6d5bdc
ACPI: SSDT (v001 LENOVO TP-7B 0x00001060 INTL 0x20050513) @ 0x7f6d5a04
ACPI: DSDT (v001 LENOVO TP-7B 0x00001060 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:70000000)
Detected 1828.944 MHz processor.
Built 1 zonelists
Kernel command line: ro root=LABEL=/
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c04ae000 soft=c048e000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
------------------------
| Locking API testsuite:
----------------------------------------------------------------------------
| spin |wlock |rlock |mutex | wsem | rsem |
--------------------------------------------------------------------------
A-A deadlock:failed|failed|failed|failed|failed|failed|
A-B-B-A deadlock:failed|failed| ok |failed|failed|failed|
A-B-B-C-C-A deadlock:failed|failed| ok |failed|failed|failed|
A-B-C-A-B-C deadlock:failed|failed| ok |failed|failed|failed|
A-B-B-C-C-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
A-B-C-D-B-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
A-B-C-D-B-C-D-A deadlock:failed|failed| ok |failed|failed|failed|
double unlock: ok | ok |failed|failed|failed|failed|
bad unlock order:failed|failed|failed|failed|failed|failed|
--------------------------------------------------------------------------
recursive read-lock: | ok | |failed|
--------------------------------------------------------------------------
hard-irqs-on + irq-safe-A/12:failed|failed| ok |
soft-irqs-on + irq-safe-A/12:failed|failed| ok |
hard-irqs-on + irq-safe-A/21:failed|failed| ok |
soft-irqs-on + irq-safe-A/21:failed|failed| ok |
sirq-safe-A => hirqs-on/12:failed|failed| ok |
sirq-safe-A => hirqs-on/21:failed|failed| ok |
hard-safe-A + irqs-on/12:failed|failed| ok |
soft-safe-A + irqs-on/12:failed|failed| ok |
hard-safe-A + irqs-on/21:failed|failed| ok |
soft-safe-A + irqs-on/21:failed|failed| ok |
hard-safe-A + unsafe-B #1/123:failed|failed| ok |
soft-safe-A + unsafe-B #1/123:failed|failed| ok |
hard-safe-A + unsafe-B #1/132:failed|failed| ok |
soft-safe-A + unsafe-B #1/132:failed|failed| ok |
hard-safe-A + unsafe-B #1/213:failed|failed| ok |
soft-safe-A + unsafe-B #1/213:failed|failed| ok |
hard-safe-A + unsafe-B #1/231:failed|failed| ok |
soft-safe-A + unsafe-B #1/231:failed|failed| ok |
hard-safe-A + unsafe-B #1/312:failed|failed| ok |
soft-safe-A + unsafe-B #1/312:failed|failed| ok |
hard-safe-A + unsafe-B #1/321:failed|failed| ok |
soft-safe-A + unsafe-B #1/321:failed|failed| ok |
hard-safe-A + unsafe-B #2/123:failed|failed| ok |
soft-safe-A + unsafe-B #2/123:failed|failed| ok |
hard-safe-A + unsafe-B #2/132:failed|failed| ok |
soft-safe-A + unsafe-B #2/132:failed|failed| ok |
hard-safe-A + unsafe-B #2/213:failed|failed| ok |
soft-safe-A + unsafe-B #2/213:failed|failed| ok |
hard-safe-A + unsafe-B #2/231:failed|failed| ok |
soft-safe-A + unsafe-B #2/231:failed|failed| ok |
hard-safe-A + unsafe-B #2/312:failed|failed| ok |
soft-safe-A + unsafe-B #2/312:failed|failed| ok |
hard-safe-A + unsafe-B #2/321:failed|failed| ok |
soft-safe-A + unsafe-B #2/321:failed|failed| ok |
hard-irq lock-inversion/123:failed|failed| ok |
soft-irq lock-inversion/123:failed|failed| ok |
hard-irq lock-inversion/132:failed|failed| ok |
soft-irq lock-inversion/132:failed|failed| ok |
hard-irq lock-inversion/213:failed|failed| ok |
soft-irq lock-inversion/213:failed|failed| ok |
hard-irq lock-inversion/231:failed|failed| ok |
soft-irq lock-inversion/231:failed|failed| ok |
hard-irq lock-inversion/312:failed|failed| ok |
soft-irq lock-inversion/312:failed|failed| ok |
hard-irq lock-inversion/321:failed|failed| ok |
soft-irq lock-inversion/321:failed|failed| ok |
hard-irq read-recursion/123: ok |
soft-irq read-recursion/123: ok |
hard-irq read-recursion/132: ok |
soft-irq read-recursion/132: ok |
hard-irq read-recursion/213: ok |
soft-irq read-recursion/213: ok |
hard-irq read-recursion/231: ok |
soft-irq read-recursion/231: ok |
hard-irq read-recursion/312: ok |
soft-irq read-recursion/312: ok |
hard-irq read-recursion/321: ok |
soft-irq read-recursion/321: ok |
--------------------------------------------------------
139 out of 206 testcases failed, as expected. |
----------------------------------------------------
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2059716k/2087744k available (2151k kernel code, 26752k reserved, 865k data, 232k init, 1170244k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Calibrating delay using timer specific routine.. 3662.28 BogoMIPS (lpj=7324578)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
CPU0: Intel Genuine Intel(R) CPU T2400 @ 1.83GHz stepping 08
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c04af000 soft=c048f000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3657.66 BogoMIPS (lpj=7315332)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2400 @ 1.83GHz stepping 08
Total of 2 processors activated (7319.95 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs:
Brought up 2 CPUs
migration_cost=73
checking if image is initramfs... it is
Freeing initrd memory: 1036k freed
PM: Adding info for No Bus:platform
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 2.10 entry at 0xfd82b, last bus=24
Setting up standard PCI resources
ACPI: Subsystem revision 20060310
ACPI: Found ECDT
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:acpi
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PM: Adding info for No Bus:pci0000:00
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:02.1
PM: Adding info for pci:0000:00:1b.0
PM: Adding info for pci:0000:00:1c.0
PM: Adding info for pci:0000:00:1c.1
PM: Adding info for pci:0000:00:1c.2
PM: Adding info for pci:0000:00:1c.3
PM: Adding info for pci:0000:00:1d.0
PM: Adding info for pci:0000:00:1d.1
PM: Adding info for pci:0000:00:1d.2
PM: Adding info for pci:0000:00:1d.3
PM: Adding info for pci:0000:00:1d.7
PM: Adding info for pci:0000:00:1e.0
PM: Adding info for pci:0000:00:1f.0
PM: Adding info for pci:0000:00:1f.1
PM: Adding info for pci:0000:00:1f.2
PM: Adding info for pci:0000:00:1f.3
PM: Adding info for pci:0000:02:00.0
PM: Adding info for pci:0000:03:00.0
PM: Adding info for pci:0000:15:00.0
PM: Adding info for pci:0000:15:00.1
PM: Adding info for pci:0000:15:00.2
ACPI: Embedded Controller [EC] (gpe 28) interrupt mode.
ACPI: Power Resource [PUBS] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
PM: Adding info for pnp:00:0a
PM: Adding info for pnp:00:0b
pnp: PnP ACPI: found 12 devices
Intel 82802 RNG detected
intel_rng: cannot enable RNG, aborting
intel_rng: RNG registering failed (-5)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
IO window: 2000-2fff
MEM window: ee000000-ee0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: 3000-4fff
MEM window: ec000000-edffffff
PREFETCH window: e4000000-e40fffff
PCI: Bridge: 0000:00:1c.2
IO window: 5000-6fff
MEM window: e8000000-e9ffffff
PREFETCH window: e4100000-e41fffff
PCI: Bridge: 0000:00:1c.3
IO window: 7000-8fff
MEM window: ea000000-ebffffff
PREFETCH window: e4200000-e42fffff
PCI: Bus 22, cardbus bridge: 0000:15:00.0
IO window: 00009000-000090ff
IO window: 00009400-000094ff
PREFETCH window: e0000000-e1ffffff
MEM window: e6000000-e7ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 9000-cfff
MEM window: e4300000-e7ffffff
PREFETCH window: e0000000-e3ffffff
ACPI (acpi_bus-0192): Device `EXP0]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI (acpi_bus-0192): Device `EXP1]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI (acpi_bus-0192): Device `EXP2]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI (acpi_bus-0192): Device `EXP3]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Enabling device 0000:00:1e.0 (0005 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI (acpi_bus-0192): Device `CDBS]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:15:00.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
PM: Adding info for platform:pcspkr
Simple Boot Flag at 0x35 set to 0x1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1149246804.984:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
PM: Adding info for pci_express:0000:00:1c.0:pcie00
Allocate Port Service[0000:00:1c.0:pcie02]
PM: Adding info for pci_express:0000:00:1c.0:pcie02
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
PM: Adding info for pci_express:0000:00:1c.1:pcie00
Allocate Port Service[0000:00:1c.1:pcie02]
PM: Adding info for pci_express:0000:00:1c.1:pcie02
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
PM: Adding info for pci_express:0000:00:1c.2:pcie00
Allocate Port Service[0000:00:1c.2:pcie02]
PM: Adding info for pci_express:0000:00:1c.2:pcie02
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
PM: Adding info for pci_express:0000:00:1c.3:pcie00
Allocate Port Service[0000:00:1c.3:pcie02]
PM: Adding info for pci_express:0000:00:1c.3:pcie02
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
PM: Adding info for platform:vesafb.0
ACPI: ACPI Dock Station Driver
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [THM0] (49 C)
ACPI: Thermal Zone [THM1] (46 C)
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
PM: Adding info for platform:serial8250
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) -> IRQ 20
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 20
Yenta: CardBus bridge found at 0000:15:00.0 [17aa:201c]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 20
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x9000 - 0xcfff
cs: IO port probe 0x9000-0xcfff: clean.
pcmcia: parent PCI bridge Memory window: 0xe4300000 - 0xe7ffffff
pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe3ffffff
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
PM: Adding info for platform:i8042
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
PM: Adding info for serio:serio1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 232k freed
Write protecting the kernel read-only data: 387k
Time: hpet clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
SCSI subsystem initialized
libata version 1.30 loaded.
ahci 0000:00:1f.2: version 1.3
ACPI (acpi_bus-0192): Device `SATA]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 20
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input1
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xF883E500 ctl 0x0 bmdma 0x0 irq 20
ata2: Could not start DMA engineof port (-1)
ata2: SATA max UDMA/133 cmd 0xF883E580 ctl 0x0 bmdma 0x0 irq 20
ata3: Could not start DMA engineof port (-1)
ata3: SATA max UDMA/133 cmd 0xF883E600 ctl 0x0 bmdma 0x0 irq 20
ata4: Could not start DMA engineof port (-1)
ata4: SATA max UDMA/133 cmd 0xF883E680 ctl 0x0 bmdma 0x0 irq 20
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: cfg 49:0f00 82:746b 83:7f69 84:6063 85:f469 86:3c49 87:6063 88:043f
ata1.00: ATA-7, max UDMA/100, 195371568 sectors: LBA48
ata1.00: configured for UDMA/100
scsi0 : ahci
PM: Adding info for No Bus:host0
ata2: SATA link down (SStatus 0 SControl 0)
scsi1 : ahci
PM: Adding info for No Bus:host1
ata3: SATA link down (SStatus 0 SControl 0)
scsi2 : ahci
PM: Adding info for No Bus:host2
ata4: SATA link down (SStatus 0 SControl 0)
scsi3 : ahci
PM: Adding info for No Bus:host3
PM: Adding info for No Bus:target0:0:0
Vendor: ATA Model: HTS541010G9SA00 Rev: MBZI
Type: Direct-Access ANSI SCSI revision: 05
PM: Adding info for scsi:0:0:0:0
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: sda7: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 13258130
ext3_orphan_cleanup: deleting unreferenced inode 13258129
ext3_orphan_cleanup: deleting unreferenced inode 13258128
ext3_orphan_cleanup: deleting unreferenced inode 13258108
ext3_orphan_cleanup: deleting unreferenced inode 13258107
EXT3-fs: sda7: 5 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1149246816.604:2): selinux=0 auid=4294967295
input: PC Speaker as /class/input/input2
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
PM: Adding info for usb:usb1
usb usb1: configuration #1 chosen from 1 choice
PM: Adding info for usb:1-0:1.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001840
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
PM: Adding info for usb:usb2
usb usb2: configuration #1 chosen from 1 choice
PM: Adding info for usb:2-0:1.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 22, io base 0x00001860
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
PM: Adding info for usb:usb3
usb usb3: configuration #1 chosen from 1 choice
PM: Adding info for usb:3-0:1.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001880
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
PM: Adding info for usb:usb4
usb usb4: configuration #1 chosen from 1 choice
PM: Adding info for usb:4-0:1.0
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PM: Adding info for No Bus:i2c-0
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xee444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.17-rc5-mm2 ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
PM: Adding info for usb:usb5
usb usb5: configuration #1 chosen from 1 choice
PM: Adding info for usb:5-0:1.0
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ieee1394: Initialized config rom entry `ip1394'
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.17.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
sd 0:0:0:0: Attached scsi generic sg0 type 0
wlan: 0.8.4.2 (svn r1615)
sdhci: Secure Digital Host Controller Interface driver, 0.11
sdhci: Copyright(c) Pierre Ossman
ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) -> IRQ 22
mmc0: SDHCI at 0xe4301800 irq 22 PIO
ath_rate_sample: 1.2 (svn r1615)
Intel(R) PRO/1000 Network Driver - version 7.0.38-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:02:00.0 to 64
cs: IO port probe 0x100-0x3af: excluding 0x1f0-0x1f7
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
e1000: 0000:02:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:16:d3:20:d2:0b
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:15:00.1[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:15:00.1 to 64
PM: Adding info for ieee1394:fw-host0
usb 4-2: new full speed USB device using uhci_hcd and address 2
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[e4301000-e43017ff] Max Packet=[2048] IR/IT contexts=[4/4]
ath_pci: 0.9.4.5 (svn r1615)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:03:00.0 to 64
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 10.3 phy 6.1 radio 10.2
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
usb 4-2: new device found, idVendor=0483, idProduct=2016
usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: Biometric Coprocessor
usb 4-2: Manufacturer: STMicroelectronics
PM: Adding info for usb:4-2
usb 4-2: configuration #1 chosen from 1 choice
PM: Adding info for usb:4-2:1.0
wifi0: Atheros 5212: mem=0xedf00000, irq=21
PM: Adding info for ieee1394:000ae40600142001
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000ae40600142001]
PM: Adding info for ieee1394:000ae40600142001-0
ACPI (acpi_bus-0192): Device `HDEF]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
Non-volatile memory driver v1.2
floppy0: no floppy controllers found
lp: driver loaded but no devices found
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: IBM ThinkPad ACPI Extras v0.12a
ibm_acpi: http://ibm-acpi.sf.net/
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
EXT3 FS on sda7, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 4192924k swap on /dev/sda6. Priority:-1 extents:1 across:4192924k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 224 bytes per conntrack
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ADDRCONF(NETDEV_UP): eth0: link is not ready
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 20
[drm] Initialized i915 1.4.0 20060119 on minor 0
sdhci: Secure Digital Host Controller Interface driver, 0.11
sdhci: Copyright(c) Pierre Ossman
ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) -> IRQ 22
mmc0: SDHCI at 0xe4301800 irq 22 PIO
PM: Adding info for mmc:mmc0:a95c
mmcblk0: mmc0:a95c SD512 495488KiB
mmcblk0: p1
uhci_hcd 0000:00:1d.3: remove, state 1
usb usb4: USB disconnect, address 1
usb 4-2: USB disconnect, address 2
PM: Removing info for usb:4-2:1.0
PM: Removing info for usb:4-2
PM: Removing info for usb:4-0:1.0
PM: Removing info for usb:usb4
uhci_hcd 0000:00:1d.3: USB bus 4 deregistered
uhci_hcd 0000:00:1d.2: remove, state 1
usb usb3: USB disconnect, address 1
PM: Removing info for usb:3-0:1.0
PM: Removing info for usb:usb3
uhci_hcd 0000:00:1d.2: USB bus 3 deregistered
uhci_hcd 0000:00:1d.1: remove, state 1
usb usb2: USB disconnect, address 1
PM: Removing info for usb:2-0:1.0
PM: Removing info for usb:usb2
uhci_hcd 0000:00:1d.1: USB bus 2 deregistered
uhci_hcd 0000:00:1d.0: remove, state 1
usb usb1: USB disconnect, address 1
PM: Removing info for usb:1-0:1.0
PM: Removing info for usb:usb1
uhci_hcd 0000:00:1d.0: USB bus 1 deregistered
PM: Preparing system for mem sleep
Freezing cpus ...
Breaking affinity for irq 0
Breaking affinity for irq 12
Breaking affinity for irq 20
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
Stopping tasks: ==========================================================================================================================================================|
Suspending device mmc0:a95c
mmcblk mmc0:a95c: suspend
Suspending device 000ae40600142001-0
Suspending device 000ae40600142001
Suspending device fw-host0
Suspending device 5-0:1.0
hub 5-0:1.0: suspend
Suspending device usb5
usb usb5: suspend, may wakeup
Suspending device i2c-0
Suspending device 0:0:0:0
sd 0:0:0:0: suspend
Suspending device target0:0:0
Suspending device host3
Suspending device host2
Suspending device host1
Suspending device host0
Suspending device serio1
Suspending device serio0
Suspending device i8042
i8042 i8042: suspend
Suspending device serial8250
serial8250 serial8250: suspend
Suspending device pnp1
Suspending device vesafb.0
vesafb.0: suspend
Suspending device 0000:00:1c.3:pcie02
0000:00:1c.3:pcie02: suspend
Suspending device 0000:00:1c.3:pcie00
0000:00:1c.3:pcie00: suspend
Suspending device 0000:00:1c.2:pcie02
0000:00:1c.2:pcie02: suspend
Suspending device 0000:00:1c.2:pcie00
0000:00:1c.2:pcie00: suspend
Suspending device 0000:00:1c.1:pcie02
0000:00:1c.1:pcie02: suspend
Suspending device 0000:00:1c.1:pcie00
0000:00:1c.1:pcie00: suspend
Suspending device 0000:00:1c.0:pcie02
0000:00:1c.0:pcie02: suspend
Suspending device 0000:00:1c.0:pcie00
0000:00:1c.0:pcie00: suspend
Suspending device pcspkr
pcspkr pcspkr: suspend
Suspending device 00:0b
00:0b: suspend
Suspending device 00:0a
00:0a: suspend
Suspending device 00:09
i8042 aux 00:09: suspend
Suspending device 00:08
i8042 kbd 00:08: suspend
Suspending device 00:07
00:07: suspend
Suspending device 00:06
00:06: suspend
Suspending device 00:05
00:05: suspend
Suspending device 00:04
00:04: suspend
Suspending device 00:03
00:03: suspend
Suspending device 00:02
system 00:02: suspend
Suspending device 00:01
00:01: suspend
Suspending device 00:00
system 00:00: suspend
Suspending device pnp0
Suspending device 0000:15:00.2
sdhci 0000:15:00.2: suspend
Suspending device 0000:15:00.1
ohci1394 0000:15:00.1: suspend
Suspending device 0000:15:00.0
yenta_cardbus 0000:15:00.0: suspend
Suspending device 0000:03:00.0
ath_pci 0000:03:00.0: suspend
Suspending device 0000:02:00.0
e1000 0000:02:00.0: suspend
Suspending device 0000:00:1f.3
i801_smbus 0000:00:1f.3: suspend
Suspending device 0000:00:1f.2
ahci 0000:00:1f.2: suspend
ACPI (acpi_bus-0192): Device `SATA]is not power manageable [20060310]
Suspending device 0000:00:1f.1
PIIX_IDE 0000:00:1f.1: suspend
Suspending device 0000:00:1f.0
0000:00:1f.0: suspend
Suspending device 0000:00:1e.0
0000:00:1e.0: suspend
Suspending device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: suspend, may wakeup
Suspending device 0000:00:1d.3
0000:00:1d.3: suspend
Suspending device 0000:00:1d.2
0000:00:1d.2: suspend
Suspending device 0000:00:1d.1
0000:00:1d.1: suspend
Suspending device 0000:00:1d.0
0000:00:1d.0: suspend
Suspending device 0000:00:1c.3
pcieport-driver 0000:00:1c.3: suspend
Suspending device 0000:00:1c.2
pcieport-driver 0000:00:1c.2: suspend
Suspending device 0000:00:1c.1
pcieport-driver 0000:00:1c.1: suspend
Suspending device 0000:00:1c.0
pcieport-driver 0000:00:1c.0: suspend
Suspending device 0000:00:1b.0
HDA Intel 0000:00:1b.0: suspend
Suspending device 0000:00:02.1
0000:00:02.1: suspend
Suspending device 0000:00:02.0
0000:00:02.0: suspend
Suspending device 0000:00:00.0
agpgart-intel 0000:00:00.0: suspend
Suspending device pci0000:00
Suspending device acpi
acpi: suspend
Suspending device platform
PM: Entering mem sleep
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
BUG: sleeping function called from invalid context at include/asm/semaphore.h:99
in_atomic():0, irqs_disabled():1
<c010493a> show_trace_log_lvl+0x58/0x163 <c0104fd8> show_trace+0xf/0x11
<c01050d1> dump_stack+0x15/0x17 <c02088a4> acpi_os_wait_semaphore+0x62/0xbd
<c021f044> acpi_ut_acquire_mutex+0x2a/0x7a <c021534a> acpi_set_register+0x5f/0x17d
<c021f678> acpi_pm_enter+0x8f/0xb3 <c0140526> suspend_enter+0x34/0x44
<c014069e> enter_state+0x168/0x1c6 <c0140781> state_store+0x85/0x99
<c01a4f7e> subsys_attr_store+0x1e/0x22 <c01a5071> sysfs_write_file+0xa7/0xce
<c016cf8b> vfs_write+0xa8/0x159 <c016d5bf> sys_write+0x41/0x67
<c03172ad> sysenter_past_esp+0x56/0x79
Back to C!
PM: Finishing wakeup.
acpi: resuming
agpgart-intel 0000:00:00.0: resuming
0000:00:02.0: resuming
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 20
0000:00:02.1: resuming
PM: Writing back config space on device 0000:00:02.1 at offset 1 (was 900000, writing 900003)
HDA Intel 0000:00:1b.0: resuming
PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100106, writing 100102)
ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1b.0 to 64
pcieport-driver 0000:00:1c.0: resuming
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
pcieport-driver 0000:00:1c.1: resuming
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
pcieport-driver 0000:00:1c.2: resuming
PM: Writing back config space on device 0000:00:1c.2 at offset 7 (was 20006050, writing 6050)
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
pcieport-driver 0000:00:1c.3: resuming
PM: Writing back config space on device 0000:00:1c.3 at offset 1 (was 100000, writing 100107)
PM: Writing back config space on device 0000:00:1c.3 at offset 3 (was 810000, writing 810010)
PM: Writing back config space on device 0000:00:1c.3 at offset 7 (was 20000000, writing 8070)
PM: Writing back config space on device 0000:00:1c.3 at offset 8 (was 0, writing ebf0ea00)
PM: Writing back config space on device 0000:00:1c.3 at offset 9 (was 10001, writing e421e421)
PM: Writing back config space on device 0000:00:1c.3 at offset f (was 40400, writing 4040b)
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
0000:00:1d.0: resuming
PM: Writing back config space on device 0000:00:1d.0 at offset 1 (was 2800005, writing 2800001)
0000:00:1d.1: resuming
PM: Writing back config space on device 0000:00:1d.1 at offset 1 (was 2800005, writing 2800001)
0000:00:1d.2: resuming
PM: Writing back config space on device 0000:00:1d.2 at offset 1 (was 2800005, writing 2800001)
0000:00:1d.3: resuming
PM: Writing back config space on device 0000:00:1d.3 at offset 1 (was 2800005, writing 2800001)
ehci_hcd 0000:00:1d.7: resuming
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
0000:00:1e.0: resuming
PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100005, writing 100007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
0000:00:1f.0: resuming
PIIX_IDE 0000:00:1f.1: resuming
ACPI: PCI Interrupt 0000:00:1f.1[C] -> GSI 16 (level, low) -> IRQ 20
ahci 0000:00:1f.2: resuming
ACPI (acpi_bus-0192): Device `SATA]is not power manageable [20060310]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: Enable interrupts
ata2: Can't start DMA engine (-1)
i801_smbus 0000:00:1f.3: resuming
e1000 0000:02:00.0: resuming
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:02:00.0 to 64
ath_pci 0000:03:00.0: resuming
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:03:00.0 to 64
yenta_cardbus 0000:15:00.0: resuming
PM: Writing back config space on device 0000:15:00.0 at offset 1 (was 2100003, writing 2100007)
ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 20
ohci1394 0000:15:00.1: resuming
ACPI: PCI Interrupt 0000:15:00.1[B] -> GSI 17 (level, low) -> IRQ 21
sdhci 0000:15:00.2: resuming
PM: Writing back config space on device 0000:15:00.2 at offset 1 (was 2100000, writing 2100002)
PM: Writing back config space on device 0000:15:00.2 at offset 4 (was 0, writing e4301800)
ACPI: PCI Interrupt 0000:15:00.2[C] -> GSI 18 (level, low) -> IRQ 22
system 00:00: resuming
00:01: resuming
system 00:02: resuming
00:03: resuming
00:04: resuming
00:05: resuming
00:06: resuming
00:07: resuming
i8042 kbd 00:08: resuming
pnp: Device 00:08 does not support activation.
i8042 aux 00:09: resuming
pnp: Device 00:09 does not support activation.
00:0a: resuming
00:0b: resuming
pcspkr pcspkr: resuming
0000:00:1c.0:pcie00: resuming
0000:00:1c.0:pcie02: resuming
0000:00:1c.1:pcie00: resuming
0000:00:1c.1:pcie02: resuming
0000:00:1c.2:pcie00: resuming
0000:00:1c.2:pcie02: resuming
0000:00:1c.3:pcie00: resuming
0000:00:1c.3:pcie02: resuming
vesafb.0: resuming
serial8250 serial8250: resuming
i8042 i8042: resuming
psmouse serio0: resuming
atkbd serio1: resuming
sd 0:0:0:0: resuming
ata1.00: configured for UDMA/100
usb usb5: resuming
hub 5-0:1.0: resuming
mmcblk mmc0:a95c: resuming
Restarting tasks... done
Thawing cpus ...
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c04af000 soft=c048f000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3657.71 BogoMIPS (lpj=7315435)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU T2400 @ 1.83GHz stepping 08
APIC error on CPU1: 00(40)
CPU1 is up
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
PM: Adding info for usb:usb1
usb usb1: configuration #1 chosen from 1 choice
PM: Adding info for usb:1-0:1.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001840
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
PM: Adding info for usb:usb2
usb usb2: configuration #1 chosen from 1 choice
PM: Adding info for usb:2-0:1.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 22, io base 0x00001860
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
PM: Adding info for usb:usb3
usb usb3: configuration #1 chosen from 1 choice
PM: Adding info for usb:3-0:1.0
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x00001880
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.17-rc5-mm2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
PM: Adding info for usb:usb4
usb usb4: configuration #1 chosen from 1 choice
PM: Adding info for usb:4-0:1.0
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 4-2: new full speed USB device using uhci_hcd and address 2
usb 4-2: new device found, idVendor=0483, idProduct=2016
usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: Biometric Coprocessor
usb 4-2: Manufacturer: STMicroelectronics
PM: Adding info for usb:4-2
usb 4-2: configuration #1 chosen from 1 choice
PM: Adding info for usb:4-2:1.0
\
 
 \ /
  Last update: 2006-06-03 00:54    [W:0.099 / U:4.668 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site