Messages in this thread | | | From | cyril canovas <> | Subject | PROBLEM: BAD RAM SIZE DETECTION ON DELL POWER EDGE SC420 | Date | Thu, 1 Jun 2006 16:21:07 +0200 |
| |
Hello,
Linux can't manage to detect 4Go Ram but detects 3495616 kB of Ram, on a Dell Power Edge SC420 Bios Release A02
cat /proc/meminfo
MemTotal: 3495616 kB MemFree: 1650692 kB Buffers: 18700 kB Cached: 1602352 kB SwapCached: 0 kB Active: 1360888 kB Inactive: 402900 kB HighTotal: 2611760 kB HighFree: 821656 kB LowTotal: 883856 kB LowFree: 829036 kB SwapTotal: 4192956 kB SwapFree: 4192956 kB Dirty: 432 kB Writeback: 0 kB Mapped: 1292284 kB Slab: 28568 kB CommitLimit: 5940764 kB Committed_AS: 504284 kB PageTables: 3520 kB VmallocTotal: 114680 kB VmallocUsed: 10512 kB VmallocChunk: 103868 kB HugePages_Total: 0 HugePages_Free: 0 Hugepagesize: 4096 kB
dmesg
Linux version 2.6.16-gentoo-r7 (root@localhost) (version gcc 3.4.5 (Gentoo 3.4.5 -r1, ssp-3.4.5-1.0, pie-8.7.9)) #8 SMP PREEMPT Fri May 19 13:39:55 CEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000d768cc00 (usable) BIOS-e820: 00000000d768cc00 - 00000000d768ec00 (ACPI NVS) BIOS-e820: 00000000d768ec00 - 00000000d7690c00 (ACPI data) BIOS-e820: 00000000d7690c00 - 00000000d8000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 2550MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000fe710 On node 0 totalpages: 882316 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 652940 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000fec00 ACPI: RSDT (v001 DELL PESC420 0x00000007 ASL 0x00000061) @ 0x000fcc76 ACPI: FADT (v001 DELL PESC420 0x00000007 ASL 0x00000061) @ 0x000fccb2 ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffd1800 ACPI: MADT (v001 DELL PESC420 0x00000007 ASL 0x00000061) @ 0x000fcd26 ACPI: BOOT (v001 DELL PESC420 0x00000007 ASL 0x00000061) @ 0x000fcdb8 ACPI: MCFG (v001 DELL PESC420 0x00000007 ASL 0x00000061) @ 0x000fcde0 ACPI: HPET (v001 DELL PESC420 0x00000007 ASL 0x00000061) @ 0x000fce1e ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] disabled) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x07] disabled) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x03] disabled) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x05] disabled) ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at f1000000 (gap: f0000000:0ec00000) Built 1 zonelists Kernel command line: ro root=/dev/sda4 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 3494548k/3529264k available (3122k kernel code, 33596k reserved, 1041k d ata, 332k init, 2611760k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Using HPET for base-timer Using HPET for gettimeofday Detected 2793.100 MHz processor. Using hpet for high-res timesource Calibrating delay using timer specific routine.. 5592.08 BogoMIPS (lpj=11184160) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00100000 00000000 00000000 0000441d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00100000 00000000 00000000 0000441d 0 0000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00100000 00000000 00000180 0000441d 0000000 0 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Checking 'hlt' instruction... OK. CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5586.11 BogoMIPS (lpj=11172223) CPU: After generic identify, caps: bfebfbff 00100000 00000000 00000000 0000441d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00100000 00000000 00000000 0000441d 0 0000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00100000 00000000 00000180 0000441d 0000000 0 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01 Total of 2 processors activated (11178.19 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=4000 NET: Registered protocol family 16 EISA bus registered ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb32b, last bus=4 PCI: Using MMCONFIG ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:00:02.0 PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15) Linux Plug and Play Support v0.97 (c) Adam Belay Generic PHY: Registered new driver SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: dfe00000-dfefffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: dfd00000-dfdfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: disabled. MEM window: dfc00000-dfcfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1c.1 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 Simple Boot Flag at 0x7a set to 0x1 Machine check exception polling timer started. IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com> audit: initializing netlink socket (disabled) audit(1149169952.328:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 fuse init (API version 7.6) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] lp: driver loaded but no devices found Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy Non-volatile memory driver v1.2 ppdev: user-space parallel port driver Linux agpgart interface v0.101 (c) Dave Jones [drm] Initialized drm 1.0.1 20051102 vesafb: Intel Corporation, Intel(r)CopperRiver Graphics Controller, Hardware Ver sion 0.0 (OEM: Intel(r)CopperRiver Graphics Chip Accelerated VGA BIOS) vesafb: VBE version: 3.0 vesafb: VBIOS/hardware supports DDC2 transfers vesafb: no monitor limits have been set vesafb: scrolling: redraw Console: switching to colour frame buffer device 100x37 vesafb: framebuffer at 0xf0000000, mapped to 0xf8880000, using 7872k, total 7872 k fb0: VESA VGA frame buffer device ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [VBTN] isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected lp0: using parport0 (polling). mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 input: PC Speaker as /class/input/input1 Floppy drive(s): fd0 is 1.44M input: ImPS/2 Generic Wheel Mouse as /class/input/input2 floppy0: no floppy controllers found loop: loaded (max 8 devices) nbd: registered device at major 43 Intel(R) PRO/1000 Network Driver - version 6.3.9-k4-NAPI Copyright (c) 1999-2005 Intel Corporation. tg3.c:v3.49 (Feb 2, 2006) ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:02:00.0 to 64 eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base T Ethernet 00:13:20:55:c2:12 eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] Marvell 88E1101: Registered new driver Davicom DM9161E: Registered new driver Davicom DM9131: Registered new driver Cicada Cis8204: Registered new driver LXT970: Registered new driver LXT971: Registered new driver QS6612: Registered new driver Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH6: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169 ICH6: chipset revision 3 ICH6: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... hda: GCR-8483B, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: ATAPI 48X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide iscsi: registered transport (tcp) GDT-HA: Storage RAID Controller Driver. Version: 3.04 GDT-HA: Found 0 PCI Storage RAID Controllers libata version 1.20 loaded. ahci 0000:00:1f.2: version 1.2 ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl IDE mode ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part ata1: SATA max UDMA/133 cmd 0xF8806D00 ctl 0x0 bmdma 0x0 irq 217 ata2: SATA max UDMA/133 cmd 0xF8806D80 ctl 0x0 bmdma 0x0 irq 217 ata3: SATA max UDMA/133 cmd 0xF8806E00 ctl 0x0 bmdma 0x0 irq 217 ata4: SATA max UDMA/133 cmd 0xF8806E80 ctl 0x0 bmdma 0x0 irq 217 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:7c6b 83:7b09 84:4003 85:7c69 86:3a01 87:4003 88:007f ata1: dev 0 ATA-7, max UDMA/133, 156250000 sectors: LBA ata1: dev 0 configured for UDMA/133 scsi0 : ahci ata2: SATA link up 1.5 Gbps (SStatus 113) ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f ata2: dev 0 ATA-7, max UDMA/133, 320173056 sectors: LBA48 ata2: dev 0 configured for UDMA/133 scsi1 : ahci ata3: SATA link down (SStatus 0) scsi2 : ahci ata4: SATA link down (SStatus 0) scsi3 : ahci Vendor: ATA Model: Maxtor 6Y080M0 Rev: YAR5 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: Maxtor 6L160M0 Rev: BACE Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 320173056 512-byte hdwr sectors (163929 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 320173056 512-byte hdwr sectors (163929 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sd 1:0:0:0: Attached scsi disk sdb sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 ieee1394: Initialized config rom entry `ip1394' usbmon: debugfs is not available ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: irq 225, io mem 0xffa80800 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver usbcore: registered new driver libusual EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 2 Cannot allocate resource for EISA slot 5 Cannot allocate resource for EISA slot 6 EISA: Detected 0 cards. dcdbas: Dell Systems Management Base Driver (version 5.6.0-2) NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Starting balanced_irq Using IPI Shortcut mode kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 332k freed Adding 4192956k swap on /dev/sda3. Priority:-1 extents:1 across:4192956k EXT3 FS on sda4, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sdb1, internal journal EXT3-fs: mounted filesystem with ordered data mode. USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 225, io base 0x0000ff80 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 233 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 233, io base 0x0000ff60 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 50, io base 0x0000ff40 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 58, io base 0x0000ff20 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. vmmon: module license 'unspecified' taints kernel. /dev/vmmon[8215]: Module vmmon: registered with major=10 minor=165 /dev/vmmon[8215]: Module vmmon: initialized /dev/vmnet: open called by PID 8262 (vmnet-bridge) /dev/vmnet: hub 0 does not exist, allocating memory. /dev/vmnet: port on hub 0 successfully opened bridge-eth0: enabling the bridge bridge-eth0: up bridge-eth0: already up bridge-eth0: attached mtrr: no more MTRRs available mtrr: no more MTRRs available mtrr: no more MTRRs available mtrr: no more MTRRs available /dev/vmnet: open called by PID 8971 (vmware-vmx) device eth0 entered promiscuous mode bridge-eth0: enabled promiscuous mode /dev/vmnet: port on hub 0 successfully opened /dev/vmmon[8983]: host clock rate change request 0 -> 19 /dev/vmmon[8983]: host clock rate change request 19 -> 83 device eth0 left promiscuous mode bridge-eth0: disabled promiscuous mode /dev/vmnet: open called by PID 8984 (vmware-vmx) device eth0 entered promiscuous mode bridge-eth0: enabled promiscuous mode /dev/vmnet: port on hub 0 successfully opened
-- SARL EGNX 323 Chemin de l'oratoire BP 116 13120 Gardanne
Site internet www.egnx.com Tél 04 42 12 69 02 Fax 01 41 30 88 95 Mob 06 20 58 63 69
Email cyril@egnx.com ICQ 39077836
Mr Canovas Cyril Responsable Technique - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |