lkml.org 
[lkml]   [2006]   [Apr]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: Lock-up with modprobe sdhci after suspending to ram
Date
Pierre Ossman kirjoitti viestissään (lähetysaika tiistai, 25. huhtikuuta 2006 
11:42):
> Jani-Matti Hätinen wrote:
> > Looks like some kind of routing problem. Even pings don't seem to get
> > through to mmc.drzeus.cx, or list.drzeus.cx. With http I get a timeout
> > from mmc.drzeus.cx. This is from IP 80.221.18.58
>
> Most of the domain is down right now (changing ISP). But the mail server
> is up at hermes.drzeus.cx:

Ok. That explains it.

> > Unfortunately even text mode is completely speechless about it. The
> > modprobe goes through cleanly and I get the regular prompt (with a
> > blinking cursor even), but the machine's completely locked up.
>
> Have you tried pinging it? For some reason the keyboard tends to bail
> out when there are outstanding MMC requests. I've only seen this with a
> card in the slot though.

Yes, but the thing is deader than the cat I'm sitting on. Even SysRq is dead.

> You could increase the log level sent to console and enable MMC_DEBUG.
> If you can find more closely where it hangs I have a better chance of
> finding it.

Ok, this is what I get on Loglevel 9.
If I try to suspend with the module loaded and with a card in the reader I
get:
Stopping tasks: ================================|
ipw2200: Failed to send CARD_DISABLE: Command timed out
ACPI: PCI interrupt for device 0000:01:05.0 disabled
sdhci [sdhci_suspend()]: Suspending...
MMC: starting cmd 07 arg 00000000 flags 00000000
sdhci [sdhci_send_command()]: Sending cmd (7)

And if I modprobe sdhci after suspend&resume I get the following:
First from the modprobe (not all of it is visible):
sdhci: Sys addr: 0xffffffff | Version: 0x0000ffff
sdhci: Blk size: 0x0000ffff | Blk cnt: 0x0000ffff
sdhci: Argument: 0xffffffff | Trn mode: 0x0000ffff
sdhci: Present: 0xffffffff | Host ctl: 0x000000ff
sdhci: Power: 0x000000ff | Blk gap: 0x000000ff
sdhci: Wake-up: 0x000000ff | Clock: 0x0000ffff
sdhci: Timeout: 0x000000ff | Int stat: 0xffffffff
sdhci: Int enab: 0xffffffff | Sig enab: 0xffffffff
sdhci: AC12 err: 0x0000ffff | Slot int: 0x0000ffff
sdhci: Caps: 0xffffffff | Max curr: 0xffffffff
sdhci: ===========================================
kobject mmc0: registering. parent: mmc_host, set: class_obj
kobject_uevent
fill_kobj_path: path = '/class/mmc_host/mmc0'
fill_kobj_path: path = '/devices/pci0000:00/0000:00:1e.0/0000:01:03.2'
sdhci [sdhci_set_ios()]: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0
mmc0: SDHCI at 0xfe8fe000 irq 18 PIO
sdhci [sdhci_set_ios()]: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0

Plus a prompt and:
sdhci [sdhci_set_ios()]: clock 246093Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0
sdhci [sdhci_set_ios()]: clock 246093Hz busmode 1 powermode 2 cs 1 Vdd 21
width 0
MMC: starting cmd 00 arg 00000000 flags 00000040
sdhci [sdhci_send_command()]: Sending cmd (0)

Whereas, if I modprobe sdhci in a fresh boot I get:
kobject sdhci: registering. parent: <NULL>, set: module
kobject_uevent
fill_kobj_path: path = '/module/sdhci'
sdhci: Secure Digital Host Controller Interface driver, 0.11
sdhci: Copyright(c) Pierre Ossman
kobject sdhci: registering. parent: <NULL>, set: drivers
kobject_uevent
fill_kobj_path: path = '/bus/pci/drivers/sdhci'
sdhci [sdhci_probe()]: found at 0000:01:03.2
sdhci [sdhci_probe()]: found 1 slot(s)
ACPI: PCI Interrupt 0000:01:03.2[C] -> GSI 20 (level, low) -> IRQ 18
sdhci [sdhci_probe_slot()]: slot 0 at 0xfe8fe000, irq 18
sdhci: ============== REGISTER DUMP ==============
sdhci: Sys addr: 0x00000000 | Version: 0x00000200
sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci: Present: 0x01f20000 | Host ctl: 0x00000000
sdhci: Power: 0x00000000 | Blk gap: 0x00000000
sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
sdhci: Timeout: 0x0000000e | Int stat: 0x00000000
sdhci: Int enab: 0xe1ff00cf | Sig enab: 0xe1ff00cf
sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci: Caps: 0x018021a1 | Max curr: 0x00000040
kobject mmc0: registering. parent: mmc_host, set: class_obj
kobject_uevent
fill_kobj_path: path = '/class/mmc_host/mmc0'
fill_kobj_path: path = '/devices/pci0000:00/0000:00:1e.0/0000:01:03.2'
sdhci [sdhci_set_ios()]: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0
mmc0: SDHCI at 0xfe8fe000 irq 18 PIO
sdhci [sdhci_set_ios()]: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0
sdhci [sdhci_set_ios()]: clock 128906Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0
sdhci [sdhci_set_ios()]: clock 128906Hz busmode 1 powermode 2 cs 1 Vdd 21
width 0

Plus a prompt and:
MMC: starting cmd 00 arg 00000000 flags 00000040
sdhci [sdhci_tasklet_finish()]: Ending request, cmd (0)
MMC: req done (00): 1: 00000000 00000000 00000000 00000000
sdhci [sdhci_set_ios()]: clock 128906Hz busmode 1 powermode 2 cs 0 Vdd 21
width 0
MMC: starting cmd 37 arg 00000000 flags 00000015
sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37)
MMC: req done (37): 1: 00000000 00000000 00000000 00000000
MMC: starting cmd 37 arg 00000000 flags 00000015
sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37)
MMC: req done (37): 1: 00000000 00000000 00000000 00000000
MMC: starting cmd 37 arg 00000000 flags 00000015
sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37)
MMC: req done (37): 1: 00000000 00000000 00000000 00000000
MMC: starting cmd 37 arg 00000000 flags 00000015
sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37)
MMC: req done (37): 1: 00000000 00000000 00000000 00000000
MMC: starting cmd 01 arg 00000000 flags 00000061
sdhci [sdhci_tasklet_finish()]: Ending request, cmd (1)
MMC: req done (01): 1: 00000000 00000000 00000000 00000000
sdhci [sdhci_set_ios()]: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0

So for some reason suspend&resume seems to screw up the registers and double
the clock speed.
Also I just noticed that if the machine has been through at least one
suspend&resume cycle, rebooting no longer works. All processes exit cleanly,
but the system just hangs when it should shut down.
So it seems quite likely that suspend&resume doesn't really work the way it
should in this machine (Asus S5A notebook) and sdhci triggers the problem.

--
Jani-Matti Hätinen
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2006-04-25 15:48    [W:0.084 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site