lkml.org 
[lkml]   [2006]   [Mar]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 2.6.16-mm1 3/3] rtc: add support for m41t81 & m41t85 chips to m41t00 driver
Hi Jean,

On Tue, Mar 28, 2006 at 05:54:50PM +0200, Jean Delvare wrote:
> Hi Mark,
>
> Some more comments, sorry for being slow.

You're not slow at all. No worries.

> > drivers/i2c/chips/m41t00.c | 294 ++++++++++++++++++++++++++++++++++-----------
> > include/linux/m41t00.h | 50 +++++++
>
> Who else is going to use this header file? It's rather rare to have a
> hardware-specific header file under include/linux.

The platform-specific code for any platform that uses that rtc will need
to include that header file so it can pass the platform data to the rtc
driver. I have a patch for arch/ppc/platforms/katana.c but I haven't
submitted it b/c of the ppc->powerpc merge that's going on right now.
I will get it in there once I've moved the katana code into the merged tree.
There is a lot of work before that happens, though.

> > diff -Nurp linux-2.6.16-mm1-cleanup/drivers/i2c/chips/m41t00.c linux-2.6.16-mm1-newsupp/drivers/i2c/chips/m41t00.c
> > --- linux-2.6.16-mm1-cleanup/drivers/i2c/chips/m41t00.c 2006-03-27 16:00:35.000000000 -0700
> > +++ linux-2.6.16-mm1-newsupp/drivers/i2c/chips/m41t00.c 2006-03-27 16:49:35.000000000 -0700
> > (...)
> > static unsigned short ignore[] = { I2C_CLIENT_END };
> > -static unsigned short normal_addr[] = { 0x68, I2C_CLIENT_END };
> > +static unsigned short normal_addr[] = { 0, I2C_CLIENT_END };
>
> Bad idea. If no platform data is found, the driver will attempt to
> probe I2C address 0, which is a broadcast address. I can predict
> interesting results ;)
>
> So, if you don't want the driver to do anything in the absence of
> platform data, you should define normal_addr the following way:

If there is no platform data, m41t00_platform_probe() should return
-ENODEV and make m41t00_init() causing the driver to not become active.
I've tested that, actually, and it seems to work.

> static unsigned short normal_addr[] = { I2C_CLIENT_END, I2C_CLIENT_END };

Hrm, that's a good idea. I'll do that, even though it shouldn't be
necessary.

> > +struct m41t00_chip_info {
> > + u16 type;
> > + u16 read_limit;
> > + u8 sec; /* Offsets for chip regs */
> > + u8 min;
> > + u8 hour;
> > + u8 day;
> > + u8 mon;
> > + u8 year;
> > + u8 alarm_mon;
> > + u8 alarm_hour;
> > + u8 sqw;
> > + u32 sqw_freq;
> > +};
>
> u16 is probably overkill for .type and .read_limit.

Yeah, probably. I'll change them to u8.

> > +static struct m41t00_chip_info m41t00_chip_info_tbl[] = {
> > + { M41T00_TYPE_M41T00, 5, 0, 1, 2, 4, 5, 6, 0, 0, 0, 0 },
> > + { M41T00_TYPE_M41T81, 1, 1, 2, 3, 5, 6, 7, 0xa, 0xc, 0x13, 0 },
> > + { M41T00_TYPE_M41T85, 1, 1, 2, 3, 5, 6, 7, 0xa, 0xc, 0x13, 0 },
> > +};
>
> C99-style initialization, please? It'll take much more lines, granted,
> but is also way more robust to future changes, and will be more
> readable too.

Well, the struct is right there so I figured the chances of changing the
struct and not seeing that the compile-time init code needs to be
changed too was small. I guess its better to be safe than sorry and it
does make it more readable so I'll change it.

> May I ask why you define separate types for the M41T81 and the M41T85,
> when you handle both exactly the same way?

The only reason is so that its obvious that both the t81 and t85 are
supported. If I make it M41T81 only then I can easily see someone
grep'ing around looking for M41T85, not finding it, and writing their
own driver. I don't see any harm in having both, do you?

> > + sec = buf[m41t00_chip->sec] & 0x7f;
> > + min = buf[m41t00_chip->min] & 0x7f;
> > + hour = buf[m41t00_chip->hour] & 0x3f;
> > + day = buf[m41t00_chip->day] & 0x3f;
> > + mon = buf[m41t00_chip->mon] & 0x1f;
> > + year = buf[m41t00_chip->year] & 0xff;
>
> The year masking is a no-op, you could omit it.

Yes.

> > @@ -169,24 +246,100 @@ m41t00_probe(struct i2c_adapter *adap, i
> > {
> > struct i2c_client *client;
> > int rc;
> > + u8 rbuf[1], wbuf[2], msgbuf[1] = { 0 }; /* offset into rtc's regs */
> > + struct i2c_msg msgs[] = {
> > + {
> > + .addr = 0,
> > + .flags = 0,
> > + .len = 1,
> > + .buf = msgbuf,
> > + },
> > + {
> > + .addr = 0,
> > + .flags = I2C_M_RD,
> > + .len = 1,
> > + .buf = rbuf,
> > + },
> > + };
>
> Why don't you initialize both .addr right away?

Actually, I already init the .addr field right away so I'll remove them
from them from the code above.

> >
> > client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
> > if (!client)
> > return -ENOMEM;
> >
> > - strlcpy(client->name, M41T00_DRV_NAME, I2C_NAME_SIZE);
> > + strlcpy(client->name, m41t00_driver.driver.name, I2C_NAME_SIZE);
>
> The driver name may not be suitable here, the client name should
> instead reflect what chip it is.

Ah, good one.

> > + if (m41t00_chip->type != M41T00_TYPE_M41T00) {
> > + /* If asked, set SQW frequency & enable */
> > + if (m41t00_chip->sqw_freq) {
> > + msgbuf[0] = m41t00_chip->alarm_mon;
> > + if ((rc = i2c_transfer(client->adapter, msgs, 2)) < 0)
> > + goto sqw_err;
>
> You did not check whether the adapter you are attaching to supports this
> kind of transaction! You need to call i2c_check_functionality, see how
> other i2c chip drivers (for example ds1337) are doing. For i2c_transfer
> and i2c_master_send, you want to check for I2C_FUNC_I2C.

Okay.

> > +
> > + wbuf[0] = m41t00_chip->alarm_mon;
> > + wbuf[1] = rbuf[0] & ~0x40;
> > + if ((rc = i2c_master_send(client, wbuf, 2)) < 0)
> > + goto sqw_err;
> > +
> > + wbuf[0] = m41t00_chip->sqw;
> > + wbuf[1] = m41t00_chip->sqw_freq;
> > + if ((rc = i2c_master_send(client, wbuf, 2)) < 0)
> > + goto sqw_err;
> > +
> > + wbuf[0] = m41t00_chip->alarm_mon;
> > + wbuf[1] = rbuf[0] | 0x40;
> > + if ((rc = i2c_master_send(client, wbuf, 2)) < 0)
> > + goto sqw_err;
> > + }
> > +
> > + /* Make sure HT (Halt Update) bit is cleared */
> > + msgbuf[0] = m41t00_chip->alarm_hour;
> > + if ((rc = i2c_transfer(client->adapter, msgs, 2)) < 0)
> > + goto ht_err;
> > +
> > + if (rbuf[0] & 0x40) {
> > + wbuf[0] = m41t00_chip->alarm_hour;
> > + wbuf[1] = rbuf[0] & ~0x40;
> > + if ((rc = i2c_master_send(client, wbuf, 2)) < 0)
> > + goto ht_err;
> > + }
> > + }
> > +
> > + /* Make sure ST (stop) bit is cleared */
> > + msgbuf[0] = m41t00_chip->sec;
> > + if ((rc = i2c_transfer(client->adapter, msgs, 2)) < 0)
> > + goto st_err;
> > +
> > + if (rbuf[0] & 0x80) {
> > + wbuf[0] = m41t00_chip->sec;
> > + wbuf[1] = rbuf[0] & ~0x80;
> > + if ((rc = i2c_master_send(client, wbuf, 2)) < 0)
> > + goto st_err;
> > }
>
> What you do here are basically SMBus Read Byte and SMBus Write Byte
> transactions. The code would be much more simple if you were using the
> i2c_smbus_read_byte_data and i2c_smbus_write_byte_data functions, which
> take care of all the technical details.

That's true but I assumed that since I was using i2c_transfer
earlier, I should use it here. Is that a bad assumption?
I do see that ds1337.c uses both types.

> > +st_err:
> > + dev_err(&client->dev, "m41t00_probe: Can't clear ST bit\n");
> > + goto attach_err;
> > +ht_err:
> > + dev_err(&client->dev, "m41t00_probe: Can't clear HT bit\n");
> > + goto attach_err;
> > +sqw_err:
> > + dev_err(&client->dev, "m41t00_probe: Can't set SQW Frequency\n");
> > +attach_err:
> > + kfree(client);
> > + return rc;
> > }
>
> Mrghh, this isn't exactly elegant... You should be able to make it
> better if you switch to i2c_smbus_read/write_byte_data as suggested.

Yep.

> > diff -Nurp linux-2.6.16-mm1-cleanup/include/linux/m41t00.h linux-2.6.16-mm1-newsupp/include/linux/m41t00.h
> > --- linux-2.6.16-mm1-cleanup/include/linux/m41t00.h 1969-12-31 17:00:00.000000000 -0700
> > +++ linux-2.6.16-mm1-newsupp/include/linux/m41t00.h 2006-03-27 16:25:51.000000000 -0700
> > @@ -0,0 +1,50 @@
> > +/*
> > + * Definitions for the ST M41T00 family of i2c rtc chips.
> > + *
> > + * Author: Mark A. Greer <mgreer@mvista.com>
> > + *
> > + * 2005 (c) MontaVista Software, Inc. This file is licensed under
>
> We're in year 2006 now :)

Yes, but my understanding is that I should leave the 2005 there b/c that
file was already copyrighted with that year. I could do a "2005, 2006"
if you like.

> > + * the terms of the GNU General Public License version 2. This program
> > + * is licensed "as is" without any warranty of any kind, whether express
> > + * or implied.
> > + */
> > +
> > +#ifndef _M41T00_H
> > +#define _M41T00_H
> > +
> > +#define M41T00_DRV_NAME "m41t00"
>
> Why do you need to export this?

Because the code that passes the platform_data needs to put that name
in the data so that the driver can find it. That's the value that the
driver uses to search for its platform_data. I'll attach the patch to
the platform code that I used to test it so you can see what I mean.
Its at the end of this email.

> > +#define M41T00_I2C_ADDR 0x68
>
> Not used anywhere?

Yes, in the platform code.

> > +#define M41T00_TYPE_M41T00 0
> > +#define M41T00_TYPE_M41T81 81
> > +#define M41T00_TYPE_M41T85 85
>
> The i2c core has a facility for drivers supporting several types of
> devices. Check for I2C_CLIENT_INSMOD_3() in your case. The advantage if
> you go that way is that chip types can be set from userspace through
> module parameters, which may be convenient for testing when adding
> support for new platforms.

Okay, I'll take a look.

> > +/* SQW output disabled, this is default value by power on*/
> > +#define SQW_FREQ_DISABLE (0)
> > +
> > +#define SQW_FREQ_32KHZ (1<<4) /* 32.768 KHz */
> > +#define SQW_FREQ_8KHZ (2<<4) /* 8.192 KHz */
> > +#define SQW_FREQ_4KHZ (3<<4) /* 4.096 KHz */
> > +#define SQW_FREQ_2KHZ (4<<4) /* 2.048 KHz */
> > +#define SQW_FREQ_1KHZ (5<<4) /* 1.024 KHz */
> > +#define SQW_FREQ_512HZ (6<<4) /* 512 Hz */
> > +#define SQW_FREQ_256HZ (7<<4) /* 256 Hz */
> > +#define SQW_FREQ_128HZ (8<<4) /* 128 Hz */
> > +#define SQW_FREQ_64HZ (9<<4) /* 64 Hz */
> > +#define SQW_FREQ_32HZ (10<<4) /* 32 Hz */
> > +#define SQW_FREQ_16HZ (11<<4) /* 16 Hz */
> > +#define SQW_FREQ_8HZ (12<<4) /* 8 Hz */
> > +#define SQW_FREQ_4HZ (13<<4) /* 4 Hz */
> > +#define SQW_FREQ_2HZ (14<<4) /* 2 Hz */
> > +#define SQW_FREQ_1HZ (15<<4) /* 1 Hz */
>
> Not used anywhere either?

Platform code can pass one of these values into the driver via
platform_data (if its a t81 or t85, not needed for the t00).

> > +extern ulong m41t00_get_rtc_time(void);
> > +extern int m41t00_set_rtc_time(ulong nowtime);
>
> Hopefully you won't have to export these anymore after you move to the
> new RTC subsystem. But that's a different story. In the meantime,
> shouldn't you have EXPORT_SYMBOL_GPL() for these functions? Else
> compiling m41t00 as a module won't work.

Good point. Will fix.

Below is the katana patch. Basically, it adds the platform_data
required for the m41t00 rtc which the m41t00 driver later takes out.
Note that the m41t00 doesn't need the sqw_freq value so you won't see
it being set in this patch.

I did have a couple questions above so I'll wait for your response
and then make a new patch.

Thanks for your time, Jean.

Mark
---

diff -Nurp linux-2.6.16-mm1-cleanup/arch/ppc/platforms/katana.c linux-2.6.16-mm1-newsupp/arch/ppc/platforms/katana.c
--- linux-2.6.16-mm1-cleanup/arch/ppc/platforms/katana.c 2006-03-23 16:15:22.000000000 -0700
+++ linux-2.6.16-mm1-newsupp/arch/ppc/platforms/katana.c 2006-03-23 17:37:46.000000000 -0700
@@ -28,6 +28,7 @@
#include <linux/mtd/physmap.h>
#include <linux/mv643xx.h>
#include <linux/platform_device.h>
+#include <linux/m41t00.h>
#ifdef CONFIG_BOOTIMG
#include <linux/bootimg.h>
#endif
@@ -843,8 +844,31 @@ katana_find_end_of_memory(void)
}

#if defined(CONFIG_I2C_MV64XXX) && defined(CONFIG_SENSORS_M41T00)
-extern ulong m41t00_get_rtc_time(void);
-extern int m41t00_set_rtc_time(ulong);
+static struct m41t00_platform_data katana_m41t00_pdata = {
+ .type = M41T00_TYPE_M41T00,
+ .i2c_addr = M41T00_I2C_ADDR,
+};
+
+static struct platform_device katana_m41t00_pdev = {
+ .name = M41T00_DRV_NAME,
+ .id = 0,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &katana_m41t00_pdata,
+ },
+};
+
+static int __init
+katana_add_pdata(void)
+{
+ int rc;
+
+ if ((rc = platform_device_register(&katana_m41t00_pdev)))
+ platform_device_unregister(&katana_m41t00_pdev);
+
+ return rc;
+}
+arch_initcall(katana_add_pdata);

static int __init
katana_rtc_hookup(void)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2006-03-28 20:13    [W:0.054 / U:6.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site