lkml.org 
[lkml]   [2006]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH][resend] PNX8550 UART driver
This patch adds UART support for PNX8330/8550/8950 Philips MIPS-based SoCs.
Should be applied together with the PNX UART header fixup patch last sent yesterday (http://lkml.org/lkml/2006/12/7/147). This stuff has been basically approved by rmk before he quitted maintaining serial core but hasn't been accepted yet due to merge window miss at that moment.

drivers/serial/Kconfig | 16
drivers/serial/Makefile | 1
drivers/serial/pnx8xxx_uart.c | 853 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 870 insertions(+)

Signed-off-by: Vitaly Wool <vitalywool@gmail.com>

Index: linux-2.6/drivers/serial/Kconfig
===================================================================
--- linux-2.6.orig/drivers/serial/Kconfig 2006-12-08 16:08:11.000000000 +0300
+++ linux-2.6/drivers/serial/Kconfig 2006-12-08 18:00:00.000000000 +0300
@@ -687,6 +687,22 @@
depends on SERIAL_SH_SCI=y
select SERIAL_CORE_CONSOLE

+config SERIAL_PNX8XXX
+ bool "Enable PNX8XXX SoCs' UART Support"
+ depends on MIPS && SOC_PNX8550
+ select SERIAL_CORE
+ help
+ If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
+ and you want to use serial ports, say Y. Otherwise, say N.
+
+config SERIAL_PNX8XXX_CONSOLE
+ bool "Enable PNX8XX0 serial console"
+ depends on SERIAL_PNX8XXX
+ select SERIAL_CORE_CONSOLE
+ help
+ If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
+ and you want to use serial console, say Y. Otherwise, say N.
+
config SERIAL_CORE
tristate

Index: linux-2.6/drivers/serial/pnx8xxx_uart.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-2.6/drivers/serial/pnx8xxx_uart.c 2006-12-08 18:00:31.000000000 +0300
@@ -0,0 +1,853 @@
+/*
+ * UART driver for PNX8XXX SoCs
+ *
+ * Author: Per Hallsmark per.hallsmark@mvista.com
+ * Ported to 2.6 kernel by EmbeddedAlley
+ * Reworked by Vitaly Wool <vitalywool@gmail.com>
+ *
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ * Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of
+ * any kind, whether express or implied.
+ *
+ */
+
+#if defined(CONFIG_SERIAL_PNX8XXX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/serial_pnx8xxx.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+/* We'll be using StrongARM sa1100 serial port major/minor */
+#define SERIAL_PNX8XXX_MAJOR 204
+#define MINOR_START 5
+
+#define NR_PORTS 2
+
+#define PNX8XXX_ISR_PASS_LIMIT 256
+
+/*
+ * Convert from ignore_status_mask or read_status_mask to FIFO
+ * and interrupt status bits
+ */
+#define SM_TO_FIFO(x) ((x) >> 10)
+#define SM_TO_ISTAT(x) ((x) & 0x000001ff)
+#define FIFO_TO_SM(x) ((x) << 10)
+#define ISTAT_TO_SM(x) ((x) & 0x000001ff)
+
+/*
+ * This is the size of our serial port register set.
+ */
+#define UART_PORT_SIZE 0x1000
+
+/*
+ * This determines how often we check the modem status signals
+ * for any change. They generally aren't connected to an IRQ
+ * so we have to poll them. We also check immediately before
+ * filling the TX fifo incase CTS has been dropped.
+ */
+#define MCTRL_TIMEOUT (250*HZ/1000)
+
+extern struct pnx8xxx_port pnx8xxx_ports[];
+
+static inline int serial_in(struct pnx8xxx_port *sport, int offset)
+{
+ return (__raw_readl(sport->port.membase + offset));
+}
+
+static inline void serial_out(struct pnx8xxx_port *sport, int offset, int value)
+{
+ __raw_writel(value, sport->port.membase + offset);
+}
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void pnx8xxx_mctrl_check(struct pnx8xxx_port *sport)
+{
+ unsigned int status, changed;
+
+ status = sport->port.ops->get_mctrl(&sport->port);
+ changed = status ^ sport->old_status;
+
+ if (changed == 0)
+ return;
+
+ sport->old_status = status;
+
+ if (changed & TIOCM_RI)
+ sport->port.icount.rng++;
+ if (changed & TIOCM_DSR)
+ sport->port.icount.dsr++;
+ if (changed & TIOCM_CAR)
+ uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
+ if (changed & TIOCM_CTS)
+ uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
+
+ wake_up_interruptible(&sport->port.info->delta_msr_wait);
+}
+
+/*
+ * This is our per-port timeout handler, for checking the
+ * modem status signals.
+ */
+static void pnx8xxx_timeout(unsigned long data)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)data;
+ unsigned long flags;
+
+ if (sport->port.info) {
+ spin_lock_irqsave(&sport->port.lock, flags);
+ pnx8xxx_mctrl_check(sport);
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+
+ mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT);
+ }
+}
+
+/*
+ * interrupts disabled on entry
+ */
+static void pnx8xxx_stop_tx(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ u32 ien;
+
+ /* Disable TX intr */
+ ien = serial_in(sport, PNX8XXX_IEN);
+ serial_out(sport, PNX8XXX_IEN, ien & ~PNX8XXX_UART_INT_ALLTX);
+
+ /* Clear all pending TX intr */
+ serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLTX);
+}
+
+/*
+ * interrupts may not be disabled on entry
+ */
+static void pnx8xxx_start_tx(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ u32 ien;
+
+ /* Clear all pending TX intr */
+ serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLTX);
+
+ /* Enable TX intr */
+ ien = serial_in(sport, PNX8XXX_IEN);
+ serial_out(sport, PNX8XXX_IEN, ien | PNX8XXX_UART_INT_ALLTX);
+}
+
+/*
+ * Interrupts enabled
+ */
+static void pnx8xxx_stop_rx(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ u32 ien;
+
+ /* Disable RX intr */
+ ien = serial_in(sport, PNX8XXX_IEN);
+ serial_out(sport, PNX8XXX_IEN, ien & ~PNX8XXX_UART_INT_ALLRX);
+
+ /* Clear all pending RX intr */
+ serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX);
+}
+
+/*
+ * Set the modem control timer to fire immediately.
+ */
+static void pnx8xxx_enable_ms(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+
+ mod_timer(&sport->timer, jiffies);
+}
+
+static void
+pnx8xxx_rx_chars(struct pnx8xxx_port *sport, struct pt_regs *regs)
+{
+ struct tty_struct *tty = sport->port.info->tty;
+ unsigned int status, ch, flg;
+
+ status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) |
+ ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT));
+ while (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFIFO)) {
+ ch = serial_in(sport, PNX8XXX_FIFO);
+
+ sport->port.icount.rx++;
+
+ flg = TTY_NORMAL;
+
+ /*
+ * note that the error handling code is
+ * out of the main execution path
+ */
+ if (status & (FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE |
+ PNX8XXX_UART_FIFO_RXPAR) |
+ ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN))) {
+ if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR))
+ sport->port.icount.parity++;
+ else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE))
+ sport->port.icount.frame++;
+ if (status & ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN))
+ sport->port.icount.overrun++;
+
+ status &= sport->port.read_status_mask;
+
+ if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR))
+ flg = TTY_PARITY;
+ else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE))
+ flg = TTY_FRAME;
+
+#ifdef SUPPORT_SYSRQ
+ sport->port.sysrq = 0;
+#endif
+ }
+
+ if (uart_handle_sysrq_char(&sport->port, ch, regs))
+ goto ignore_char;
+
+ uart_insert_char(&sport->port, status,
+ ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN), ch, flg);
+
+ ignore_char:
+ serial_out(sport, PNX8XXX_LCR, serial_in(sport, PNX8XXX_LCR) |
+ PNX8XXX_UART_LCR_RX_NEXT);
+ status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) |
+ ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT));
+ }
+ tty_flip_buffer_push(tty);
+}
+
+static void pnx8xxx_tx_chars(struct pnx8xxx_port *sport)
+{
+ struct circ_buf *xmit = &sport->port.info->xmit;
+
+ if (sport->port.x_char) {
+ serial_out(sport, PNX8XXX_FIFO, sport->port.x_char);
+ sport->port.icount.tx++;
+ sport->port.x_char = 0;
+ return;
+ }
+
+ /*
+ * Check the modem control lines before
+ * transmitting anything.
+ */
+ pnx8xxx_mctrl_check(sport);
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
+ pnx8xxx_stop_tx(&sport->port);
+ return;
+ }
+
+ /*
+ * TX while bytes available
+ */
+ while (((serial_in(sport, PNX8XXX_FIFO) &
+ PNX8XXX_UART_FIFO_TXFIFO) >> 16) < 16) {
+ serial_out(sport, PNX8XXX_FIFO, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ sport->port.icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&sport->port);
+
+ if (uart_circ_empty(xmit))
+ pnx8xxx_stop_tx(&sport->port);
+}
+
+static irqreturn_t pnx8xxx_int(int irq, void *dev_id)
+{
+ struct pnx8xxx_port *sport = dev_id;
+ unsigned int status;
+
+ spin_lock(&sport->port.lock);
+ /* Get the interrupts */
+ status = serial_in(sport, PNX8XXX_ISTAT) & serial_in(sport, PNX8XXX_IEN);
+
+ /* Break signal received */
+ if (status & PNX8XXX_UART_INT_BREAK) {
+ sport->port.icount.brk++;
+ uart_handle_break(&sport->port);
+ }
+
+ /* Byte received */
+ if (status & PNX8XXX_UART_INT_RX)
+ pnx8xxx_rx_chars(sport, regs);
+
+ /* TX holding register empty - transmit a byte */
+ if (status & PNX8XXX_UART_INT_TX)
+ pnx8xxx_tx_chars(sport);
+
+ /* Clear the ISTAT register */
+ serial_out(sport, PNX8XXX_ICLR, status);
+
+ spin_unlock(&sport->port.lock);
+ return IRQ_HANDLED;
+}
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy.
+ */
+static unsigned int pnx8xxx_tx_empty(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+
+ return serial_in(sport, PNX8XXX_FIFO) & PNX8XXX_UART_FIFO_TXFIFO_STA ? 0 : TIOCSER_TEMT;
+}
+
+static unsigned int pnx8xxx_get_mctrl(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ unsigned int mctrl = TIOCM_DSR;
+ unsigned int msr;
+
+ /* REVISIT */
+
+ msr = serial_in(sport, PNX8XXX_MCR);
+
+ mctrl |= msr & PNX8XXX_UART_MCR_CTS ? TIOCM_CTS : 0;
+ mctrl |= msr & PNX8XXX_UART_MCR_DCD ? TIOCM_CAR : 0;
+
+ return mctrl;
+}
+
+static void pnx8xxx_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+#if 0 /* FIXME */
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ unsigned int msr;
+#endif
+}
+
+/*
+ * Interrupts always disabled.
+ */
+static void pnx8xxx_break_ctl(struct uart_port *port, int break_state)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ unsigned long flags;
+ unsigned int lcr;
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+ lcr = serial_in(sport, PNX8XXX_LCR);
+ if (break_state == -1)
+ lcr |= PNX8XXX_UART_LCR_TXBREAK;
+ else
+ lcr &= ~PNX8XXX_UART_LCR_TXBREAK;
+ serial_out(sport, PNX8XXX_LCR, lcr);
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+}
+
+static int pnx8xxx_startup(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ int retval;
+
+ /*
+ * Allocate the IRQ
+ */
+ retval = request_irq(sport->port.irq, pnx8xxx_int, 0,
+ "pnx8xxx-uart", sport);
+ if (retval)
+ return retval;
+
+ /*
+ * Finally, clear and enable interrupts
+ */
+
+ serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX |
+ PNX8XXX_UART_INT_ALLTX);
+
+ serial_out(sport, PNX8XXX_IEN, serial_in(sport, PNX8XXX_IEN) |
+ PNX8XXX_UART_INT_ALLRX |
+ PNX8XXX_UART_INT_ALLTX);
+
+ /*
+ * Enable modem status interrupts
+ */
+ spin_lock_irq(&sport->port.lock);
+ pnx8xxx_enable_ms(&sport->port);
+ spin_unlock_irq(&sport->port.lock);
+
+ return 0;
+}
+
+static void pnx8xxx_shutdown(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ int lcr;
+
+ /*
+ * Stop our timer.
+ */
+ del_timer_sync(&sport->timer);
+
+ /*
+ * Disable all interrupts
+ */
+ serial_out(sport, PNX8XXX_IEN, 0);
+
+ /*
+ * Reset the Tx and Rx FIFOS, disable the break condition
+ */
+ lcr = serial_in(sport, PNX8XXX_LCR);
+ lcr &= ~PNX8XXX_UART_LCR_TXBREAK;
+ lcr |= PNX8XXX_UART_LCR_TX_RST | PNX8XXX_UART_LCR_RX_RST;
+ serial_out(sport, PNX8XXX_LCR, lcr);
+
+ /*
+ * Clear all interrupts
+ */
+ serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX |
+ PNX8XXX_UART_INT_ALLTX);
+
+ /*
+ * Free the interrupt
+ */
+ free_irq(sport->port.irq, sport);
+}
+
+static void
+pnx8xxx_set_termios(struct uart_port *port, struct termios *termios,
+ struct termios *old)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ unsigned long flags;
+ unsigned int lcr_fcr, old_ien, baud, quot;
+ unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
+
+ /*
+ * We only support CS7 and CS8.
+ */
+ while ((termios->c_cflag & CSIZE) != CS7 &&
+ (termios->c_cflag & CSIZE) != CS8) {
+ termios->c_cflag &= ~CSIZE;
+ termios->c_cflag |= old_csize;
+ old_csize = CS8;
+ }
+
+ if ((termios->c_cflag & CSIZE) == CS8)
+ lcr_fcr = PNX8XXX_UART_LCR_8BIT;
+ else
+ lcr_fcr = 0;
+
+ if (termios->c_cflag & CSTOPB)
+ lcr_fcr |= PNX8XXX_UART_LCR_2STOPB;
+ if (termios->c_cflag & PARENB) {
+ lcr_fcr |= PNX8XXX_UART_LCR_PAREN;
+ if (!(termios->c_cflag & PARODD))
+ lcr_fcr |= PNX8XXX_UART_LCR_PAREVN;
+ }
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ quot = uart_get_divisor(port, baud);
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+
+ sport->port.read_status_mask = ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN) |
+ ISTAT_TO_SM(PNX8XXX_UART_INT_EMPTY) |
+ ISTAT_TO_SM(PNX8XXX_UART_INT_RX);
+ if (termios->c_iflag & INPCK)
+ sport->port.read_status_mask |=
+ FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) |
+ FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR);
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ sport->port.read_status_mask |=
+ ISTAT_TO_SM(PNX8XXX_UART_INT_BREAK);
+
+ /*
+ * Characters to ignore
+ */
+ sport->port.ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ sport->port.ignore_status_mask |=
+ FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) |
+ FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR);
+ if (termios->c_iflag & IGNBRK) {
+ sport->port.ignore_status_mask |=
+ ISTAT_TO_SM(PNX8XXX_UART_INT_BREAK);
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ sport->port.ignore_status_mask |=
+ ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN);
+ }
+
+ /*
+ * ignore all characters if CREAD is not set
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ sport->port.ignore_status_mask |=
+ ISTAT_TO_SM(PNX8XXX_UART_INT_RX);
+
+ del_timer_sync(&sport->timer);
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ /*
+ * disable interrupts and drain transmitter
+ */
+ old_ien = serial_in(sport, PNX8XXX_IEN);
+ serial_out(sport, PNX8XXX_IEN, old_ien & ~(PNX8XXX_UART_INT_ALLTX |
+ PNX8XXX_UART_INT_ALLRX));
+
+ while (serial_in(sport, PNX8XXX_FIFO) & PNX8XXX_UART_FIFO_TXFIFO_STA)
+ barrier();
+
+ /* then, disable everything */
+ serial_out(sport, PNX8XXX_IEN, 0);
+
+ /* Reset the Rx and Tx FIFOs too */
+ lcr_fcr |= PNX8XXX_UART_LCR_TX_RST;
+ lcr_fcr |= PNX8XXX_UART_LCR_RX_RST;
+
+ /* set the parity, stop bits and data size */
+ serial_out(sport, PNX8XXX_LCR, lcr_fcr);
+
+ /* set the baud rate */
+ quot -= 1;
+ serial_out(sport, PNX8XXX_BAUD, quot);
+
+ serial_out(sport, PNX8XXX_ICLR, -1);
+
+ serial_out(sport, PNX8XXX_IEN, old_ien);
+
+ if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
+ pnx8xxx_enable_ms(&sport->port);
+
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+}
+
+static const char *pnx8xxx_type(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+
+ return sport->port.type == PORT_PNX8XXX ? "PNX8XXX" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'.
+ */
+static void pnx8xxx_release_port(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+
+ release_mem_region(sport->port.mapbase, UART_PORT_SIZE);
+}
+
+/*
+ * Request the memory region(s) being used by 'port'.
+ */
+static int pnx8xxx_request_port(struct uart_port *port)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ return request_mem_region(sport->port.mapbase, UART_PORT_SIZE,
+ "pnx8xxx-uart") != NULL ? 0 : -EBUSY;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void pnx8xxx_config_port(struct uart_port *port, int flags)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+
+ if (flags & UART_CONFIG_TYPE &&
+ pnx8xxx_request_port(&sport->port) == 0)
+ sport->port.type = PORT_PNX8XXX;
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ * The only change we allow are to the flags and type, and
+ * even then only between PORT_PNX8XXX and PORT_UNKNOWN
+ */
+static int
+pnx8xxx_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ int ret = 0;
+
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_PNX8XXX)
+ ret = -EINVAL;
+ if (sport->port.irq != ser->irq)
+ ret = -EINVAL;
+ if (ser->io_type != SERIAL_IO_MEM)
+ ret = -EINVAL;
+ if (sport->port.uartclk / 16 != ser->baud_base)
+ ret = -EINVAL;
+ if ((void *)sport->port.mapbase != ser->iomem_base)
+ ret = -EINVAL;
+ if (sport->port.iobase != ser->port)
+ ret = -EINVAL;
+ if (ser->hub6 != 0)
+ ret = -EINVAL;
+ return ret;
+}
+
+static struct uart_ops pnx8xxx_pops = {
+ .tx_empty = pnx8xxx_tx_empty,
+ .set_mctrl = pnx8xxx_set_mctrl,
+ .get_mctrl = pnx8xxx_get_mctrl,
+ .stop_tx = pnx8xxx_stop_tx,
+ .start_tx = pnx8xxx_start_tx,
+ .stop_rx = pnx8xxx_stop_rx,
+ .enable_ms = pnx8xxx_enable_ms,
+ .break_ctl = pnx8xxx_break_ctl,
+ .startup = pnx8xxx_startup,
+ .shutdown = pnx8xxx_shutdown,
+ .set_termios = pnx8xxx_set_termios,
+ .type = pnx8xxx_type,
+ .release_port = pnx8xxx_release_port,
+ .request_port = pnx8xxx_request_port,
+ .config_port = pnx8xxx_config_port,
+ .verify_port = pnx8xxx_verify_port,
+};
+
+
+/*
+ * Setup the PNX8XXX serial ports.
+ *
+ * Note also that we support "console=ttySx" where "x" is either 0 or 1.
+ */
+static void __init pnx8xxx_init_ports(void)
+{
+ static int first = 1;
+ int i;
+
+ if (!first)
+ return;
+ first = 0;
+
+ for (i = 0; i < NR_PORTS; i++) {
+ init_timer(&pnx8xxx_ports[i].timer);
+ pnx8xxx_ports[i].timer.function = pnx8xxx_timeout;
+ pnx8xxx_ports[i].timer.data = (unsigned long)&pnx8xxx_ports[i];
+ pnx8xxx_ports[i].port.ops = &pnx8xxx_pops;
+ }
+}
+
+#ifdef CONFIG_SERIAL_PNX8XXX_CONSOLE
+
+static void pnx8xxx_console_putchar(struct uart_port *port, int ch)
+{
+ struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
+ int status;
+
+ do {
+ /* Wait for UART_TX register to empty */
+ status = serial_in(sport, PNX8XXX_FIFO);
+ } while (status & PNX8XXX_UART_FIFO_TXFIFO);
+ serial_out(sport, PNX8XXX_FIFO, ch);
+}
+
+/*
+ * Interrupts are disabled on entering
+ */static void
+pnx8xxx_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct pnx8xxx_port *sport = &pnx8xxx_ports[co->index];
+ unsigned int old_ien, status;
+
+ /*
+ * First, save IEN and then disable interrupts
+ */
+ old_ien = serial_in(sport, PNX8XXX_IEN);
+ serial_out(sport, PNX8XXX_IEN, old_ien & ~(PNX8XXX_UART_INT_ALLTX |
+ PNX8XXX_UART_INT_ALLRX));
+
+ uart_console_write(&sport->port, s, count, pnx8xxx_console_putchar);
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore IEN
+ */
+ do {
+ /* Wait for UART_TX register to empty */
+ status = serial_in(sport, PNX8XXX_FIFO);
+ } while (status & PNX8XXX_UART_FIFO_TXFIFO);
+
+ /* Clear TX and EMPTY interrupt */
+ serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_TX |
+ PNX8XXX_UART_INT_EMPTY);
+
+ serial_out(sport, PNX8XXX_IEN, old_ien);
+}
+
+static int __init
+pnx8xxx_console_setup(struct console *co, char *options)
+{
+ struct pnx8xxx_port *sport;
+ int baud = 38400;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index == -1 || co->index >= NR_PORTS)
+ co->index = 0;
+ sport = &pnx8xxx_ports[co->index];
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(&sport->port, co, baud, parity, bits, flow);
+}
+
+extern struct uart_driver pnx8xxx_reg;
+static struct console pnx8xxx_console = {
+ .name = "ttyS",
+ .write = pnx8xxx_console_write,
+ .device = uart_console_device,
+ .setup = pnx8xxx_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &pnx8xxx_reg,
+};
+
+static int __init pnx8xxx_rs_console_init(void)
+{
+ pnx8xxx_init_ports();
+ register_console(&pnx8xxx_console);
+ return 0;
+}
+console_initcall(pnx8xxx_rs_console_init);
+
+#define PNX8XXX_CONSOLE &pnx8xxx_console
+#else
+#define PNX8XXX_CONSOLE NULL
+#endif
+
+static struct uart_driver pnx8xxx_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "ttyS",
+ .dev_name = "ttyS",
+ .major = SERIAL_PNX8XXX_MAJOR,
+ .minor = MINOR_START,
+ .nr = NR_PORTS,
+ .cons = PNX8XXX_CONSOLE,
+};
+
+static int pnx8xxx_serial_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct pnx8xxx_port *sport = platform_get_drvdata(pdev);
+
+ return uart_suspend_port(&pnx8xxx_reg, &sport->port);
+}
+
+static int pnx8xxx_serial_resume(struct platform_device *pdev)
+{
+ struct pnx8xxx_port *sport = platform_get_drvdata(pdev);
+
+ return uart_resume_port(&pnx8xxx_reg, &sport->port);
+}
+
+static int pnx8xxx_serial_probe(struct platform_device *pdev)
+{
+ struct resource *res = pdev->resource;
+ int i;
+
+ for (i = 0; i < pdev->num_resources; i++, res++) {
+ if (!(res->flags & IORESOURCE_MEM))
+ continue;
+
+ for (i = 0; i < NR_PORTS; i++) {
+ if (pnx8xxx_ports[i].port.mapbase != res->start)
+ continue;
+
+ pnx8xxx_ports[i].port.dev = &pdev->dev;
+ uart_add_one_port(&pnx8xxx_reg, &pnx8xxx_ports[i].port);
+ platform_set_drvdata(pdev, &pnx8xxx_ports[i]);
+ break;
+ }
+ }
+
+ return 0;
+}
+
+static int pnx8xxx_serial_remove(struct platform_device *pdev)
+{
+ struct pnx8xxx_port *sport = platform_get_drvdata(pdev);
+
+ platform_set_drvdata(pdev, NULL);
+
+ if (sport)
+ uart_remove_one_port(&pnx8xxx_reg, &sport->port);
+
+ return 0;
+}
+
+static struct platform_driver pnx8xxx_serial_driver = {
+ .driver = {
+ .name = "pnx8xxx-uart",
+ .owner = THIS_MODULE,
+ },
+ .probe = pnx8xxx_serial_probe,
+ .remove = pnx8xxx_serial_remove,
+ .suspend = pnx8xxx_serial_suspend,
+ .resume = pnx8xxx_serial_resume,
+};
+
+static int __init pnx8xxx_serial_init(void)
+{
+ int ret;
+
+ printk(KERN_INFO "Serial: PNX8XXX driver $Revision: 1.2 $\n");
+
+ pnx8xxx_init_ports();
+
+ ret = uart_register_driver(&pnx8xxx_reg);
+ if (ret == 0) {
+ ret = platform_driver_register(&pnx8xxx_serial_driver);
+ if (ret)
+ uart_unregister_driver(&pnx8xxx_reg);
+ }
+ return ret;
+}
+
+static void __exit pnx8xxx_serial_exit(void)
+{
+ platform_driver_unregister(&pnx8xxx_serial_driver);
+ uart_unregister_driver(&pnx8xxx_reg);
+}
+
+module_init(pnx8xxx_serial_init);
+module_exit(pnx8xxx_serial_exit);
+
+MODULE_AUTHOR("Embedded Alley Solutions, Inc.");
+MODULE_DESCRIPTION("PNX8XXX SoCs serial port driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_PNX8XXX_MAJOR);
Index: linux-2.6/drivers/serial/Makefile
===================================================================
--- linux-2.6.orig/drivers/serial/Makefile 2006-12-08 16:08:11.000000000 +0300
+++ linux-2.6/drivers/serial/Makefile 2006-12-08 18:00:00.000000000 +0300
@@ -25,6 +25,7 @@
obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
obj-$(CONFIG_SERIAL_PXA) += pxa.o
+obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2006-12-08 16:07    [W:0.051 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site