lkml.org 
[lkml]   [2006]   [Dec]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH] kbuild : Restructure Device Drivers menu for entry selectability

Rewrite a number of the Kconfig files under the drivers/ directory
so that those driver submenus can be selected or de-selected
directly from the Drivers menu using the kbuild "menuconfig" feature
without having to enter the submenu itself.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>

---

NOTE: Only those drivers submenus for which the Kconfig change was
*immediately* obvious are included here. Some of the other Kconfig
files have "issues" with dependencies so that they'll need some extra
cleanup before they can be tweaked like this as well. So this first
pass of a patch is just the beginning.

drivers/ata/Kconfig | 8 ++------
drivers/connector/Kconfig | 8 ++++----
drivers/dma/Kconfig | 10 +++++-----
drivers/edac/Kconfig | 8 ++++----
drivers/hwmon/Kconfig | 8 ++++----
drivers/i2c/Kconfig | 9 ++++-----
drivers/ide/Kconfig | 6 +-----
drivers/ieee1394/Kconfig | 7 ++++---
drivers/infiniband/Kconfig | 8 ++++----
drivers/isdn/Kconfig | 9 ++++-----
drivers/leds/Kconfig | 9 +++------
drivers/md/Kconfig | 8 ++++----
drivers/message/i2o/Kconfig | 12 +++++-------
drivers/mmc/Kconfig | 8 ++++----
drivers/mtd/Kconfig | 8 ++++----
drivers/parport/Kconfig | 8 ++++----
drivers/pnp/Kconfig | 8 ++++----
drivers/spi/Kconfig | 8 ++++----
drivers/telephony/Kconfig | 9 ++++-----
drivers/w1/Kconfig | 8 ++++----
20 files changed, 76 insertions(+), 91 deletions(-)

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 984ab28..a3bdf04 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -2,10 +2,8 @@ #
# SATA/PATA driver configuration
#

-menu "Serial ATA (prod) and Parallel ATA (experimental) drivers"
-
-config ATA
- tristate "ATA device support"
+menuconfig ATA
+ tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers"
depends on BLOCK
depends on !(M32R || M68K) || BROKEN
depends on !SUN4 || BROKEN
@@ -519,5 +517,3 @@ config PATA_IXP4XX_CF
If unsure, say N.

endif
-endmenu
-
diff --git a/drivers/connector/Kconfig b/drivers/connector/Kconfig
index e0bdc0d..9a5a061 100644
--- a/drivers/connector/Kconfig
+++ b/drivers/connector/Kconfig
@@ -1,6 +1,4 @@
-menu "Connector - unified userspace <-> kernelspace linker"
-
-config CONNECTOR
+menuconfig CONNECTOR
tristate "Connector - unified userspace <-> kernelspace linker"
depends on NET
---help---
@@ -10,6 +8,8 @@ config CONNECTOR
Connector support can also be built as a module. If so, the module
will be called cn.ko.

+if CONNECTOR
+
config PROC_EVENTS
boolean "Report process events to userspace"
depends on CONNECTOR=y
@@ -18,4 +18,4 @@ config PROC_EVENTS
Provide a connector that reports process events to userspace. Send
events such as fork, exec, id change (uid, gid, suid, etc), and exit.

-endmenu
+endif
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 30d021d..b1fb8c0 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -2,14 +2,14 @@ #
# DMA engine configuration
#

-menu "DMA Engine support"
-
-config DMA_ENGINE
- bool "Support for DMA engines"
+menuconfig DMA_ENGINE
+ bool "DMA engine support"
---help---
DMA engines offload copy operations from the CPU to dedicated
hardware, allowing the copies to happen asynchronously.

+if DMA_ENGINE
+
comment "DMA Clients"

config NET_DMA
@@ -31,4 +31,4 @@ config INTEL_IOATDMA
---help---
Enable support for the Intel(R) I/OAT DMA engine.

-endmenu
+endif
diff --git a/drivers/edac/Kconfig b/drivers/edac/Kconfig
index 4f08984..e52e9b0 100644
--- a/drivers/edac/Kconfig
+++ b/drivers/edac/Kconfig
@@ -6,10 +6,9 @@ #
# $Id: Kconfig,v 1.4.2.7 2005/07/08 22:05:38 dsp_llnl Exp $
#

-menu 'EDAC - error detection and reporting (RAS) (EXPERIMENTAL)'

-config EDAC
- tristate "EDAC core system error reporting (EXPERIMENTAL)"
+menuconfig EDAC
+ tristate 'EDAC - error detection and reporting (RAS) (EXPERIMENTAL)'
depends on X86 && EXPERIMENTAL
help
EDAC is designed to report errors in the core system.
@@ -29,6 +28,7 @@ config EDAC
There is also a mailing list for the EDAC project, which can
be found via the sourceforge page.

+if EDAC

comment "Reporting subsystems"
depends on EDAC
@@ -110,4 +110,4 @@ config EDAC_POLL

endchoice

-endmenu
+endif
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index e76d919..a4a5a33 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -2,9 +2,7 @@ #
# Hardware monitoring chip drivers configuration
#

-menu "Hardware Monitoring support"
-
-config HWMON
+menuconfig HWMON
tristate "Hardware Monitoring support"
default y
help
@@ -23,6 +21,8 @@ config HWMON
This support can also be built as a module. If so, the module
will be called hwmon.

+if HWMON
+
config HWMON_VID
tristate
default n
@@ -540,4 +540,4 @@ config HWMON_DEBUG_CHIP
a problem with I2C support and want to see more of what is going
on.

-endmenu
+endif
diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig
index 11935f6..af35094 100644
--- a/drivers/i2c/Kconfig
+++ b/drivers/i2c/Kconfig
@@ -2,9 +2,7 @@ #
# I2C subsystem configuration
#

-menu "I2C support"
-
-config I2C
+menuconfig I2C
tristate "I2C support"
---help---
I2C (pronounce: I-square-C) is a slow serial bus protocol used in
@@ -22,6 +20,8 @@ config I2C
This I2C support can also be built as a module. If so, the module
will be called i2c-core.

+if I2C
+
config I2C_CHARDEV
tristate "I2C device interface"
depends on I2C
@@ -73,5 +73,4 @@ config I2C_DEBUG_CHIP
a problem with I2C support and want to see more of what is going
on.

-endmenu
-
+endif
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 0c68d0f..a4e5569 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -6,9 +6,7 @@ #

if BLOCK

-menu "ATA/ATAPI/MFM/RLL support"
-
-config IDE
+menuconfig IDE
tristate "ATA/ATAPI/MFM/RLL support"
---help---
If you say Y here, your kernel will be able to manage low cost mass
@@ -1080,6 +1078,4 @@ config BLK_DEV_HD

endif

-endmenu
-
endif
diff --git a/drivers/ieee1394/Kconfig b/drivers/ieee1394/Kconfig
index 672b92e..411e890 100644
--- a/drivers/ieee1394/Kconfig
+++ b/drivers/ieee1394/Kconfig
@@ -1,8 +1,7 @@
# -*- shell-script -*-

-menu "IEEE 1394 (FireWire) support"

-config IEEE1394
+menuconfig IEEE1394
tristate "IEEE 1394 (FireWire) support"
depends on PCI || BROKEN
select NET
@@ -19,6 +18,8 @@ config IEEE1394
To compile this driver as a module, say M here: the
module will be called ieee1394.

+if IEEE1394
+
comment "Subsystem Options"
depends on IEEE1394

@@ -185,4 +186,4 @@ config IEEE1394_RAWIO
To compile this driver as a module, say M here: the
module will be called raw1394.

-endmenu
+endif
diff --git a/drivers/infiniband/Kconfig b/drivers/infiniband/Kconfig
index 9edface..25454e8 100644
--- a/drivers/infiniband/Kconfig
+++ b/drivers/infiniband/Kconfig
@@ -1,13 +1,13 @@
-menu "InfiniBand support"
-
config INFINIBAND
- depends on PCI || BROKEN
tristate "InfiniBand support"
+ depends on PCI || BROKEN
---help---
Core support for InfiniBand (IB). Make sure to also select
any protocols you wish to use as well as drivers for your
InfiniBand hardware.

+if INFINIBAND
+
config INFINIBAND_USER_MAD
tristate "InfiniBand userspace MAD support"
depends on INFINIBAND
@@ -45,4 +45,4 @@ source "drivers/infiniband/ulp/srp/Kconf

source "drivers/infiniband/ulp/iser/Kconfig"

-endmenu
+endif
diff --git a/drivers/isdn/Kconfig b/drivers/isdn/Kconfig
index c90afee..f7bf323 100644
--- a/drivers/isdn/Kconfig
+++ b/drivers/isdn/Kconfig
@@ -2,9 +2,7 @@ #
# ISDN device configuration
#

-menu "ISDN subsystem"
-
-config ISDN
+menuconfig ISDN
tristate "ISDN support"
depends on NET
---help---
@@ -20,6 +18,8 @@ config ISDN

Select this option if you want your kernel to support ISDN.

+if ISDN
+

menu "Old ISDN4Linux"
depends on NET && ISDN
@@ -63,5 +63,4 @@ source "drivers/isdn/capi/Kconfig"

source "drivers/isdn/hardware/Kconfig"

-endmenu
-
+endif
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 9c39b98..9e3adf1 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -1,7 +1,4 @@
-
-menu "LED devices"
-
-config NEW_LEDS
+menuconfig NEW_LEDS
bool "LED Support"
help
Say Y to enable Linux LED support. This allows control of supported
@@ -9,6 +6,7 @@ config NEW_LEDS

This is not related to standard keyboard LEDs which are controlled
via the input system.
+if NEW_LEDS

config LEDS_CLASS
tristate "LED Class Support"
@@ -109,5 +107,4 @@ config LEDS_TRIGGER_HEARTBEAT
load average.
If unsure, say Y.

-endmenu
-
+endif
diff --git a/drivers/md/Kconfig b/drivers/md/Kconfig
index c92c152..4ca02c7 100644
--- a/drivers/md/Kconfig
+++ b/drivers/md/Kconfig
@@ -4,14 +4,14 @@ #

if BLOCK

-menu "Multi-device support (RAID and LVM)"
-
-config MD
+menuconfig MD
bool "Multiple devices driver support (RAID and LVM)"
help
Support multiple physical spindles through a single logical device.
Required for RAID and logical volume management.

+if MD
+
config BLK_DEV_MD
tristate "RAID support"
depends on MD
@@ -261,6 +261,6 @@ config DM_MULTIPATH_EMC
---help---
Multipath support for EMC CX/AX series hardware.

-endmenu
+endif

endif
diff --git a/drivers/message/i2o/Kconfig b/drivers/message/i2o/Kconfig
index 6443392..6177faa 100644
--- a/drivers/message/i2o/Kconfig
+++ b/drivers/message/i2o/Kconfig
@@ -1,8 +1,5 @@
-
-menu "I2O device support"
-
-config I2O
- tristate "I2O support"
+menuconfig I2O
+ tristate "I2O device support"
depends on PCI
---help---
The Intelligent Input/Output (I2O) architecture allows hardware
@@ -24,6 +21,8 @@ config I2O

If unsure, say N.

+if I2O
+
config I2O_LCT_NOTIFY_ON_CHANGES
bool "Enable LCT notification"
depends on I2O
@@ -122,5 +121,4 @@ config I2O_PROC
To compile this support as a module, choose M here: the
module will be called i2o_proc.

-endmenu
-
+endif
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index f4f8cca..e8159dc 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -2,15 +2,15 @@ #
# MMC subsystem configuration
#

-menu "MMC/SD Card support"

-config MMC
- tristate "MMC support"
+menuconfig MMC
+ tristate "MMC/SD Card support"
help
MMC is the "multi-media card" bus protocol.

If you want MMC support, you should say Y here and also
to the specific driver for your MMC interface.
+if MMC

config MMC_DEBUG
bool "MMC debugging"
@@ -125,4 +125,4 @@ config MMC_TIFM_SD
To compile this driver as a module, choose M here: the
module will be called tifm_sd.

-endmenu
+endif
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index a304b34..3c9ae5b 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -1,8 +1,6 @@
# $Id: Kconfig,v 1.11 2005/11/07 11:14:19 gleixner Exp $

-menu "Memory Technology Devices (MTD)"
-
-config MTD
+menuconfig MTD
tristate "Memory Technology Device (MTD) support"
help
Memory Technology Devices are flash, RAM and similar chips, often
@@ -13,6 +11,8 @@ config MTD
them. It will also allow you to select individual drivers for
particular hardware and users of MTD devices. If unsure, say N.

+if MTD
+
config MTD_DEBUG
bool "Debugging"
depends on MTD
@@ -281,5 +281,5 @@ source "drivers/mtd/nand/Kconfig"

source "drivers/mtd/onenand/Kconfig"

-endmenu
+endif

diff --git a/drivers/parport/Kconfig b/drivers/parport/Kconfig
index c7fa28a..f34ae24 100644
--- a/drivers/parport/Kconfig
+++ b/drivers/parport/Kconfig
@@ -5,9 +5,7 @@ #
# Parport configuration.
#

-menu "Parallel port support"
-
-config PARPORT
+menuconfig PARPORT
tristate "Parallel port support"
---help---
If you want to use devices connected to your machine's parallel port
@@ -32,6 +30,8 @@ config PARPORT

If unsure, say Y.

+if PARPORT
+
config PARPORT_PC
tristate "PC-style hardware"
depends on PARPORT && (!SPARC64 || PCI) && !SPARC32 && !M32R && !FRV
@@ -158,5 +158,5 @@ config PARPORT_1284
transfer modes. Also say Y if you want device ID information to
appear in /proc/sys/dev/parport/*/autoprobe*. It is safe to say N.

-endmenu
+endif

diff --git a/drivers/pnp/Kconfig b/drivers/pnp/Kconfig
index c514320..ec7ab40 100644
--- a/drivers/pnp/Kconfig
+++ b/drivers/pnp/Kconfig
@@ -2,9 +2,7 @@ #
# Plug and Play configuration
#

-menu "Plug and Play support"
-
-config PNP
+menuconfig PNP
bool "Plug and Play support"
depends on ISA || ACPI
---help---
@@ -21,6 +19,8 @@ config PNP

If unsure, say Y.

+if PNP
+
config PNP_DEBUG
bool "PnP Debug Messages"
depends on PNP
@@ -37,5 +37,5 @@ source "drivers/pnp/pnpbios/Kconfig"

source "drivers/pnp/pnpacpi/Kconfig"

-endmenu
+endif

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index d895a1a..1b44244 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -5,9 +5,7 @@ # NOTE: the reason this doesn't show SP
# nobody's needed a slave side API yet. The master-role API is not
# fully appropriate there, so it'd need some thought to do well.
#
-menu "SPI support"
-
-config SPI
+menuconfig SPI
bool "SPI support"
help
The "Serial Peripheral Interface" is a low level synchronous
@@ -27,6 +25,8 @@ config SPI
(half duplex), SSP, SSI, and PSP. This driver framework should
work with most such devices and controllers.

+if SPI
+
config SPI_DEBUG
boolean "Debug support for SPI drivers"
depends on SPI && DEBUG_KERNEL
@@ -129,5 +129,5 @@ #

# (slave support would go here)

-endmenu # "SPI support"
+endif

diff --git a/drivers/telephony/Kconfig b/drivers/telephony/Kconfig
index 7625b18..d123fa1 100644
--- a/drivers/telephony/Kconfig
+++ b/drivers/telephony/Kconfig
@@ -2,9 +2,7 @@ #
# Telephony device configuration
#

-menu "Telephony Support"
-
-config PHONE
+menuconfig PHONE
tristate "Linux telephony support"
---help---
Say Y here if you have a telephony card, which for example allows
@@ -16,6 +14,8 @@ config PHONE
To compile this driver as a module, choose M here: the
module will be called phonedev.

+if PHONE
+
config PHONE_IXJ
tristate "QuickNet Internet LineJack/PhoneJack support"
depends on PHONE
@@ -43,5 +43,4 @@ config PHONE_IXJ_PCMCIA
cards manufactured by Quicknet Technologies, Inc. This changes the
card initialization code to work with the card manager daemon.

-endmenu
-
+endif
diff --git a/drivers/w1/Kconfig b/drivers/w1/Kconfig
index c287a9a..63c9c82 100644
--- a/drivers/w1/Kconfig
+++ b/drivers/w1/Kconfig
@@ -1,6 +1,4 @@
-menu "Dallas's 1-wire bus"
-
-config W1
+menuconfig W1
tristate "Dallas's 1-wire support"
---help---
Dallas' 1-wire bus is useful to connect slow 1-pin devices
@@ -11,6 +9,8 @@ config W1
This W1 support can also be built as a module. If so, the module
will be called wire.ko.

+if W1
+
config W1_CON
depends on CONNECTOR && W1
bool "Userspace communication over connector"
@@ -26,4 +26,4 @@ config W1_CON
source drivers/w1/masters/Kconfig
source drivers/w1/slaves/Kconfig

-endmenu
+endif
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2006-12-07 10:09    [W:0.035 / U:11.300 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site