lkml.org 
[lkml]   [2006]   [Dec]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: SATA300 TX4 + WD2500KS = status=0x50 { DriveReady SeekComplete }
Hello All,

I am seeing the exact same 'problem'. I have 4 WDC WD2500KS-00MJB0
drives connected to a promise SATA300 TX4. The messages have been
flooding syslog since the drives were installed. Running 2.6.18 or
2.6.19 vanilla kernels.

Best regards,

Roel Teuwen

On 10/25/06, Gregory Brauer <greg@wildbrain.com> wrote:
>
> I have a new Promise SATA300 TX4 4-port SATA controller
> to which I have attached two older WD2500JD hard drives
> and two brand new WD2500KS hard drives. The older drives
> seem to work fine, but both of the brand new hard drives
> trigger the following errors every few seconds during
> i/o:
>
>
> Oct 25 13:57:18 gleep kernel: ata3: no sense translation for status: 0x50
> Oct 25 13:57:18 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Oct 25 13:57:18 gleep kernel: ata3: status=0x50 { DriveReady SeekComplete }
> Oct 25 13:57:26 gleep kernel: ata1: no sense translation for status: 0x50
> Oct 25 13:57:26 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Oct 25 13:57:26 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete }
> Oct 25 13:57:27 gleep kernel: ata1: no sense translation for status: 0x50
> Oct 25 13:57:27 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Oct 25 13:57:27 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete }
> Oct 25 13:57:31 gleep kernel: ata1: no sense translation for status: 0x50
> Oct 25 13:57:31 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Oct 25 13:57:31 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete }
> Oct 25 13:57:47 gleep kernel: ata3: no sense translation for status: 0x50
> Oct 25 13:57:47 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI
> SK/ASC/ASCQ 0xb/00/00
> Oct 25 13:57:47 gleep kernel: ata3: status=0x50 { DriveReady SeekComplete }
>
>
> The machine stays running normally, and any processes doing data
> I/O do not pause noticeably, but these errors are very annoying.
> Is there anything I can do to help troubleshoot this?
>
> (Note that I am aware of the drive id mapping issue with my Promise
> controller, and I am *positive* that it is the two new drives that
> are the one's that the error messages refer to.)
>
> Thanks.
>
> Greg
>
>
> System Info
> -----------
>
> Fedora Core 5
> 2.6.18-1.2200.fc5smp
>
>
> Device Model: WDC WD2500KS-00MJB0
> Firmware Version: 02.01C03
>
>
> # lspci
> 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
> (rev 03)
> 00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
> (rev 03)
> 00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
> 00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
> 00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
> 00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02)
> 00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20718 (SATA 300
> TX4) (rev 02)
> 00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
> 00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07)
> 00:0f.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet
> Controller (rev 05)
> 00:11.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 00:11.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 00:11.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
> 00:11.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
> 00:11.4 FireWire (IEEE 1394): ALi Corporation M5253 P1394 OHCI 1.1 Controller
> 00:13.0 Mass storage controller: Triones Technologies, Inc.
> HPT366/368/370/370A/372/372N (rev 01)
> 00:13.1 Mass storage controller: Triones Technologies, Inc.
> HPT366/368/370/370A/372/372N (rev 01)
> 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
>
>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2006-12-19 12:29    [W:3.214 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site