lkml.org 
[lkml]   [2006]   [Dec]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 3/10] cxgb3 - HW access routines - part 1
From: Divy Le Ray <divy@chelsio.com>
[PATCH 3/10] cxgb3 - HW access routines - part 1


This patch implements the HW access routines for the
Chelsio T3 network adapter's driver.
This patch is split. This is the first part.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
---
drivers/net/cxgb3/t3_hw.c | 3352 +++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 3352 insertions(+), 0 deletions(-)

diff --git a/drivers/net/cxgb3/t3_hw.c b/drivers/net/cxgb3/t3_hw.c
new file mode 100755
index 0000000..3a1802d
--- /dev/null
+++ b/drivers/net/cxgb3/t3_hw.c
@@ -0,0 +1,3352 @@
+/*
+ * This file is part of the Chelsio T3 Ethernet driver.
+ *
+ * Copyright (C) 2003-2006 Chelsio Communications. All rights reserved.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the LICENSE file included in this
+ * release for licensing terms and conditions.
+ */
+
+#include "common.h"
+#include "regs.h"
+#include "sge_defs.h"
+#include "firmware_exports.h"
+
+ /**
+  * t3_wait_op_done_val - wait until an operation is completed
+ * @adapter: the adapter performing the operation
+ * @reg: the register to check for completion
+ * @mask: a single-bit field within @reg that indicates completion
+ * @polarity: the value of the field when the operation is completed
+ * @attempts: number of check iterations
+ * @delay: delay in usecs between iterations
+ * @valp: where to store the value of the register at completion time
+ *
+ * Wait until an operation is completed by checking a bit in a register
+ * up to @attempts times. If @valp is not NULL the value of the register
+ * at the time it indicated completion is stored there. Returns 0 if the
+ * operation completes and -EAGAIN otherwise.
+ */
+
+int t3_wait_op_done_val(struct adapter *adapter, int reg, u32 mask,
+ int polarity, int attempts, int delay, u32 *valp)
+{
+ while (1) {
+ u32 val = t3_read_reg(adapter, reg);
+
+ if (!!(val & mask) == polarity) {
+ if (valp)
+ *valp = val;
+ return 0;
+ }
+ if (--attempts == 0)
+ return -EAGAIN;
+ if (delay)
+ udelay(delay);
+ }
+}
+
+/**
+ * t3_write_regs - write a bunch of registers
+ * @adapter: the adapter to program
+ * @p: an array of register address/register value pairs
+ * @n: the number of address/value pairs
+ * @offset: register address offset
+ *
+ * Takes an array of register address/register value pairs and writes each
+ * value to the corresponding register. Register addresses are adjusted
+ * by the supplied offset.
+ */
+void t3_write_regs(struct adapter *adapter, const struct addr_val_pair *p,
+ int n, unsigned int offset)
+{
+ while (n--) {
+ t3_write_reg(adapter, p->reg_addr + offset, p->val);
+ p++;
+ }
+}
+
+/**
+ * t3_set_reg_field - set a register field to a value
+ * @adapter: the adapter to program
+ * @addr: the register address
+ * @mask: specifies the portion of the register to modify
+ * @val: the new value for the register field
+ *
+ * Sets a register field specified by the supplied mask to the
+ * given value.
+ */
+void t3_set_reg_field(struct adapter *adapter, unsigned int addr, u32 mask,
+ u32 val)
+{
+ u32 v = t3_read_reg(adapter, addr) & ~mask;
+
+ t3_write_reg(adapter, addr, v | val);
+ (void)t3_read_reg(adapter, addr); /* flush */
+}
+
+/**
+ * t3_read_indirect - read indirectly addressed registers
+ * @adap: the adapter
+ * @addr_reg: register holding the indirect address
+ * @data_reg: register holding the value of the indirect register
+ * @vals: where the read register values are stored
+ * @start_idx: index of first indirect register to read
+ * @nregs: how many indirect registers to read
+ *
+ * Reads registers that are accessed indirectly through an address/data
+ * register pair.
+ */
+void t3_read_indirect(struct adapter *adap, unsigned int addr_reg,
+ unsigned int data_reg, u32 *vals, unsigned int nregs,
+ unsigned int start_idx)
+{
+ while (nregs--) {
+ t3_write_reg(adap, addr_reg, start_idx);
+ *vals++ = t3_read_reg(adap, data_reg);
+ start_idx++;
+ }
+}
+
+/**
+ * t3_mc7_bd_read - read from MC7 through backdoor accesses
+ * @mc7: identifies MC7 to read from
+ * @start: index of first 64-bit word to read
+ * @n: number of 64-bit words to read
+ * @buf: where to store the read result
+ *
+ * Read n 64-bit words from MC7 starting at word start, using backdoor
+ * accesses.
+ */
+int t3_mc7_bd_read(struct mc7 *mc7, unsigned int start, unsigned int n,
+ u64 *buf)
+{
+ static const int shift[] = { 0, 0, 16, 24 };
+ static const int step[] = { 0, 32, 16, 8 };
+
+ unsigned int size64 = mc7->size / 8; /* # of 64-bit words */
+ struct adapter *adap = mc7->adapter;
+
+ if (start >= size64 || start + n > size64)
+ return -EINVAL;
+
+ start *= (8 << mc7->width);
+ while (n--) {
+ int i;
+ u64 val64 = 0;
+
+ for (i = (1 << mc7->width) - 1; i >= 0; --i) {
+ int attempts = 10;
+ u32 val;
+
+ t3_write_reg(adap, mc7->offset + A_MC7_BD_ADDR, start);
+ t3_write_reg(adap, mc7->offset + A_MC7_BD_OP, 0);
+ val = t3_read_reg(adap, mc7->offset + A_MC7_BD_OP);
+ while ((val & F_BUSY) && attempts--)
+ val = t3_read_reg(adap,
+ mc7->offset + A_MC7_BD_OP);
+ if (val & F_BUSY)
+ return -EIO;
+
+ val = t3_read_reg(adap, mc7->offset + A_MC7_BD_DATA1);
+ if (mc7->width == 0) {
+ val64 = t3_read_reg(adap,
+ mc7->offset +
+ A_MC7_BD_DATA0);
+ val64 |= (u64) val << 32;
+ } else {
+ if (mc7->width > 1)
+ val >>= shift[mc7->width];
+ val64 |= (u64) val << (step[mc7->width] * i);
+ }
+ start += 8;
+ }
+ *buf++ = val64;
+ }
+ return 0;
+}
+
+/*
+ * Initialize MI1.
+ */
+static void mi1_init(struct adapter *adap, const struct adapter_info *ai)
+{
+ u32 clkdiv = adap->params.vpd.cclk / (2 * adap->params.vpd.mdc) - 1;
+ u32 val = F_PREEN | V_MDIINV(ai->mdiinv) | V_MDIEN(ai->mdien) |
+ V_CLKDIV(clkdiv);
+
+ if (!(ai->caps & SUPPORTED_10000baseT_Full))
+ val |= V_ST(1);
+ t3_write_reg(adap, A_MI1_CFG, val);
+}
+
+#define MDIO_ATTEMPTS 10
+
+/*
+ * MI1 read/write operations for direct-addressed PHYs.
+ */
+static int mi1_read(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr, unsigned int *valp)
+{
+ int ret;
+ u32 addr = V_REGADDR(reg_addr) | V_PHYADDR(phy_addr);
+
+ if (mmd_addr)
+ return -EINVAL;
+
+ mutex_lock(&adapter->mdio_lock);
+ t3_write_reg(adapter, A_MI1_ADDR, addr);
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(2));
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ if (!ret)
+ *valp = t3_read_reg(adapter, A_MI1_DATA);
+ mutex_unlock(&adapter->mdio_lock);
+ return ret;
+}
+
+static int mi1_write(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr, unsigned int val)
+{
+ int ret;
+ u32 addr = V_REGADDR(reg_addr) | V_PHYADDR(phy_addr);
+
+ if (mmd_addr)
+ return -EINVAL;
+
+ mutex_lock(&adapter->mdio_lock);
+ t3_write_reg(adapter, A_MI1_ADDR, addr);
+ t3_write_reg(adapter, A_MI1_DATA, val);
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(1));
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ mutex_unlock(&adapter->mdio_lock);
+ return ret;
+}
+
+static const struct mdio_ops mi1_mdio_ops = {
+ mi1_read,
+ mi1_write
+};
+
+/*
+ * MI1 read/write operations for indirect-addressed PHYs.
+ */
+static int mi1_ext_read(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr, unsigned int *valp)
+{
+ int ret;
+ u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
+
+ mutex_lock(&adapter->mdio_lock);
+ t3_write_reg(adapter, A_MI1_ADDR, addr);
+ t3_write_reg(adapter, A_MI1_DATA, reg_addr);
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ if (!ret) {
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(3));
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
+ MDIO_ATTEMPTS, 20);
+ if (!ret)
+ *valp = t3_read_reg(adapter, A_MI1_DATA);
+ }
+ mutex_unlock(&adapter->mdio_lock);
+ return ret;
+}
+
+static int mi1_ext_write(struct adapter *adapter, int phy_addr, int mmd_addr,
+ int reg_addr, unsigned int val)
+{
+ int ret;
+ u32 addr = V_REGADDR(mmd_addr) | V_PHYADDR(phy_addr);
+
+ mutex_lock(&adapter->mdio_lock);
+ t3_write_reg(adapter, A_MI1_ADDR, addr);
+ t3_write_reg(adapter, A_MI1_DATA, reg_addr);
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(0));
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0, MDIO_ATTEMPTS, 20);
+ if (!ret) {
+ t3_write_reg(adapter, A_MI1_DATA, val);
+ t3_write_reg(adapter, A_MI1_OP, V_MDI_OP(1));
+ ret = t3_wait_op_done(adapter, A_MI1_OP, F_BUSY, 0,
+ MDIO_ATTEMPTS, 20);
+ }
+ mutex_unlock(&adapter->mdio_lock);
+ return ret;
+}
+
+static const struct mdio_ops mi1_mdio_ext_ops = {
+ mi1_ext_read,
+ mi1_ext_write
+};
+
+/**
+ * t3_mdio_change_bits - modify the value of a PHY register
+ * @phy: the PHY to operate on
+ * @mmd: the device address
+ * @reg: the register address
+ * @clear: what part of the register value to mask off
+ * @set: what part of the register value to set
+ *
+ * Changes the value of a PHY register by applying a mask to its current
+ * value and ORing the result with a new value.
+ */
+int t3_mdio_change_bits(struct cphy *phy, int mmd, int reg, unsigned int clear,
+ unsigned int set)
+{
+ int ret;
+ unsigned int val;
+
+ ret = mdio_read(phy, mmd, reg, &val);
+ if (!ret) {
+ val &= ~clear;
+ ret = mdio_write(phy, mmd, reg, val | set);
+ }
+ return ret;
+}
+
+/**
+ * t3_phy_reset - reset a PHY block
+ * @phy: the PHY to operate on
+ * @mmd: the device address of the PHY block to reset
+ * @wait: how long to wait for the reset to complete in 1ms increments
+ *
+ * Resets a PHY block and optionally waits for the reset to complete.
+ * @mmd should be 0 for 10/100/1000 PHYs and the device address to reset
+ * for 10G PHYs.
+ */
+int t3_phy_reset(struct cphy *phy, int mmd, int wait)
+{
+ int err;
+ unsigned int ctl;
+
+ err = t3_mdio_change_bits(phy, mmd, MII_BMCR, BMCR_PDOWN, BMCR_RESET);
+ if (err || !wait)
+ return err;
+
+ do {
+ err = mdio_read(phy, mmd, MII_BMCR, &ctl);
+ if (err)
+ return err;
+ ctl &= BMCR_RESET;
+ if (ctl)
+ msleep(1);
+ } while (ctl && --wait);
+
+ return ctl ? -1 : 0;
+}
+
+/**
+ * t3_phy_advertise - set the PHY advertisement registers for autoneg
+ * @phy: the PHY to operate on
+ * @advert: bitmap of capabilities the PHY should advertise
+ *
+ * Sets a 10/100/1000 PHY's advertisement registers to advertise the
+ * requested capabilities.
+ */
+int t3_phy_advertise(struct cphy *phy, unsigned int advert)
+{
+ int err;
+ unsigned int val = 0;
+
+ err = mdio_read(phy, 0, MII_CTRL1000, &val);
+ if (err)
+ return err;
+
+ val &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL);
+ if (advert & ADVERTISED_1000baseT_Half)
+ val |= ADVERTISE_1000HALF;
+ if (advert & ADVERTISED_1000baseT_Full)
+ val |= ADVERTISE_1000FULL;
+
+ err = mdio_write(phy, 0, MII_CTRL1000, val);
+ if (err)
+ return err;
+
+ val = 1;
+ if (advert & ADVERTISED_10baseT_Half)
+ val |= ADVERTISE_10HALF;
+ if (advert & ADVERTISED_10baseT_Full)
+ val |= ADVERTISE_10FULL;
+ if (advert & ADVERTISED_100baseT_Half)
+ val |= ADVERTISE_100HALF;
+ if (advert & ADVERTISED_100baseT_Full)
+ val |= ADVERTISE_100FULL;
+ if (advert & ADVERTISED_Pause)
+ val |= ADVERTISE_PAUSE_CAP;
+ if (advert & ADVERTISED_Asym_Pause)
+ val |= ADVERTISE_PAUSE_ASYM;
+ return mdio_write(phy, 0, MII_ADVERTISE, val);
+}
+
+/**
+ * t3_set_phy_speed_duplex - force PHY speed and duplex
+ * @phy: the PHY to operate on
+ * @speed: requested PHY speed
+ * @duplex: requested PHY duplex
+ *
+ * Force a 10/100/1000 PHY's speed and duplex. This also disables
+ * auto-negotiation except for GigE, where auto-negotiation is mandatory.
+ */
+int t3_set_phy_speed_duplex(struct cphy *phy, int speed, int duplex)
+{
+ int err;
+ unsigned int ctl;
+
+ err = mdio_read(phy, 0, MII_BMCR, &ctl);
+ if (err)
+ return err;
+
+ if (speed >= 0) {
+ ctl &= ~(BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE);
+ if (speed == SPEED_100)
+ ctl |= BMCR_SPEED100;
+ else if (speed == SPEED_1000)
+ ctl |= BMCR_SPEED1000;
+ }
+ if (duplex >= 0) {
+ ctl &= ~(BMCR_FULLDPLX | BMCR_ANENABLE);
+ if (duplex == DUPLEX_FULL)
+ ctl |= BMCR_FULLDPLX;
+ }
+ if (ctl & BMCR_SPEED1000) /* auto-negotiation required for GigE */
+ ctl |= BMCR_ANENABLE;
+ return mdio_write(phy, 0, MII_BMCR, ctl);
+}
+
+static const struct adapter_info t3_adap_info[] = {
+ {2, 0, 0, 0,
+ F_GPIO2_OEN | F_GPIO4_OEN |
+ F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
+ SUPPORTED_OFFLOAD,
+ &mi1_mdio_ops, "Chelsio PE9000"},
+ {2, 0, 0, 0,
+ F_GPIO2_OEN | F_GPIO4_OEN |
+ F_GPIO2_OUT_VAL | F_GPIO4_OUT_VAL, F_GPIO3 | F_GPIO5,
+ SUPPORTED_OFFLOAD,
+ &mi1_mdio_ops, "Chelsio T302"},
+ {1, 0, 0, 0,
+ F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN | F_GPIO10_OEN |
+ F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0,
+ SUPPORTED_10000baseT_Full | SUPPORTED_AUI | SUPPORTED_OFFLOAD,
+ &mi1_mdio_ext_ops, "Chelsio T310"},
+ {2, 0, 0, 0,
+ F_GPIO1_OEN | F_GPIO2_OEN | F_GPIO4_OEN | F_GPIO5_OEN | F_GPIO6_OEN |
+ F_GPIO7_OEN | F_GPIO10_OEN | F_GPIO11_OEN | F_GPIO1_OUT_VAL |
+ F_GPIO5_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0,
+ SUPPORTED_10000baseT_Full | SUPPORTED_AUI | SUPPORTED_OFFLOAD,
+ &mi1_mdio_ext_ops, "Chelsio T320"},
+};
+
+/*
+ * Return the adapter_info structure with a given index. Out-of-range indices
+ * return NULL.
+ */
+const struct adapter_info *t3_get_adapter_info(unsigned int id)
+{
+ return id < ARRAY_SIZE(t3_adap_info) ? &t3_adap_info[id] : NULL;
+}
+
+#define CAPS_1G (SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full | \
+ SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg | SUPPORTED_MII)
+#define CAPS_10G (SUPPORTED_10000baseT_Full | SUPPORTED_AUI)
+
+static const struct port_type_info port_types[] = {
+ {NULL},
+ {t3_ael1002_phy_prep, CAPS_10G | SUPPORTED_FIBRE,
+ "10GBASE-XR"},
+ {t3_vsc8211_phy_prep, CAPS_1G | SUPPORTED_TP | SUPPORTED_IRQ,
+ "10/100/1000BASE-T"},
+ {NULL, CAPS_1G | SUPPORTED_TP | SUPPORTED_IRQ,
+ "10/100/1000BASE-T"},
+ {t3_xaui_direct_phy_prep, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
+ {NULL, CAPS_10G, "10GBASE-KX4"},
+ {t3_qt2045_phy_prep, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
+ {t3_ael1006_phy_prep, CAPS_10G | SUPPORTED_FIBRE,
+ "10GBASE-SR"},
+ {NULL, CAPS_10G | SUPPORTED_TP, "10GBASE-CX4"},
+};
+
+#undef CAPS_1G
+#undef CAPS_10G
+
+#define VPD_ENTRY(name, len) \
+ u8 name##_kword[2]; u8 name##_len; u8 name##_data[len]
+
+/*
+ * Partial EEPROM Vital Product Data structure. Includes only the ID and
+ * VPD-R sections.
+ */
+struct t3_vpd {
+ u8 id_tag;
+ u8 id_len[2];
+ u8 id_data[16];
+ u8 vpdr_tag;
+ u8 vpdr_len[2];
+ VPD_ENTRY(pn, 16); /* part number */
+ VPD_ENTRY(ec, 16); /* EC level */
+ VPD_ENTRY(sn, 16); /* serial number */
+ VPD_ENTRY(na, 12); /* MAC address base */
+ VPD_ENTRY(cclk, 6); /* core clock */
+ VPD_ENTRY(mclk, 6); /* mem clock */
+ VPD_ENTRY(uclk, 6); /* uP clk */
+ VPD_ENTRY(mdc, 6); /* MDIO clk */
+ VPD_ENTRY(mt, 2); /* mem timing */
+ VPD_ENTRY(xaui0cfg, 6); /* XAUI0 config */
+ VPD_ENTRY(xaui1cfg, 6); /* XAUI1 config */
+ VPD_ENTRY(port0, 2); /* PHY0 complex */
+ VPD_ENTRY(port1, 2); /* PHY1 complex */
+ VPD_ENTRY(port2, 2); /* PHY2 complex */
+ VPD_ENTRY(port3, 2); /* PHY3 complex */
+ VPD_ENTRY(rv, 1); /* csum */
+ u32 pad; /* for multiple-of-4 sizing and alignment */
+};
+
+#define EEPROM_MAX_POLL 4
+#define EEPROM_STAT_ADDR 0x4000
+#define VPD_BASE 0xc00
+
+/**
+ * t3_seeprom_read - read a VPD EEPROM location
+ * @adapter: adapter to read
+ * @addr: EEPROM address
+ * @data: where to store the read data
+ *
+ * Read a 32-bit word from a location in VPD EEPROM using the card's PCI
+ * VPD ROM capability. A zero is written to the flag bit when the
+ * addres is written to the control register. The hardware device will
+ * set the flag to 1 when 4 bytes have been read into the data register.
+ */
+int t3_seeprom_read(struct adapter *adapter, u32 addr, u32 *data)
+{
+ u16 val;
+ int attempts = EEPROM_MAX_POLL;
+ unsigned int base = adapter->params.pci.vpd_cap_addr;
+
+ if ((addr >= EEPROMSIZE && addr != EEPROM_STAT_ADDR) || (addr & 3))
+ return -EINVAL;
+
+ pci_write_config_word(adapter->pdev, base + PCI_VPD_ADDR, (u16) addr);
+ do {
+ udelay(10);
+ pci_read_config_word(adapter->pdev, base + PCI_VPD_ADDR, &val);
+ } while (!(val & PCI_VPD_ADDR_F) && --attempts);
+
+ if (!(val & PCI_VPD_ADDR_F)) {
+ CH_ERR(adapter, "reading EEPROM address 0x%x failed\n", addr);
+ return -EIO;
+ }
+ pci_read_config_dword(adapter->pdev, base + PCI_VPD_DATA, data);
+ *data = le32_to_cpu(*data);
+ return 0;
+}
+
+/**
+ * t3_seeprom_write - write a VPD EEPROM location
+ * @adapter: adapter to write
+ * @addr: EEPROM address
+ * @data: value to write
+ *
+ * Write a 32-bit word to a location in VPD EEPROM using the card's PCI
+ * VPD ROM capability.
+ */
+int t3_seeprom_write(struct adapter *adapter, u32 addr, u32 data)
+{
+ u16 val;
+ int attempts = EEPROM_MAX_POLL;
+ unsigned int base = adapter->params.pci.vpd_cap_addr;
+
+ if ((addr >= EEPROMSIZE && addr != EEPROM_STAT_ADDR) || (addr & 3))
+ return -EINVAL;
+
+ pci_write_config_dword(adapter->pdev, base + PCI_VPD_DATA,
+ cpu_to_le32(data));
+ pci_write_config_word(adapter->pdev,base + PCI_VPD_ADDR,
+ (u16)addr | PCI_VPD_ADDR_F);
+ do {
+ msleep(1);
+ pci_read_config_word(adapter->pdev, base + PCI_VPD_ADDR, &val);
+ } while ((val & PCI_VPD_ADDR_F) && --attempts);
+
+ if (val & PCI_VPD_ADDR_F) {
+ CH_ERR(adapter, "write to EEPROM address 0x%x failed\n", addr);
+ return -EIO;
+ }
+ return 0;
+}
+
+/**
+ * t3_seeprom_wp - enable/disable EEPROM write protection
+ * @adapter: the adapter
+ * @enable: 1 to enable write protection, 0 to disable it
+ *
+ * Enables or disables write protection on the serial EEPROM.
+ */
+int t3_seeprom_wp(struct adapter *adapter, int enable)
+{
+ return t3_seeprom_write(adapter, EEPROM_STAT_ADDR, enable ? 0xc : 0);
+}
+
+/*
+ * Convert a character holding a hex digit to a number.
+ */
+static unsigned int hex2int(unsigned char c)
+{
+ return isdigit(c) ? c - '0' : toupper(c) - 'A' + 10;
+}
+
+/**
+ * get_vpd_params - read VPD parameters from VPD EEPROM
+ * @adapter: adapter to read
+ * @p: where to store the parameters
+ *
+ * Reads card parameters stored in VPD EEPROM.
+ */
+static int get_vpd_params(struct adapter *adapter, struct vpd_params *p)
+{
+ int i, addr, ret;
+ struct t3_vpd vpd;
+
+ /*
+ * Card information is normally at VPD_BASE but some early cards had
+ * it at 0.
+ */
+ ret = t3_seeprom_read(adapter, VPD_BASE, (u32 *) & vpd);
+ if (ret)
+ return ret;
+ addr = vpd.id_tag == 0x82 ? VPD_BASE : 0;
+
+ for (i = 0; i < sizeof(vpd); i += 4) {
+ ret = t3_seeprom_read(adapter, addr + i,
+ (u32 *)((u8 *)&vpd + i));
+ if (ret)
+ return ret;
+ }
+
+ p->cclk = simple_strtoul(vpd.cclk_data, NULL, 10);
+ p->mclk = simple_strtoul(vpd.mclk_data, NULL, 10);
+ p->uclk = simple_strtoul(vpd.uclk_data, NULL, 10);
+ p->mdc = simple_strtoul(vpd.mdc_data, NULL, 10);
+ p->mem_timing = simple_strtoul(vpd.mt_data, NULL, 10);
+
+ /* Old eeproms didn't have port information */
+ if (adapter->params.rev == 0 && !vpd.port0_data[0]) {
+ p->port_type[0] = uses_xaui(adapter) ? 1 : 2;
+ p->port_type[1] = uses_xaui(adapter) ? 6 : 2;
+ } else {
+ p->port_type[0] = (u8) hex2int(vpd.port0_data[0]);
+ p->port_type[1] = (u8) hex2int(vpd.port1_data[0]);
+ p->xauicfg[0] = simple_strtoul(vpd.xaui0cfg_data, NULL, 16);
+ p->xauicfg[1] = simple_strtoul(vpd.xaui1cfg_data, NULL, 16);
+ }
+
+ for (i = 0; i < 6; i++)
+ p->eth_base[i] = hex2int(vpd.na_data[2 * i]) * 16 +
+ hex2int(vpd.na_data[2 * i + 1]);
+ return 0;
+}
+
+/* serial flash and firmware constants */
+enum {
+ SF_ATTEMPTS = 5, /* max retries for SF1 operations */
+ SF_SEC_SIZE = 64 * 1024, /* serial flash sector size */
+ SF_SIZE = SF_SEC_SIZE * 8, /* serial flash size */
+
+ /* flash command opcodes */
+ SF_PROG_PAGE = 2, /* program page */
+ SF_WR_DISABLE = 4, /* disable writes */
+ SF_RD_STATUS = 5, /* read status register */
+ SF_WR_ENABLE = 6, /* enable writes */
+ SF_RD_DATA_FAST = 0xb, /* read flash */
+ SF_ERASE_SECTOR = 0xd8, /* erase sector */
+
+ FW_FLASH_BOOT_ADDR = 0x70000, /* start address of FW in flash */
+ FW_VERS_ADDR = 0x77ffc /* flash address holding FW version */
+};
+
+/**
+ * sf1_read - read data from the serial flash
+ * @adapter: the adapter
+ * @byte_cnt: number of bytes to read
+ * @cont: whether another operation will be chained
+ * @valp: where to store the read data
+ *
+ * Reads up to 4 bytes of data from the serial flash. The location of
+ * the read needs to be specified prior to calling this by issuing the
+ * appropriate commands to the serial flash.
+ */
+static int sf1_read(struct adapter *adapter, unsigned int byte_cnt, int cont,
+ u32 *valp)
+{
+ int ret;
+
+ if (!byte_cnt || byte_cnt > 4)
+ return -EINVAL;
+ if (t3_read_reg(adapter, A_SF_OP) & F_BUSY)
+ return -EBUSY;
+ t3_write_reg(adapter, A_SF_OP, V_CONT(cont) | V_BYTECNT(byte_cnt - 1));
+ ret = t3_wait_op_done(adapter, A_SF_OP, F_BUSY, 0, SF_ATTEMPTS, 10);
+ if (!ret)
+ *valp = t3_read_reg(adapter, A_SF_DATA);
+ return ret;
+}
+
+/**
+ * sf1_write - write data to the serial flash
+ * @adapter: the adapter
+ * @byte_cnt: number of bytes to write
+ * @cont: whether another operation will be chained
+ * @val: value to write
+ *
+ * Writes up to 4 bytes of data to the serial flash. The location of
+ * the write needs to be specified prior to calling this by issuing the
+ * appropriate commands to the serial flash.
+ */
+static int sf1_write(struct adapter *adapter, unsigned int byte_cnt, int cont,
+ u32 val)
+{
+ if (!byte_cnt || byte_cnt > 4)
+ return -EINVAL;
+ if (t3_read_reg(adapter, A_SF_OP) & F_BUSY)
+ return -EBUSY;
+ t3_write_reg(adapter, A_SF_DATA, val);
+ t3_write_reg(adapter, A_SF_OP,
+ V_CONT(cont) | V_BYTECNT(byte_cnt - 1) | V_OP(1));
+ return t3_wait_op_done(adapter, A_SF_OP, F_BUSY, 0, SF_ATTEMPTS, 10);
+}
+
+/**
+ * flash_wait_op - wait for a flash operation to complete
+ * @adapter: the adapter
+ * @attempts: max number of polls of the status register
+ * @delay: delay between polls in ms
+ *
+ * Wait for a flash operation to complete by polling the status register.
+ */
+static int flash_wait_op(struct adapter *adapter, int attempts, int delay)
+{
+ int ret;
+ u32 status;
+
+ while (1) {
+ if ((ret = sf1_write(adapter, 1, 1, SF_RD_STATUS)) != 0 ||
+ (ret = sf1_read(adapter, 1, 0, &status)) != 0)
+ return ret;
+ if (!(status & 1))
+ return 0;
+ if (--attempts == 0)
+ return -EAGAIN;
+ if (delay)
+ msleep(delay);
+ }
+}
+
+/**
+ * t3_read_flash - read words from serial flash
+ * @adapter: the adapter
+ * @addr: the start address for the read
+ * @nwords: how many 32-bit words to read
+ * @data: where to store the read data
+ * @byte_oriented: whether to store data as bytes or as words
+ *
+ * Read the specified number of 32-bit words from the serial flash.
+ * If @byte_oriented is set the read data is stored as a byte array
+ * (i.e., big-endian), otherwise as 32-bit words in the platform's
+ * natural endianess.
+ */
+int t3_read_flash(struct adapter *adapter, unsigned int addr,
+ unsigned int nwords, u32 *data, int byte_oriented)
+{
+ int ret;
+
+ if (addr + nwords * sizeof(u32) > SF_SIZE || (addr & 3))
+ return -EINVAL;
+
+ addr = swab32(addr) | SF_RD_DATA_FAST;
+
+ if ((ret = sf1_write(adapter, 4, 1, addr)) != 0 ||
+ (ret = sf1_read(adapter, 1, 1, data)) != 0)
+ return ret;
+
+ for (; nwords; nwords--, data++) {
+ ret = sf1_read(adapter, 4, nwords > 1, data);
+ if (ret)
+ return ret;
+ if (byte_oriented)
+ *data = htonl(*data);
+ }
+ return 0;
+}
+
+/**
+ * t3_write_flash - write up to a page of data to the serial flash
+ * @adapter: the adapter
+ * @addr: the start address to write
+ * @n: length of data to write
+ * @data: the data to write
+ *
+ * Writes up to a page of data (256 bytes) to the serial flash starting
+ * at the given address.
+ */
+static int t3_write_flash(struct adapter *adapter, unsigned int addr,
+ unsigned int n, const u8 * data)
+{
+ int ret;
+ u32 buf[64];
+ unsigned int i, c, left, val, offset = addr & 0xff;
+
+ if (addr + n > SF_SIZE || offset + n > 256)
+ return -EINVAL;
+
+ val = swab32(addr) | SF_PROG_PAGE;
+
+ if ((ret = sf1_write(adapter, 1, 0, SF_WR_ENABLE)) != 0 ||
+ (ret = sf1_write(adapter, 4, 1, val)) != 0)
+ return ret;
+
+ for (left = n; left; left -= c) {
+ c = min(left, 4U);
+ for (val = 0, i = 0; i < c; ++i)
+ val = (val << 8) + *data++;
+
+ ret = sf1_write(adapter, c, c != left, val);
+ if (ret)
+ return ret;
+ }
+ if ((ret = flash_wait_op(adapter, 5, 1)) != 0)
+ return ret;
+
+ /* Read the page to verify the write succeeded */
+ ret = t3_read_flash(adapter, addr & ~0xff, ARRAY_SIZE(buf), buf, 1);
+ if (ret)
+ return ret;
+
+ if (memcmp(data - n, (u8 *) buf + offset, n))
+ return -EIO;
+ return 0;
+}
+
+/**
+ * t3_get_fw_version - read the firmware version
+ * @adapter: the adapter
+ * @vers: where to place the version
+ *
+ * Reads the FW version from flash.
+ */
+int t3_get_fw_version(struct adapter *adapter, u32 *vers)
+{
+ return t3_read_flash(adapter, FW_VERS_ADDR, 1, vers, 0);
+}
+
+/**
+ * t3_check_fw_version - check if the FW is compatible with this driver
+ * @adapter: the adapter
+ *
+ * Checks if an adapter's FW is compatible with the driver. Returns 0
+ * if the versions are compatible, a negative error otherwise.
+ */
+int t3_check_fw_version(struct adapter *adapter)
+{
+ int ret;
+ u32 vers;
+
+ ret = t3_get_fw_version(adapter, &vers);
+ if (ret)
+ return ret;
+
+ /* Minor 0xfff means the FW is an internal development-only version. */
+ if ((vers & 0xfff) == 0xfff)
+ return 0;
+
+ if (vers == 0x1002009)
+ return 0;
+
+ CH_ERR(adapter, "found wrong FW version, driver needs version 2.9\n");
+ return -EINVAL;
+}
+
+/**
+ * t3_flash_erase_sectors - erase a range of flash sectors
+ * @adapter: the adapter
+ * @start: the first sector to erase
+ * @end: the last sector to erase
+ *
+ * Erases the sectors in the given range.
+ */
+static int t3_flash_erase_sectors(struct adapter *adapter, int start, int end)
+{
+ while (start <= end) {
+ int ret;
+
+ if ((ret = sf1_write(adapter, 1, 0, SF_WR_ENABLE)) != 0 ||
+ (ret = sf1_write(adapter, 4, 0,
+ SF_ERASE_SECTOR | (start << 8))) != 0 ||
+ (ret = flash_wait_op(adapter, 5, 500)) != 0)
+ return ret;
+ start++;
+ }
+ return 0;
+}
+
+/*
+ * t3_load_fw - download firmware
+ * @adapter: the adapter
+ * @fw_data: the firrware image to write
+ * @size: image size
+ *
+ * Write the supplied firmware image to the card's serial flash.
+ * The FW image has the following sections: @size - 8 bytes of code and
+ * data, followed by 4 bytes of FW version, followed by the 32-bit
+ * 1's complement checksum of the whole image.
+ */
+int t3_load_fw(struct adapter *adapter, const u8 * fw_data, unsigned int size)
+{
+ u32 csum;
+ unsigned int i;
+ const u32 *p = (const u32 *)fw_data;
+ int ret, addr, fw_sector = FW_FLASH_BOOT_ADDR >> 16;
+
+ if (size & 3)
+ return -EINVAL;
+ if (size > FW_VERS_ADDR + 8 - FW_FLASH_BOOT_ADDR)
+ return -EFBIG;
+
+ for (csum = 0, i = 0; i < size / sizeof(csum); i++)
+ csum += ntohl(p[i]);
+ if (csum != 0xffffffff) {
+ CH_ERR(adapter, "corrupted firmware image, checksum %u\n",
+ csum);
+ return -EINVAL;
+ }
+
+ ret = t3_flash_erase_sectors(adapter, fw_sector, fw_sector);
+ if (ret)
+ goto out;
+
+ size -= 8; /* trim off version and checksum */
+ for (addr = FW_FLASH_BOOT_ADDR; size;) {
+ unsigned int chunk_size = min(size, 256U);
+
+ ret = t3_write_flash(adapter, addr, chunk_size, fw_data);
+ if (ret)
+ goto out;
+
+ addr += chunk_size;
+ fw_data += chunk_size;
+ size -= chunk_size;
+ }
+
+ ret = t3_write_flash(adapter, FW_VERS_ADDR, 4, fw_data);
+out:
+ if (ret)
+ CH_ERR(adapter, "firmware download failed, error %d\n", ret);
+ return ret;
+}
+
+#define CIM_CTL_BASE 0x2000
+
+/**
+ * t3_cim_ctl_blk_read - read a block from CIM control region
+ *
+ * @adap: the adapter
+ * @addr: the start address within the CIM control region
+ * @n: number of words to read
+ * @valp: where to store the result
+ *
+ * Reads a block of 4-byte words from the CIM control region.
+ */
+int t3_cim_ctl_blk_read(struct adapter *adap, unsigned int addr,
+ unsigned int n, unsigned int *valp)
+{
+ int ret = 0;
+
+ if (t3_read_reg(adap, A_CIM_HOST_ACC_CTRL) & F_HOSTBUSY)
+ return -EBUSY;
+
+ for ( ; !ret && n--; addr += 4) {
+ t3_write_reg(adap, A_CIM_HOST_ACC_CTRL, CIM_CTL_BASE + addr);
+ ret = t3_wait_op_done(adap, A_CIM_HOST_ACC_CTRL, F_HOSTBUSY,
+ 0, 5, 2);
+ if (!ret)
+ *valp++ = t3_read_reg(adap, A_CIM_HOST_ACC_DATA);
+ }
+ return ret;
+}
+
+
+/**
+ * t3_link_changed - handle interface link changes
+ * @adapter: the adapter
+ * @port_id: the port index that changed link state
+ *
+ * Called when a port's link settings change to propagate the new values
+ * to the associated PHY and MAC. After performing the common tasks it
+ * invokes an OS-specific handler.
+ */
+void t3_link_changed(struct adapter *adapter, int port_id)
+{
+ int link_ok, speed, duplex, fc;
+ struct port_info *pi = adap2pinfo(adapter, port_id);
+ struct cphy *phy = &pi->phy;
+ struct cmac *mac = &pi->mac;
+ struct link_config *lc = &pi->link_config;
+
+ phy->ops->get_link_status(phy, &link_ok, &speed, &duplex, &fc);
+
+ if (link_ok != lc->link_ok && adapter->params.rev > 0 &&
+ uses_xaui(adapter)) {
+ if (link_ok)
+ t3b_pcs_reset(mac);
+ t3_write_reg(adapter, A_XGM_XAUI_ACT_CTRL + mac->offset,
+ link_ok ? F_TXACTENABLE | F_RXEN : 0);
+ }
+ lc->link_ok = (unsigned char)link_ok;
+ lc->speed = speed < 0 ? SPEED_INVALID : speed;
+ lc->duplex = duplex < 0 ? DUPLEX_INVALID : duplex;
+ if (lc->requested_fc & PAUSE_AUTONEG)
+ fc &= lc->requested_fc;
+ else
+ fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
+
+ if (link_ok && speed >= 0 && lc->autoneg == AUTONEG_ENABLE) {
+ /* Set MAC speed, duplex, and flow control to match PHY. */
+ t3_mac_set_speed_duplex_fc(mac, speed, duplex, fc);
+ lc->fc = (unsigned char)fc;
+ }
+
+ t3_os_link_changed(adapter, port_id, link_ok, speed, duplex, fc);
+}
+
+/**
+ * t3_link_start - apply link configuration to MAC/PHY
+ * @phy: the PHY to setup
+ * @mac: the MAC to setup
+ * @lc: the requested link configuration
+ *
+ * Set up a port's MAC and PHY according to a desired link configuration.
+ * - If the PHY can auto-negotiate first decide what to advertise, then
+ * enable/disable auto-negotiation as desired, and reset.
+ * - If the PHY does not auto-negotiate just reset it.
+ * - If auto-negotiation is off set the MAC to the proper speed/duplex/FC,
+ * otherwise do it later based on the outcome of auto-negotiation.
+ */
+int t3_link_start(struct cphy *phy, struct cmac *mac, struct link_config *lc)
+{
+ unsigned int fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
+
+ lc->link_ok = 0;
+ if (lc->supported & SUPPORTED_Autoneg) {
+ lc->advertising &= ~(ADVERTISED_Asym_Pause | ADVERTISED_Pause);
+ if (fc) {
+ lc->advertising |= ADVERTISED_Asym_Pause;
+ if (fc & PAUSE_RX)
+ lc->advertising |= ADVERTISED_Pause;
+ }
+ phy->ops->advertise(phy, lc->advertising);
+
+ if (lc->autoneg == AUTONEG_DISABLE) {
+ lc->speed = lc->requested_speed;
+ lc->duplex = lc->requested_duplex;
+ lc->fc = (unsigned char)fc;
+ t3_mac_set_speed_duplex_fc(mac, lc->speed, lc->duplex,
+ fc);
+ /* Also disables autoneg */
+ phy->ops->set_speed_duplex(phy, lc->speed, lc->duplex);
+ phy->ops->reset(phy, 0);
+ } else
+ phy->ops->autoneg_enable(phy);
+ } else {
+ t3_mac_set_speed_duplex_fc(mac, -1, -1, fc);
+ lc->fc = (unsigned char)fc;
+ phy->ops->reset(phy, 0);
+ }
+ return 0;
+}
+
+/**
+ * t3_set_vlan_accel - control HW VLAN extraction
+ * @adapter: the adapter
+ * @ports: bitmap of adapter ports to operate on
+ * @on: enable (1) or disable (0) HW VLAN extraction
+ *
+ * Enables or disables HW extraction of VLAN tags for the given port.
+ */
+void t3_set_vlan_accel(struct adapter *adapter, unsigned int ports, int on)
+{
+ t3_set_reg_field(adapter, A_TP_OUT_CONFIG,
+ ports << S_VLANEXTRACTIONENABLE,
+ on ? (ports << S_VLANEXTRACTIONENABLE) : 0);
+}
+
+struct intr_info {
+ unsigned int mask; /* bits to check in interrupt status */
+ const char *msg; /* message to print or NULL */
+ short stat_idx; /* stat counter to increment or -1 */
+ unsigned short fatal:1; /* whether the condition reported is fatal */
+};
+
+/**
+ * t3_handle_intr_status - table driven interrupt handler
+ * @adapter: the adapter that generated the interrupt
+ * @reg: the interrupt status register to process
+ * @mask: a mask to apply to the interrupt status
+ * @acts: table of interrupt actions
+ * @stats: statistics counters tracking interrupt occurences
+ *
+ * A table driven interrupt handler that applies a set of masks to an
+ * interrupt status word and performs the corresponding actions if the
+ * interrupts described by the mask have occured. The actions include
+ * optionally printing a warning or alert message, and optionally
+ * incrementing a stat counter. The table is terminated by an entry
+ * specifying mask 0. Returns the number of fatal interrupt conditions.
+ */
+static int t3_handle_intr_status(struct adapter *adapter, unsigned int reg,
+ unsigned int mask,
+ const struct intr_info *acts,
+ unsigned long *stats)
+{
+ int fatal = 0;
+ unsigned int status = t3_read_reg(adapter, reg) & mask;
+
+ for (; acts->mask; ++acts) {
+ if (!(status & acts->mask))
+ continue;
+ if (acts->fatal) {
+ fatal++;
+ CH_ALERT(adapter, "%s (0x%x)\n",
+ acts->msg, status & acts->mask);
+ } else if (acts->msg)
+ CH_WARN(adapter, "%s (0x%x)\n",
+ acts->msg, status & acts->mask);
+ if (acts->stat_idx >= 0)
+ stats[acts->stat_idx]++;
+ }
+ if (status) /* clear processed interrupts */
+ t3_write_reg(adapter, reg, status);
+ return fatal;
+}
+
+#define SGE_INTR_MASK (F_RSPQDISABLED)
+#define MC5_INTR_MASK (F_PARITYERR | F_ACTRGNFULL | F_UNKNOWNCMD | \
+ F_REQQPARERR | F_DISPQPARERR | F_DELACTEMPTY | \
+ F_NFASRCHFAIL)
+#define MC7_INTR_MASK (F_AE | F_UE | F_CE | V_PE(M_PE))
+#define XGM_INTR_MASK (V_TXFIFO_PRTY_ERR(M_TXFIFO_PRTY_ERR) | \
+ V_RXFIFO_PRTY_ERR(M_RXFIFO_PRTY_ERR) | \
+ F_TXFIFO_UNDERRUN | F_RXFIFO_OVERFLOW)
+#define PCIX_INTR_MASK (F_MSTDETPARERR | F_SIGTARABT | F_RCVTARABT | \
+ F_RCVMSTABT | F_SIGSYSERR | F_DETPARERR | \
+ F_SPLCMPDIS | F_UNXSPLCMP | F_RCVSPLCMPERR | \
+ F_DETCORECCERR | F_DETUNCECCERR | F_PIOPARERR | \
+ V_WFPARERR(M_WFPARERR) | V_RFPARERR(M_RFPARERR) | \
+ V_CFPARERR(M_CFPARERR) /* | V_MSIXPARERR(M_MSIXPARERR) */)
+#define PCIE_INTR_MASK (F_UNXSPLCPLERRR | F_UNXSPLCPLERRC | F_PCIE_PIOPARERR |\
+ F_PCIE_WFPARERR | F_PCIE_RFPARERR | F_PCIE_CFPARERR | \
+ /* V_PCIE_MSIXPARERR(M_PCIE_MSIXPARERR) | */ \
+ V_BISTERR(M_BISTERR) | F_PEXERR)
+#define ULPRX_INTR_MASK F_PARERR
+#define ULPTX_INTR_MASK 0
+#define CPLSW_INTR_MASK (F_TP_FRAMING_ERROR | \
+ F_SGE_FRAMING_ERROR | F_CIM_FRAMING_ERROR | \
+ F_ZERO_SWITCH_ERROR)
+#define CIM_INTR_MASK (F_BLKWRPLINT | F_BLKRDPLINT | F_BLKWRCTLINT | \
+ F_BLKRDCTLINT | F_BLKWRFLASHINT | F_BLKRDFLASHINT | \
+ F_SGLWRFLASHINT | F_WRBLKFLASHINT | F_BLKWRBOOTINT | \
+ F_FLASHRANGEINT | F_SDRAMRANGEINT | F_RSVDSPACEINT)
+#define PMTX_INTR_MASK (F_ZERO_C_CMD_ERROR | ICSPI_FRM_ERR | OESPI_FRM_ERR | \
+ V_ICSPI_PAR_ERROR(M_ICSPI_PAR_ERROR) | \
+ V_OESPI_PAR_ERROR(M_OESPI_PAR_ERROR))
+#define PMRX_INTR_MASK (F_ZERO_E_CMD_ERROR | IESPI_FRM_ERR | OCSPI_FRM_ERR | \
+ V_IESPI_PAR_ERROR(M_IESPI_PAR_ERROR) | \
+ V_OCSPI_PAR_ERROR(M_OCSPI_PAR_ERROR))
+#define MPS_INTR_MASK (V_TX0TPPARERRENB(M_TX0TPPARERRENB) | \
+ V_TX1TPPARERRENB(M_TX1TPPARERRENB) | \
+ V_RXTPPARERRENB(M_RXTPPARERRENB) | \
+ V_MCAPARERRENB(M_MCAPARERRENB))
+#define PL_INTR_MASK (F_T3DBG | F_XGMAC0_0 | F_XGMAC0_1 | F_MC5A | F_PM1_TX | \
+ F_PM1_RX | F_ULP2_TX | F_ULP2_RX | F_TP1 | F_CIM | \
+ F_MC7_CM | F_MC7_PMTX | F_MC7_PMRX | F_SGE3 | F_PCIM0 | \
+ F_MPS0 | F_CPL_SWITCH)
+
+/*
+ * Interrupt handler for the PCIX1 module.
+ */
+static void pci_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info pcix1_intr_info[] = {
+ { F_PEXERR, "PCI PEX error", -1, 1 },
+ {F_MSTDETPARERR, "PCI master detected parity error", -1, 1},
+ {F_SIGTARABT, "PCI signaled target abort", -1, 1},
+ {F_RCVTARABT, "PCI received target abort", -1, 1},
+ {F_RCVMSTABT, "PCI received master abort", -1, 1},
+ {F_SIGSYSERR, "PCI signaled system error", -1, 1},
+ {F_DETPARERR, "PCI detected parity error", -1, 1},
+ {F_SPLCMPDIS, "PCI split completion discarded", -1, 1},
+ {F_UNXSPLCMP, "PCI unexpected split completion error", -1, 1},
+ {F_RCVSPLCMPERR, "PCI received split completion error", -1,
+ 1},
+ {F_DETCORECCERR, "PCI correctable ECC error",
+ STAT_PCI_CORR_ECC, 0},
+ {F_DETUNCECCERR, "PCI uncorrectable ECC error", -1, 1},
+ {F_PIOPARERR, "PCI PIO FIFO parity error", -1, 1},
+ {V_WFPARERR(M_WFPARERR), "PCI write FIFO parity error", -1,
+ 1},
+ {V_RFPARERR(M_RFPARERR), "PCI read FIFO parity error", -1,
+ 1},
+ {V_CFPARERR(M_CFPARERR), "PCI command FIFO parity error", -1,
+ 1},
+ {V_MSIXPARERR(M_MSIXPARERR), "PCI MSI-X table/PBA parity "
+ "error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_PCIX_INT_CAUSE, PCIX_INTR_MASK,
+ pcix1_intr_info, adapter->irq_stats))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * Interrupt handler for the PCIE module.
+ */
+static void pcie_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info pcie_intr_info[] = {
+ {F_UNXSPLCPLERRR,
+ "PCI unexpected split completion DMA read error", -1, 1},
+ {F_UNXSPLCPLERRC,
+ "PCI unexpected split completion DMA command error", -1, 1},
+ {F_PCIE_PIOPARERR, "PCI PIO FIFO parity error", -1, 1},
+ {F_PCIE_WFPARERR, "PCI write FIFO parity error", -1, 1},
+ {F_PCIE_RFPARERR, "PCI read FIFO parity error", -1, 1},
+ {F_PCIE_CFPARERR, "PCI command FIFO parity error", -1, 1},
+ {V_PCIE_MSIXPARERR(M_PCIE_MSIXPARERR),
+ "PCI MSI-X table/PBA parity error", -1, 1},
+ {V_BISTERR(M_BISTERR), "PCI BIST error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_PCIE_INT_CAUSE, PCIE_INTR_MASK,
+ pcie_intr_info, adapter->irq_stats))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * TP interrupt handler.
+ */
+static void tp_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info tp_intr_info[] = {
+ {0xffffff, "TP parity error", -1, 1},
+ {0x1000000, "TP out of Rx pages", -1, 1},
+ {0x2000000, "TP out of Tx pages", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_TP_INT_CAUSE, 0xffffffff,
+ tp_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * CIM interrupt handler.
+ */
+static void cim_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info cim_intr_info[] = {
+ {F_RSVDSPACEINT, "CIM reserved space write", -1, 1},
+ {F_SDRAMRANGEINT, "CIM SDRAM address out of range", -1, 1},
+ {F_FLASHRANGEINT, "CIM flash address out of range", -1, 1},
+ {F_BLKWRBOOTINT, "CIM block write to boot space", -1, 1},
+ {F_WRBLKFLASHINT, "CIM write to cached flash space", -1, 1},
+ {F_SGLWRFLASHINT, "CIM single write to flash space", -1, 1},
+ {F_BLKRDFLASHINT, "CIM block read from flash space", -1, 1},
+ {F_BLKWRFLASHINT, "CIM block write to flash space", -1, 1},
+ {F_BLKRDCTLINT, "CIM block read from CTL space", -1, 1},
+ {F_BLKWRCTLINT, "CIM block write to CTL space", -1, 1},
+ {F_BLKRDPLINT, "CIM block read from PL space", -1, 1},
+ {F_BLKWRPLINT, "CIM block write to PL space", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_CIM_HOST_INT_CAUSE, 0xffffffff,
+ cim_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * ULP RX interrupt handler.
+ */
+static void ulprx_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info ulprx_intr_info[] = {
+ {F_PARERR, "ULP RX parity error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_ULPRX_INT_CAUSE, 0xffffffff,
+ ulprx_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * ULP TX interrupt handler.
+ */
+static void ulptx_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info ulptx_intr_info[] = {
+ {F_PBL_BOUND_ERR_CH0, "ULP TX channel 0 PBL out of bounds",
+ STAT_ULP_CH0_PBL_OOB, 0},
+ {F_PBL_BOUND_ERR_CH1, "ULP TX channel 1 PBL out of bounds",
+ STAT_ULP_CH1_PBL_OOB, 0},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_ULPTX_INT_CAUSE, 0xffffffff,
+ ulptx_intr_info, adapter->irq_stats))
+ t3_fatal_err(adapter);
+}
+
+#define ICSPI_FRM_ERR (F_ICSPI0_FIFO2X_RX_FRAMING_ERROR | \
+ F_ICSPI1_FIFO2X_RX_FRAMING_ERROR | F_ICSPI0_RX_FRAMING_ERROR | \
+ F_ICSPI1_RX_FRAMING_ERROR | F_ICSPI0_TX_FRAMING_ERROR | \
+ F_ICSPI1_TX_FRAMING_ERROR)
+#define OESPI_FRM_ERR (F_OESPI0_RX_FRAMING_ERROR | \
+ F_OESPI1_RX_FRAMING_ERROR | F_OESPI0_TX_FRAMING_ERROR | \
+ F_OESPI1_TX_FRAMING_ERROR | F_OESPI0_OFIFO2X_TX_FRAMING_ERROR | \
+ F_OESPI1_OFIFO2X_TX_FRAMING_ERROR)
+
+/*
+ * PM TX interrupt handler.
+ */
+static void pmtx_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info pmtx_intr_info[] = {
+ {F_ZERO_C_CMD_ERROR, "PMTX 0-length pcmd", -1, 1},
+ {ICSPI_FRM_ERR, "PMTX ispi framing error", -1, 1},
+ {OESPI_FRM_ERR, "PMTX ospi framing error", -1, 1},
+ {V_ICSPI_PAR_ERROR(M_ICSPI_PAR_ERROR),
+ "PMTX ispi parity error", -1, 1},
+ {V_OESPI_PAR_ERROR(M_OESPI_PAR_ERROR),
+ "PMTX ospi parity error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_PM1_TX_INT_CAUSE, 0xffffffff,
+ pmtx_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+#define IESPI_FRM_ERR (F_IESPI0_FIFO2X_RX_FRAMING_ERROR | \
+ F_IESPI1_FIFO2X_RX_FRAMING_ERROR | F_IESPI0_RX_FRAMING_ERROR | \
+ F_IESPI1_RX_FRAMING_ERROR | F_IESPI0_TX_FRAMING_ERROR | \
+ F_IESPI1_TX_FRAMING_ERROR)
+#define OCSPI_FRM_ERR (F_OCSPI0_RX_FRAMING_ERROR | \
+ F_OCSPI1_RX_FRAMING_ERROR | F_OCSPI0_TX_FRAMING_ERROR | \
+ F_OCSPI1_TX_FRAMING_ERROR | F_OCSPI0_OFIFO2X_TX_FRAMING_ERROR | \
+ F_OCSPI1_OFIFO2X_TX_FRAMING_ERROR)
+
+/*
+ * PM RX interrupt handler.
+ */
+static void pmrx_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info pmrx_intr_info[] = {
+ {F_ZERO_E_CMD_ERROR, "PMRX 0-length pcmd", -1, 1},
+ {IESPI_FRM_ERR, "PMRX ispi framing error", -1, 1},
+ {OCSPI_FRM_ERR, "PMRX ospi framing error", -1, 1},
+ {V_IESPI_PAR_ERROR(M_IESPI_PAR_ERROR),
+ "PMRX ispi parity error", -1, 1},
+ {V_OCSPI_PAR_ERROR(M_OCSPI_PAR_ERROR),
+ "PMRX ospi parity error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_PM1_RX_INT_CAUSE, 0xffffffff,
+ pmrx_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * CPL switch interrupt handler.
+ */
+static void cplsw_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info cplsw_intr_info[] = {
+/* { F_CIM_OVFL_ERROR, "CPL switch CIM overflow", -1, 1 }, */
+ {F_TP_FRAMING_ERROR, "CPL switch TP framing error", -1, 1},
+ {F_SGE_FRAMING_ERROR, "CPL switch SGE framing error", -1, 1},
+ {F_CIM_FRAMING_ERROR, "CPL switch CIM framing error", -1, 1},
+ {F_ZERO_SWITCH_ERROR, "CPL switch no-switch error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_CPL_INTR_CAUSE, 0xffffffff,
+ cplsw_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+/*
+ * MPS interrupt handler.
+ */
+static void mps_intr_handler(struct adapter *adapter)
+{
+ static const struct intr_info mps_intr_info[] = {
+ {0x1ff, "MPS parity error", -1, 1},
+ {0}
+ };
+
+ if (t3_handle_intr_status(adapter, A_MPS_INT_CAUSE, 0xffffffff,
+ mps_intr_info, NULL))
+ t3_fatal_err(adapter);
+}
+
+#define MC7_INTR_FATAL (F_UE | V_PE(M_PE) | F_AE)
+
+/*
+ * MC7 interrupt handler.
+ */
+static void mc7_intr_handler(struct mc7 *mc7)
+{
+ struct adapter *adapter = mc7->adapter;
+ u32 cause = t3_read_reg(adapter, mc7->offset + A_MC7_INT_CAUSE);
+
+ if (cause & F_CE) {
+ mc7->stats.corr_err++;
+ CH_WARN(adapter, "%s MC7 correctable error at addr 0x%x, "
+ "data 0x%x 0x%x 0x%x\n", mc7->name,
+ t3_read_reg(adapter, mc7->offset + A_MC7_CE_ADDR),
+ t3_read_reg(adapter, mc7->offset + A_MC7_CE_DATA0),
+ t3_read_reg(adapter, mc7->offset + A_MC7_CE_DATA1),
+ t3_read_reg(adapter, mc7->offset + A_MC7_CE_DATA2));
+ }
+
+ if (cause & F_UE) {
+ mc7->stats.uncorr_err++;
+ CH_ALERT(adapter, "%s MC7 uncorrectable error at addr 0x%x, "
+ "data 0x%x 0x%x 0x%x\n", mc7->name,
+ t3_read_reg(adapter, mc7->offset + A_MC7_UE_ADDR),
+ t3_read_reg(adapter, mc7->offset + A_MC7_UE_DATA0),
+ t3_read_reg(adapter, mc7->offset + A_MC7_UE_DATA1),
+ t3_read_reg(adapter, mc7->offset + A_MC7_UE_DATA2));
+ }
+
+ if (G_PE(cause)) {
+ mc7->stats.parity_err++;
+ CH_ALERT(adapter, "%s MC7 parity error 0x%x\n",
+ mc7->name, G_PE(cause));
+ }
+
+ if (cause & F_AE) {
+ u32 addr = 0;
+
+ if (adapter->params.rev > 0)
+ addr = t3_read_reg(adapter,
+ mc7->offset + A_MC7_ERR_ADDR);
+ mc7->stats.addr_err++;
+ CH_ALERT(adapter, "%s MC7 address error: 0x%x\n",
+ mc7->name, addr);
+ }
+
+ if (cause & MC7_INTR_FATAL)
+ t3_fatal_err(adapter);
+
+ t3_write_reg(adapter, mc7->offset + A_MC7_INT_CAUSE, cause);
+}
+
+#define XGM_INTR_FATAL (V_TXFIFO_PRTY_ERR(M_TXFIFO_PRTY_ERR) | \
+ V_RXFIFO_PRTY_ERR(M_RXFIFO_PRTY_ERR))
+/*
+ * XGMAC interrupt handler.
+ */
+static int mac_intr_handler(struct adapter *adap, unsigned int idx)
+{
+ struct cmac *mac = &adap2pinfo(adap, idx)->mac;
+ u32 cause = t3_read_reg(adap, A_XGM_INT_CAUSE + mac->offset);
+
+ if (cause & V_TXFIFO_PRTY_ERR(M_TXFIFO_PRTY_ERR)) {
+ mac->stats.tx_fifo_parity_err++;
+ CH_ALERT(adap, "port%d: MAC TX FIFO parity error\n", idx);
+ }
+ if (cause & V_RXFIFO_PRTY_ERR(M_RXFIFO_PRTY_ERR)) {
+ mac->stats.rx_fifo_parity_err++;
+ CH_ALERT(adap, "port%d: MAC RX FIFO parity error\n", idx);
+ }
+ if (cause & F_TXFIFO_UNDERRUN)
+ mac->stats.tx_fifo_urun++;
+ if (cause & F_RXFIFO_OVERFLOW)
+ mac->stats.rx_fifo_ovfl++;
+ if (cause & V_SERDES_LOS(M_SERDES_LOS))
+ mac->stats.serdes_signal_loss++;
+ if (cause & F_XAUIPCSCTCERR)
+ mac->stats.xaui_pcs_ctc_err++;
+ if (cause & F_XAUIPCSALIGNCHANGE)
+ mac->stats.xaui_pcs_align_change++;
+
+ t3_write_reg(adap, A_XGM_INT_CAUSE + mac->offset, cause);
+ if (cause & XGM_INTR_FATAL)
+ t3_fatal_err(adap);
+ return cause != 0;
+}
+
+/*
+ * Interrupt handler for PHY events.
+ */
+int t3_phy_intr_handler(struct adapter *adapter)
+{
+ static int intr_gpio_bits[] = { 8, 0x20 };
+
+ u32 i, cause = t3_read_reg(adapter, A_T3DBG_INT_CAUSE);
+
+ for_each_port(adapter, i) {
+ if (cause & intr_gpio_bits[i]) {
+ struct cphy *phy = &adap2pinfo(adapter, i)->phy;
+ int phy_cause = phy->ops->intr_handler(phy);
+
+ if (phy_cause & cphy_cause_link_change)
+ t3_link_changed(adapter, i);
+ if (phy_cause & cphy_cause_fifo_error)
+ phy->fifo_errors++;
+ }
+ }
+
+ t3_write_reg(adapter, A_T3DBG_INT_CAUSE, cause);
+ return 0;
+}
+
+/*
+ * T3 slow path (non-data) interrupt handler.
+ */
+int t3_slow_intr_handler(struct adapter *adapter)
+{
+ u32 cause = t3_read_reg(adapter, A_PL_INT_CAUSE0);
+
+ cause &= adapter->slow_intr_mask;
+ if (!cause)
+ return 0;
+ if (cause & F_PCIM0) {
+ if (is_pcie(adapter))
+ pcie_intr_handler(adapter);
+ else
+ pci_intr_handler(adapter);
+ }
+ if (cause & F_SGE3)
+ t3_sge_err_intr_handler(adapter);
+ if (cause & F_MC7_PMRX)
+ mc7_intr_handler(&adapter->pmrx);
+ if (cause & F_MC7_PMTX)
+ mc7_intr_handler(&adapter->pmtx);
+ if (cause & F_MC7_CM)
+ mc7_intr_handler(&adapter->cm);
+ if (cause & F_CIM)
+ cim_intr_handler(adapter);
+ if (cause & F_TP1)
+ tp_intr_handler(adapter);
+ if (cause & F_ULP2_RX)
+ ulprx_intr_handler(adapter);
+ if (cause & F_ULP2_TX)
+ ulptx_intr_handler(adapter);
+ if (cause & F_PM1_RX)
+ pmrx_intr_handler(adapter);
+ if (cause & F_PM1_TX)
+ pmtx_intr_handler(adapter);
+ if (cause & F_CPL_SWITCH)
+ cplsw_intr_handler(adapter);
+ if (cause & F_MPS0)
+ mps_intr_handler(adapter);
+ if (cause & F_MC5A)
+ t3_mc5_intr_handler(&adapter->mc5);
+ if (cause & F_XGMAC0_0)
+ mac_intr_handler(adapter, 0);
+ if (cause & F_XGMAC0_1)
+ mac_intr_handler(adapter, 1);
+ if (cause & F_T3DBG)
+ t3_os_ext_intr_handler(adapter);
+
+ /* Clear the interrupts just processed. */
+ t3_write_reg(adapter, A_PL_INT_CAUSE0, cause);
+ (void)t3_read_reg(adapter, A_PL_INT_CAUSE0); /* flush */
+ return 1;
+}
+
+/**
+ * t3_intr_enable - enable interrupts
+ * @adapter: the adapter whose interrupts should be enabled
+ *
+ * Enable interrupts by setting the interrupt enable registers of the
+ * various HW modules and then enabling the top-level interrupt
+ * concentrator.
+ */
+void t3_intr_enable(struct adapter *adapter)
+{
+ static const struct addr_val_pair intr_en_avp[] = {
+ {A_SG_INT_ENABLE, SGE_INTR_MASK},
+ {A_MC7_INT_ENABLE, MC7_INTR_MASK},
+ {A_MC7_INT_ENABLE - MC7_PMRX_BASE_ADDR + MC7_PMTX_BASE_ADDR,
+ MC7_INTR_MASK},
+ {A_MC7_INT_ENABLE - MC7_PMRX_BASE_ADDR + MC7_CM_BASE_ADDR,
+ MC7_INTR_MASK},
+ {A_MC5_DB_INT_ENABLE, MC5_INTR_MASK},
+ {A_ULPRX_INT_ENABLE, ULPRX_INTR_MASK},
+ {A_TP_INT_ENABLE, 0x3bfffff},
+ {A_PM1_TX_INT_ENABLE, PMTX_INTR_MASK},
+ {A_PM1_RX_INT_ENABLE, PMRX_INTR_MASK},
+ {A_CIM_HOST_INT_ENABLE, CIM_INTR_MASK},
+ {A_MPS_INT_ENABLE, MPS_INTR_MASK},
+ };
+
+ adapter->slow_intr_mask = PL_INTR_MASK;
+
+ t3_write_regs(adapter, intr_en_avp, ARRAY_SIZE(intr_en_avp), 0);
+
+ if (adapter->params.rev > 0) {
+ t3_write_reg(adapter, A_CPL_INTR_ENABLE,
+ CPLSW_INTR_MASK | F_CIM_OVFL_ERROR);
+ t3_write_reg(adapter, A_ULPTX_INT_ENABLE,
+ ULPTX_INTR_MASK | F_PBL_BOUND_ERR_CH0 |
+ F_PBL_BOUND_ERR_CH1);
+ } else {
+ t3_write_reg(adapter, A_CPL_INTR_ENABLE, CPLSW_INTR_MASK);
+ t3_write_reg(adapter, A_ULPTX_INT_ENABLE, ULPTX_INTR_MASK);
+ }
+
+ t3_write_reg(adapter, A_T3DBG_GPIO_ACT_LOW,
+ adapter_info(adapter)->gpio_intr);
+ t3_write_reg(adapter, A_T3DBG_INT_ENABLE,
+ adapter_info(adapter)->gpio_intr);
+ if (is_pcie(adapter))
+ t3_write_reg(adapter, A_PCIE_INT_ENABLE, PCIE_INTR_MASK);
+ else
+ t3_write_reg(adapter, A_PCIX_INT_ENABLE, PCIX_INTR_MASK);
+ t3_write_reg(adapter, A_PL_INT_ENABLE0, adapter->slow_intr_mask);
+ (void)t3_read_reg(adapter, A_PL_INT_ENABLE0); /* flush */
+}
+
+/**
+ * t3_intr_disable - disable a card's interrupts
+ * @adapter: the adapter whose interrupts should be disabled
+ *
+ * Disable interrupts. We only disable the top-level interrupt
+ * concentrator and the SGE data interrupts.
+ */
+void t3_intr_disable(struct adapter *adapter)
+{
+ t3_write_reg(adapter, A_PL_INT_ENABLE0, 0);
+ (void)t3_read_reg(adapter, A_PL_INT_ENABLE0); /* flush */
+ adapter->slow_intr_mask = 0;
+}
+
+/**
+ * t3_intr_clear - clear all interrupts
+ * @adapter: the adapter whose interrupts should be cleared
+ *
+ * Clears all interrupts.
+ */
+void t3_intr_clear(struct adapter *adapter)
+{
+ static unsigned int cause_reg_addr[] = {
+ A_SG_INT_CAUSE,
+ A_SG_RSPQ_FL_STATUS,
+ A_PCIX_INT_CAUSE,
+ A_MC7_INT_CAUSE,
+ A_MC7_INT_CAUSE - MC7_PMRX_BASE_ADDR + MC7_PMTX_BASE_ADDR,
+ A_MC7_INT_CAUSE - MC7_PMRX_BASE_ADDR + MC7_CM_BASE_ADDR,
+ A_CIM_HOST_INT_CAUSE,
+ A_TP_INT_CAUSE,
+ A_MC5_DB_INT_CAUSE,
+ A_ULPRX_INT_CAUSE,
+ A_ULPTX_INT_CAUSE,
+ A_CPL_INTR_CAUSE,
+ A_PM1_TX_INT_CAUSE,
+ A_PM1_RX_INT_CAUSE,
+ A_MPS_INT_CAUSE,
+ A_T3DBG_INT_CAUSE,
+ };
+ unsigned int i;
+
+ /* Clear PHY and MAC interrupts for each port. */
+ for_each_port(adapter, i)
+ t3_port_intr_clear(adapter, i);
+
+ for (i = 0; i < ARRAY_SIZE(cause_reg_addr); ++i)
+ t3_write_reg(adapter, cause_reg_addr[i], 0xffffffff);
+
+ t3_write_reg(adapter, A_PL_INT_CAUSE0, 0xffffffff);
+ (void)t3_read_reg(adapter, A_PL_INT_CAUSE0); /* flush */
+}
+
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2006-12-14 07:35    [W:0.067 / U:14.692 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site