lkml.org 
[lkml]   [2005]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Date
    From
    SubjectRe: 2.6.13-rc3-mm3
    Andrew Morton schrieb:
    > Michael Thonke <iogl64nx@gmail.com> wrote:
    >> here again I have two problems. With 2.6.13-rc3-mm3 I have problems
    >> using my SATA drives on Intel ICH6.
    >> The kernel can't route there IRQs or can't discover them. the option
    >> irqpoll got them to work now.
    >> The problem is new because 2.6.13-rc3[-mm1,mm2] work without any problems.
    >
    > OK. Please generate the full dmesg output for -mm2 and for -mm3 and run
    > `diff -u dmesg.mm2 dmesg.mm3' and send it? And keep those files because we
    > may end up needing to add them to an acpi bugzilla entry ;)

    Well I did a little mistake..it only worked correctly up to
    2.6.13-rc3-mm1 but this dmesg output I have.

    Well as I save mm[2,3] are unable to setup the correct IRQs for the
    devices..and please note that 2.6.13-rc3-mm3 only booted with irqpoll so
    its in the dmesg output "dmesg.mm3"
    Normaly the IRQ routed to something about 1xx now they are 1-21?! Caused
    by irqpoll?



    >
    >> The SATA drives are Samsung HD160JJ SATAII. The mainboard I use is a
    >> ASUS P4GPL-X.
    >>
    >> Second one is about Intel HD-Codec (snd-hda-intel) on modprobe when
    >> loading the module it gives me
    >>
    >> ---> snip
    >> hda_codec: Unknown model for ALC880, trying auto-probe from BIOS...
    >
    > Does -mm2 print that `unknown model' message?

    Yes and mm1 it's a wide problem as I found many posts on ALSA Forums
    But the big problem behind is...after it oops
    My Linux Raid (md) goes bad then..at reboot it gives me more oops and
    all changes on FS (reiser4) lost..and if I wouldn't use snd-hda-intel as
    modul the hole system hung at boot.

    >
    >> Unable to handle kernel NULL pointer dereference at virtual address 00000000
    >> printing eip:
    >> f88713f4
    >> *pde = 00000000
    >> Oops: 0002 [#1]
    >> PREEMPT
    >> last sysfs file:
    >> Modules linked in: snd_hda_intel snd_hda_codec nvidia
    >> CPU: 0
    >> EIP: 0060:[<f88713f4>] Tainted: P VLI
    >
    > Please verify that it happens without the nvidia module loaded.
    >
    >> EFLAGS: 00010293 (2.6.13-rc3-mm3pm)
    >> eax: fffffffe ebx: f3b33548 ecx: 00000000 edx: 00000000
    >> esi: f3b33400 edi: 00000000 ebp: 00000006 esp: f0371ddc
    >> ds: 007b es: 007b ss: 0068
    >> Process modprobe (pid: 7398, threadinfo=f0370000 task=f4183560)
    >> Stack: 00000000 00000000 00000000 00000000 f3b33400 f3b33548 f0f1d000
    >> f8871933
    >> f3b33400 f0f1d000 f8871bbd f8875478 f88748f6 00000001 f886d77e
    >> 00000f00
    >> 00000005 00000000 f0f1d000 f54d04c0 00000000 f886d984 00000f00
    >> 00000002
    >> Call Trace:
    >> [<f8871933>]
    >> [<f8871bbd>]
    >
    > Odd trace. Do you have CONFIG_KALLSYMS enabled? If not, please turn it on.

    Mh I tried but my system freezes on boot then. And screen leaves blank.
    >

    Thank you Andrew and the other for the great help up to here.

    Greets

    Best regards
    Michael

    --- dmesg.mm1 2005-07-29 13:47:58.878442480 +0000
    +++ dmesg.mm3 2005-07-29 13:54:03.272355896 +0000
    @@ -1,43 +1,13 @@
    -Linux version 2.6.13-rc3-mm1pm (root@ioGL64NX_32) (gcc-Version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #1 PREEMPT Fri Jul 29 13:34:49 Local time zone must be set--see
    -BIOS-provided physical RAM map:
    - BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    - BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    - BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    - BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
    - BIOS-e820: 000000003ffb0000 - 000000003ffbe000 (ACPI data)
    - BIOS-e820: 000000003ffbe000 - 000000003fff0000 (ACPI NVS)
    - BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
    - BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
    -127MB HIGHMEM available.
    -896MB LOWMEM available.
    -found SMP MP-table at 000ff780
    -On node 0 totalpages: 262064
    - DMA zone: 4096 pages, LIFO batch:1
    - Normal zone: 225280 pages, LIFO batch:31
    - HighMem zone: 32688 pages, LIFO batch:15
    -DMI 2.3 present.
    -Intel MultiProcessor Specification v1.1
    - Virtual Wire compatibility mode.
    -OEM ID: INTEL Product ID: APIC at: 0xFEE00000
    -Processor #0 6:13 APIC version 20
    -I/O APIC #1 Version 32 at 0xFEC00000.
    -Enabling APIC mode: Flat. Using 1 I/O APICs
    -Processors: 1
    -Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
    -Built 1 zonelists
    -mapped APIC to ffffd000 (fee00000)
    -mapped IOAPIC to ffffc000 (fec00000)
    -Initializing CPU#0
    -Kernel command line: root=/dev/md1 vga=794 quiet
    +ormance
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    -Detected 1605.958 MHz processor.
    -Using tsc for high-res timesource
    +Detected 1605.994 MHz processor.
    +Using pmtmr for high-res timesource
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    -Memory: 1034508k/1048256k available (2702k kernel code, 12980k reserved, 839k data, 168k init, 130752k highmem)
    +Memory: 1034260k/1048256k available (3050k kernel code, 13228k reserved, 670k data, 200k init, 130752k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    -Calibrating delay using timer specific routine.. 3214.33 BogoMIPS (lpj=1607165)
    +Calibrating delay using timer specific routine.. 3215.31 BogoMIPS (lpj=1607658)
    Security Framework v1.0.0 initialized
    Capability LSM initialized
    Mount-cache hash table entries: 512
    @@ -53,10 +23,18 @@
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    + ACPI-0287: *** Error: Region SystemMemory(0) has no handler
    + ACPI-0127: *** Error: acpi_load_tables: Could not load namespace: AE_NOT_EXIST
    + ACPI-0136: *** Error: acpi_load_tables: Could not load tables: AE_NOT_EXIST
    +ACPI: Unable to load the System Description Tables
    ENABLING IO-APIC IRQs
    -..TIMER: vector=0x31 pin1=2 pin2=0
    +..TIMER: vector=0x31 pin1=2 pin2=-1
    NET: Registered protocol family 16
    PCI: Using configuration type 1
    +ACPI: Subsystem revision 20050708
    +ACPI: Interpreter disabled.
    +Linux Plug and Play Support v0.97 (c) Adam Belay
    +pnp: PnP ACPI: disabled
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    @@ -67,31 +45,70 @@
    PCI: Transparent bridge - 0000:00:1e.0
    PCI: Discovered primary peer bus ff [IRQ]
    PCI: Using IRQ router PIIX/ICH [8086/2640] at 0000:00:1f.0
    -PCI->APIC IRQ transform: 0000:00:01.0[A] -> IRQ 129
    -PCI->APIC IRQ transform: 0000:00:1c.0[A] -> IRQ 129
    -PCI->APIC IRQ transform: 0000:00:1c.1[B] -> IRQ 137
    -PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 161
    -PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 153
    -PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 145
    -PCI->APIC IRQ transform: 0000:00:1d.3[D] -> IRQ 129
    -PCI->APIC IRQ transform: 0000:00:1d.7[A] -> IRQ 161
    -PCI->APIC IRQ transform: 0000:00:1f.1[A] -> IRQ 145
    -PCI->APIC IRQ transform: 0000:00:1f.2[B] -> IRQ 153
    -PCI->APIC IRQ transform: 0000:00:1f.3[B] -> IRQ 153
    -PCI->APIC IRQ transform: 0000:04:00.0[A] -> IRQ 129
    -PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 137
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 4!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI BIOS passed nonexistent PCI bus 2!
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: Bridge: 0000:00:01.0
    + IO window: e000-efff
    + MEM window: d2f00000-d7ffffff
    + PREFETCH window: d8000000-dfffffff
    +PCI: Bridge: 0000:00:1c.0
    + IO window: d000-dfff
    + MEM window: disabled.
    + PREFETCH window: disabled.
    +PCI: Bridge: 0000:00:1c.1
    + IO window: c000-cfff
    + MEM window: d2e00000-d2efffff
    + PREFETCH window: 40000000-400fffff
    +PCI: Bridge: 0000:00:1e.0
    + IO window: b000-bfff
    + MEM window: disabled.
    + PREFETCH window: disabled.
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: No IRQ known for interrupt pin A of device 0000:00:01.0. Probably buggy MP table.
    +PCI: Setting latency timer of device 0000:00:01.0 to 64
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0. Probably buggy MP table.
    +PCI: Setting latency timer of device 0000:00:1c.0 to 64
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: No IRQ known for interrupt pin B of device 0000:00:1c.1. Probably buggy MP table.
    +PCI: Setting latency timer of device 0000:00:1c.1 to 64
    +PCI: Setting latency timer of device 0000:00:1e.0 to 64
    Machine check exception polling timer started.
    +apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    highmem bounce pool size: 64 pages
    fuse init (API version 7.1)
    Initializing Cryptographic API
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: No IRQ known for interrupt pin A of device 0000:00:01.0. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    +pcie_portdrv_probe->Dev[2581:8086] has invalid IRQ. Check vendor BIOS
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    +pcie_portdrv_probe->Dev[2660:8086] has invalid IRQ. Check vendor BIOS
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    +PCI BIOS passed nonexistent PCI bus 0!
    +PCI: No IRQ known for interrupt pin B of device 0000:00:1c.1. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    +pcie_portdrv_probe->Dev[2662:8086] has invalid IRQ. Check vendor BIOS
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    @@ -100,6 +117,7 @@
    vesafb: protected mode interface info at c000:d620
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    +vesafb: Mode is VGA compatible
    Console: switching to colour frame buffer device 160x64
    fb0: VESA VGA frame buffer device
    fb1: Virtual frame buffer device, using 1024K of video memory
    @@ -115,7 +133,7 @@
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
    loop: loaded (max 8 devices)
    -ub: sizeof ub_scsi_cmd 68 ub_dev 2384 ub_lun 140
    +ub: sizeof ub_scsi_cmd 68 ub_dev 2388 ub_lun 140
    usbcore: registered new driver ub
    sk98lin: Network Device Driver v8.23.1.3
    (C)Copyright 1999-2005 Marvell(R).
    @@ -126,6 +144,7 @@
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH6: IDE controller at PCI slot 0000:00:1f.1
    +PCI BIOS passed nonexistent PCI bus 0!
    ICH6: chipset revision 5
    ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    @@ -141,8 +160,8 @@
    libata version 1.11 loaded.
    ata_piix version 1.03
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    -ata1: SATA max UDMA/133 cmd 0xAC00 ctl 0xA882 bmdma 0xA400 irq 153
    -ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA482 bmdma 0xA408 irq 153
    +ata1: SATA max UDMA/133 cmd 0xAC00 ctl 0xA882 bmdma 0xA400 irq 3
    +ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA482 bmdma 0xA408 irq 3
    ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata1: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata1: dev 0 configured for UDMA/133
    @@ -171,39 +190,39 @@
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    usbmon: debugs is not available
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    -ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
    +ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 01010001)
    ehci_hcd 0000:00:1d.7: continuing after BIOS bug...
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    -ehci_hcd 0000:00:1d.7: irq 161, io mem 0xd2dffc00
    +ehci_hcd 0000:00:1d.7: irq 11, io mem 0xd2dffc00
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    USB Universal Host Controller Interface driver v2.3
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    -uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
    +uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    -uhci_hcd 0000:00:1d.0: irq 161, io base 0x00009880
    +uhci_hcd 0000:00:1d.0: irq 11, io base 0x00009880
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    -uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
    +uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    -uhci_hcd 0000:00:1d.1: irq 153, io base 0x00009c00
    +uhci_hcd 0000:00:1d.1: irq 3, io base 0x00009c00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    -uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
    +uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    -uhci_hcd 0000:00:1d.2: irq 145, io base 0x0000a000
    +uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000a000
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    -uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
    +uhci_hcd 0000:00:1d.3: UHCI Host Controller
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    -uhci_hcd 0000:00:1d.3: irq 129, io base 0x0000a080
    +uhci_hcd 0000:00:1d.3: irq 10, io base 0x0000a080
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usbcore: registered new driver usblp
    @@ -213,16 +232,28 @@
    usb 2-2: new low speed USB device using uhci_hcd and address 3
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    -usb 4-1: new full speed USB device using uhci_hcd and address 2
    input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Mouse [Genius NetScroll+Mini Traveler] on usb-0000:00:1d.0-2
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    +usb 4-1: new full speed USB device using uhci_hcd and address 2
    +usbcore: registered new driver usbserial
    +drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
    +usbcore: registered new driver usbserial_generic
    +drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
    +drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
    +pl2303 4-1:1.0: PL-2303 converter detected
    +usb 4-1: PL-2303 converter now attached to ttyUSB0
    +usbcore: registered new driver pl2303
    +drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.12
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 3.38
    +Advanced Linux Sound Architecture Driver Version 1.0.9 (Sun May 29 07:31:02 2005 UTC).
    +ALSA device list:
    + No soundcards found.
    NET: Registered protocol family 2
    IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
    TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
    @@ -309,7 +340,7 @@
    raid0 : Allocating 4 bytes for hash.
    md: ... autorun DONE.
    VFS: Mounted root (reiser4 filesystem) readonly.
    -Freeing unused kernel memory: 168k freed
    +Freeing unused kernel memory: 200k freed
    ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
    ReiserFS: sdb1: using ordered data mode
    ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    Linux version 2.6.13-rc3-mm1pm (root@ioGL64NX_32) (gcc-Version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #1 PREEMPT Fri Jul 29 13:34:49 Local time zone must be set--see
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
    BIOS-e820: 000000003ffb0000 - 000000003ffbe000 (ACPI data)
    BIOS-e820: 000000003ffbe000 - 000000003fff0000 (ACPI NVS)
    BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
    BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
    127MB HIGHMEM available.
    896MB LOWMEM available.
    found SMP MP-table at 000ff780
    On node 0 totalpages: 262064
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 225280 pages, LIFO batch:31
    HighMem zone: 32688 pages, LIFO batch:15
    DMI 2.3 present.
    Intel MultiProcessor Specification v1.1
    Virtual Wire compatibility mode.
    OEM ID: INTEL Product ID: APIC at: 0xFEE00000
    Processor #0 6:13 APIC version 20
    I/O APIC #1 Version 32 at 0xFEC00000.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Processors: 1
    Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
    Built 1 zonelists
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Initializing CPU#0
    Kernel command line: root=/dev/md1 vga=794 quiet
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    Detected 1605.958 MHz processor.
    Using tsc for high-res timesource
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 1034508k/1048256k available (2702k kernel code, 12980k reserved, 839k data, 168k init, 130752k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3214.33 BogoMIPS (lpj=1607165)
    Security Framework v1.0.0 initialized
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000180 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    mtrr: v2.0 (20020519)
    CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 pin1=2 pin2=0
    NET: Registered protocol family 16
    PCI: Using configuration type 1
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Probing PCI hardware
    PCI: Probing PCI hardware (bus 00)
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    Boot video device is 0000:04:00.0
    PCI: Transparent bridge - 0000:00:1e.0
    PCI: Discovered primary peer bus ff [IRQ]
    PCI: Using IRQ router PIIX/ICH [8086/2640] at 0000:00:1f.0
    PCI->APIC IRQ transform: 0000:00:01.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1c.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1c.1[B] -> IRQ 137
    PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 161
    PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 153
    PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 145
    PCI->APIC IRQ transform: 0000:00:1d.3[D] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1d.7[A] -> IRQ 161
    PCI->APIC IRQ transform: 0000:00:1f.1[A] -> IRQ 145
    PCI->APIC IRQ transform: 0000:00:1f.2[B] -> IRQ 153
    PCI->APIC IRQ transform: 0000:00:1f.3[B] -> IRQ 153
    PCI->APIC IRQ transform: 0000:04:00.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 137
    Machine check exception polling timer started.
    highmem bounce pool size: 64 pages
    fuse init (API version 7.1)
    Initializing Cryptographic API
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 5120k, total 131072k
    vesafb: mode is 1280x1024x16, linelength=2560, pages=1
    vesafb: protected mode interface info at c000:d620
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 160x64
    fb0: VESA VGA frame buffer device
    fb1: Virtual frame buffer device, using 1024K of video memory
    Real Time Clock Driver v1.12
    i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
    i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
    cn_fork is registered
    cn_exit is registered
    mice: PS/2 mouse device common for all mice
    io scheduler noop registered
    io scheduler cfq registered
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
    loop: loaded (max 8 devices)
    ub: sizeof ub_scsi_cmd 68 ub_dev 2384 ub_lun 140
    usbcore: registered new driver ub
    sk98lin: Network Device Driver v8.23.1.3
    (C)Copyright 1999-2005 Marvell(R).
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
    PrefPort:A RlmtMode:Check Link State
    netconsole: not configured, aborting
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH6: IDE controller at PCI slot 0000:00:1f.1
    ICH6: chipset revision 5
    ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
    Probing IDE interface ide0...
    hda: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
    hdb: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
    libata version 1.11 loaded.
    ata_piix version 1.03
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ata1: SATA max UDMA/133 cmd 0xAC00 ctl 0xA882 bmdma 0xA400 irq 153
    ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA482 bmdma 0xA408 irq 153
    ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata1: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata1: dev 0 configured for UDMA/133
    scsi0 : ata_piix
    ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata2: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata2: dev 0 configured for UDMA/133
    scsi1 : ata_piix
    Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
    Type: Direct-Access ANSI SCSI revision: 05
    Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    sda: sda1 sda2 < sda5 sda6 sda7 >
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 >
    Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    usbmon: debugs is not available
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 01010001)
    ehci_hcd 0000:00:1d.7: continuing after BIOS bug...
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: irq 161, io mem 0xd2dffc00
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    USB Universal Host Controller Interface driver v2.3
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 161, io base 0x00009880
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 153, io base 0x00009c00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 145, io base 0x0000a000
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 129, io base 0x0000a080
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usbcore: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    usb 2-1: new low speed USB device using uhci_hcd and address 2
    usb 2-2: new low speed USB device using uhci_hcd and address 3
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb 4-1: new full speed USB device using uhci_hcd and address 2
    input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Mouse [Genius NetScroll+Mini Traveler] on usb-0000:00:1d.0-2
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 3.38
    NET: Registered protocol family 2
    IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
    TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
    TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI Shortcut mode
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering sdb7 ...
    md: adding sdb7 ...
    md: sdb6 has different UUID to sdb7
    md: sdb5 has different UUID to sdb7
    md: sda7 has different UUID to sdb7
    md: adding sda6 ...
    md: sda5 has different UUID to sdb7
    md: created md2
    md: bind<sda6>
    md: bind<sdb7>
    md: running: <sdb7><sda6>
    md2: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb7
    raid0: comparing sdb7(20000768) with sdb7(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda6
    raid0: comparing sda6(20000768) with sdb7(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: considering sdb6 ...
    md: adding sdb6 ...
    md: sdb5 has different UUID to sdb6
    md: sda7 has different UUID to sdb6
    md: adding sda5 ...
    md: created md0
    md: bind<sda5>
    md: bind<sdb6>
    md: running: <sdb6><sda5>
    md0: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb6
    raid0: comparing sdb6(20000768) with sdb6(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda5
    raid0: comparing sda5(20000768) with sdb6(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: considering sdb5 ...
    md: adding sdb5 ...
    md: adding sda7 ...
    md: created md1
    md: bind<sda7>
    md: bind<sdb5>
    md: running: <sdb5><sda7>
    md1: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb5
    raid0: comparing sdb5(20000768) with sdb5(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda7
    raid0: comparing sda7(20000768) with sdb5(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: ... autorun DONE.
    VFS: Mounted root (reiser4 filesystem) readonly.
    Freeing unused kernel memory: 168k freed
    ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
    ReiserFS: sdb1: using ordered data mode
    ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sdb1: checking transaction log (sdb1)
    ReiserFS: sdb1: Using r5 hash to sort names
    eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    tcp offload: enabled
    scatter-gather: enabled
    tx-checksum: enabled
    rx-checksum: enabled
    rx-polling: enabled

    ormance
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    Detected 1605.994 MHz processor.
    Using pmtmr for high-res timesource
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 1034260k/1048256k available (3050k kernel code, 13228k reserved, 670k data, 200k init, 130752k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3215.31 BogoMIPS (lpj=1607658)
    Security Framework v1.0.0 initialized
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000180 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    mtrr: v2.0 (20020519)
    CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ACPI-0287: *** Error: Region SystemMemory(0) has no handler
    ACPI-0127: *** Error: acpi_load_tables: Could not load namespace: AE_NOT_EXIST
    ACPI-0136: *** Error: acpi_load_tables: Could not load tables: AE_NOT_EXIST
    ACPI: Unable to load the System Description Tables
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 pin1=2 pin2=-1
    NET: Registered protocol family 16
    PCI: Using configuration type 1
    ACPI: Subsystem revision 20050708
    ACPI: Interpreter disabled.
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI: disabled
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Probing PCI hardware
    PCI: Probing PCI hardware (bus 00)
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    Boot video device is 0000:04:00.0
    PCI: Transparent bridge - 0000:00:1e.0
    PCI: Discovered primary peer bus ff [IRQ]
    PCI: Using IRQ router PIIX/ICH [8086/2640] at 0000:00:1f.0
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 4!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI BIOS passed nonexistent PCI bus 2!
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: Bridge: 0000:00:01.0
    IO window: e000-efff
    MEM window: d2f00000-d7ffffff
    PREFETCH window: d8000000-dfffffff
    PCI: Bridge: 0000:00:1c.0
    IO window: d000-dfff
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI: Bridge: 0000:00:1c.1
    IO window: c000-cfff
    MEM window: d2e00000-d2efffff
    PREFETCH window: 40000000-400fffff
    PCI: Bridge: 0000:00:1e.0
    IO window: b000-bfff
    MEM window: disabled.
    PREFETCH window: disabled.
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: No IRQ known for interrupt pin A of device 0000:00:01.0. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: No IRQ known for interrupt pin B of device 0000:00:1c.1. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    PCI: Setting latency timer of device 0000:00:1e.0 to 64
    Machine check exception polling timer started.
    apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    highmem bounce pool size: 64 pages
    fuse init (API version 7.1)
    Initializing Cryptographic API
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: No IRQ known for interrupt pin A of device 0000:00:01.0. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    pcie_portdrv_probe->Dev[2581:8086] has invalid IRQ. Check vendor BIOS
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    pcie_portdrv_probe->Dev[2660:8086] has invalid IRQ. Check vendor BIOS
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    PCI BIOS passed nonexistent PCI bus 0!
    PCI: No IRQ known for interrupt pin B of device 0000:00:1c.1. Probably buggy MP table.
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    pcie_portdrv_probe->Dev[2662:8086] has invalid IRQ. Check vendor BIOS
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 5120k, total 131072k
    vesafb: mode is 1280x1024x16, linelength=2560, pages=1
    vesafb: protected mode interface info at c000:d620
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    vesafb: Mode is VGA compatible
    Console: switching to colour frame buffer device 160x64
    fb0: VESA VGA frame buffer device
    fb1: Virtual frame buffer device, using 1024K of video memory
    Real Time Clock Driver v1.12
    i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
    i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
    cn_fork is registered
    cn_exit is registered
    mice: PS/2 mouse device common for all mice
    io scheduler noop registered
    io scheduler cfq registered
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
    loop: loaded (max 8 devices)
    ub: sizeof ub_scsi_cmd 68 ub_dev 2388 ub_lun 140
    usbcore: registered new driver ub
    sk98lin: Network Device Driver v8.23.1.3
    (C)Copyright 1999-2005 Marvell(R).
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
    PrefPort:A RlmtMode:Check Link State
    netconsole: not configured, aborting
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH6: IDE controller at PCI slot 0000:00:1f.1
    PCI BIOS passed nonexistent PCI bus 0!
    ICH6: chipset revision 5
    ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
    Probing IDE interface ide0...
    hda: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
    hdb: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
    libata version 1.11 loaded.
    ata_piix version 1.03
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ata1: SATA max UDMA/133 cmd 0xAC00 ctl 0xA882 bmdma 0xA400 irq 3
    ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA482 bmdma 0xA408 irq 3
    ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata1: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata1: dev 0 configured for UDMA/133
    scsi0 : ata_piix
    ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata2: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata2: dev 0 configured for UDMA/133
    scsi1 : ata_piix
    Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
    Type: Direct-Access ANSI SCSI revision: 05
    Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    sda: sda1 sda2 < sda5 sda6 sda7 >
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 >
    Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    usbmon: debugs is not available
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: EHCI Host Controller
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 01010001)
    ehci_hcd 0000:00:1d.7: continuing after BIOS bug...
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: irq 11, io mem 0xd2dffc00
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    USB Universal Host Controller Interface driver v2.3
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: UHCI Host Controller
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 11, io base 0x00009880
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: UHCI Host Controller
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 3, io base 0x00009c00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: UHCI Host Controller
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000a000
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: UHCI Host Controller
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 10, io base 0x0000a080
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usbcore: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    usb 2-1: new low speed USB device using uhci_hcd and address 2
    usb 2-2: new low speed USB device using uhci_hcd and address 3
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Mouse [Genius NetScroll+Mini Traveler] on usb-0000:00:1d.0-2
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    usb 4-1: new full speed USB device using uhci_hcd and address 2
    usbcore: registered new driver usbserial
    drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
    usbcore: registered new driver usbserial_generic
    drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
    drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
    pl2303 4-1:1.0: PL-2303 converter detected
    usb 4-1: PL-2303 converter now attached to ttyUSB0
    usbcore: registered new driver pl2303
    drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.12
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 3.38
    Advanced Linux Sound Architecture Driver Version 1.0.9 (Sun May 29 07:31:02 2005 UTC).
    ALSA device list:
    No soundcards found.
    NET: Registered protocol family 2
    IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
    TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
    TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI Shortcut mode
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering sdb7 ...
    md: adding sdb7 ...
    md: sdb6 has different UUID to sdb7
    md: sdb5 has different UUID to sdb7
    md: sda7 has different UUID to sdb7
    md: adding sda6 ...
    md: sda5 has different UUID to sdb7
    md: created md2
    md: bind<sda6>
    md: bind<sdb7>
    md: running: <sdb7><sda6>
    md2: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb7
    raid0: comparing sdb7(20000768) with sdb7(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda6
    raid0: comparing sda6(20000768) with sdb7(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: considering sdb6 ...
    md: adding sdb6 ...
    md: sdb5 has different UUID to sdb6
    md: sda7 has different UUID to sdb6
    md: adding sda5 ...
    md: created md0
    md: bind<sda5>
    md: bind<sdb6>
    md: running: <sdb6><sda5>
    md0: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb6
    raid0: comparing sdb6(20000768) with sdb6(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda5
    raid0: comparing sda5(20000768) with sdb6(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: considering sdb5 ...
    md: adding sdb5 ...
    md: adding sda7 ...
    md: created md1
    md: bind<sda7>
    md: bind<sdb5>
    md: running: <sdb5><sda7>
    md1: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb5
    raid0: comparing sdb5(20000768) with sdb5(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda7
    raid0: comparing sda7(20000768) with sdb5(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: ... autorun DONE.
    VFS: Mounted root (reiser4 filesystem) readonly.
    Freeing unused kernel memory: 200k freed
    ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
    ReiserFS: sdb1: using ordered data mode
    ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sdb1: checking transaction log (sdb1)
    ReiserFS: sdb1: Using r5 hash to sort names
    eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    tcp offload: enabled
    scatter-gather: enabled
    tx-checksum: enabled
    rx-checksum: enabled
    rx-polling: enabled

    fb0000 (usable)
    BIOS-e820: 000000003ffb0000 - 000000003ffbe000 (ACPI data)
    BIOS-e820: 000000003ffbe000 - 000000003fff0000 (ACPI NVS)
    BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
    BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
    127MB HIGHMEM available.
    896MB LOWMEM available.
    found SMP MP-table at 000ff780
    On node 0 totalpages: 262064
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 225280 pages, LIFO batch:31
    HighMem zone: 32688 pages, LIFO batch:15
    DMI 2.3 present.
    Intel MultiProcessor Specification v1.1
    Virtual Wire compatibility mode.
    OEM ID: INTEL Product ID: APIC at: 0xFEE00000
    Processor #0 6:13 APIC version 20
    I/O APIC #1 Version 32 at 0xFEC00000.
    Enabling APIC mode: Flat. Using 1 I/O APICs
    Processors: 1
    Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
    Built 1 zonelists
    mapped APIC to ffffd000 (fee00000)
    mapped IOAPIC to ffffc000 (fec00000)
    Initializing CPU#0
    Kernel command line: root=/dev/md1 vga=794 quiet
    PID hash table entries: 4096 (order: 12, 65536 bytes)
    Detected 1606.130 MHz processor.
    Using tsc for high-res timesource
    Console: colour dummy device 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 1034508k/1048256k available (2702k kernel code, 12980k reserved, 839k data, 168k init, 130752k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay using timer specific routine.. 3214.30 BogoMIPS (lpj=1607154)
    Security Framework v1.0.0 initialized
    Capability LSM initialized
    Mount-cache hash table entries: 512
    CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000
    CPU: L1 I cache: 32K, L1 D cache: 32K
    CPU: L2 cache: 2048K
    CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000180 00000000 00000000
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    mtrr: v2.0 (20020519)
    CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ENABLING IO-APIC IRQs
    ..TIMER: vector=0x31 pin1=2 pin2=0
    NET: Registered protocol family 16
    PCI: Using configuration type 1
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Probing PCI hardware
    PCI: Probing PCI hardware (bus 00)
    PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
    Boot video device is 0000:04:00.0
    PCI: Transparent bridge - 0000:00:1e.0
    PCI: Discovered primary peer bus ff [IRQ]
    PCI: Using IRQ router PIIX/ICH [8086/2640] at 0000:00:1f.0
    PCI->APIC IRQ transform: 0000:00:01.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1b.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1c.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1c.1[B] -> IRQ 137
    PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 161
    PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 153
    PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 145
    PCI->APIC IRQ transform: 0000:00:1d.3[D] -> IRQ 129
    PCI->APIC IRQ transform: 0000:00:1d.7[A] -> IRQ 161
    PCI->APIC IRQ transform: 0000:00:1f.1[A] -> IRQ 145
    PCI->APIC IRQ transform: 0000:00:1f.2[B] -> IRQ 153
    PCI->APIC IRQ transform: 0000:00:1f.3[B] -> IRQ 153
    PCI->APIC IRQ transform: 0000:04:00.0[A] -> IRQ 129
    PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 137
    Machine check exception polling timer started.
    highmem bounce pool size: 64 pages
    fuse init (API version 7.1)
    Initializing Cryptographic API
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    PCI: Setting latency timer of device 0000:00:1c.0 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    PCI: Setting latency timer of device 0000:00:1c.1 to 64
    assign_interrupt_mode Found MSI capability
    Allocate Port Service[pcie00]
    Allocate Port Service[pcie02]
    vesafb: framebuffer at 0xd8000000, mapped to 0xf8880000, using 5120k, total 131072k
    vesafb: mode is 1280x1024x16, linelength=2560, pages=1
    vesafb: protected mode interface info at c000:d620
    vesafb: scrolling: redraw
    vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
    Console: switching to colour frame buffer device 160x64
    fb0: VESA VGA frame buffer device
    fb1: Virtual frame buffer device, using 1024K of video memory
    Real Time Clock Driver v1.12
    i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
    i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
    cn_fork is registered
    cn_exit is registered
    mice: PS/2 mouse device common for all mice
    io scheduler noop registered
    io scheduler cfq registered
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
    loop: loaded (max 8 devices)
    ub: sizeof ub_scsi_cmd 68 ub_dev 2384 ub_lun 140
    usbcore: registered new driver ub
    sk98lin: Network Device Driver v8.23.1.3
    (C)Copyright 1999-2005 Marvell(R).
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    eth0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
    PrefPort:A RlmtMode:Check Link State
    netconsole: not configured, aborting
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH6: IDE controller at PCI slot 0000:00:1f.1
    ICH6: chipset revision 5
    ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
    Probing IDE interface ide0...
    hda: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
    hdb: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
    libata version 1.11 loaded.
    ata_piix version 1.03
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    ata1: SATA max UDMA/133 cmd 0xAC00 ctl 0xA882 bmdma 0xA400 irq 153
    ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA482 bmdma 0xA408 irq 153
    ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata1: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata1: dev 0 configured for UDMA/133
    scsi0 : ata_piix
    ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
    ata2: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
    ata2: dev 0 configured for UDMA/133
    scsi1 : ata_piix
    Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
    Type: Direct-Access ANSI SCSI revision: 05
    Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
    Type: Direct-Access ANSI SCSI revision: 05
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sda: drive cache: write back
    sda: sda1 sda2 < sda5 sda6 sda7 >
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
    SCSI device sdb: drive cache: write back
    sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 >
    Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
    Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
    Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
    usbmon: debugs is not available
    PCI: Setting latency timer of device 0000:00:1d.7 to 64
    ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
    ehci_hcd 0000:00:1d.7: debug port 1
    ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 01010001)
    ehci_hcd 0000:00:1d.7: continuing after BIOS bug...
    ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:1d.7: irq 161, io mem 0xd2dffc00
    PCI: cache line size of 32 is not supported by device 0000:00:1d.7
    ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 8 ports detected
    USB Universal Host Controller Interface driver v2.3
    PCI: Setting latency timer of device 0000:00:1d.0 to 64
    uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
    uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:1d.0: irq 161, io base 0x00009880
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.1 to 64
    uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
    uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:1d.1: irq 153, io base 0x00009c00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.2 to 64
    uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
    uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:1d.2: irq 145, io base 0x0000a000
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    PCI: Setting latency timer of device 0000:00:1d.3 to 64
    uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
    uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    uhci_hcd 0000:00:1d.3: irq 129, io base 0x0000a080
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 2 ports detected
    usbcore: registered new driver usblp
    drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
    Initializing USB Mass Storage driver...
    usb 2-1: new low speed USB device using uhci_hcd and address 2
    usb 2-2: new low speed USB device using uhci_hcd and address 3
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb 4-1: new full speed USB device using uhci_hcd and address 2
    input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
    input: USB HID v1.10 Mouse [Genius NetScroll+Mini Traveler] on usb-0000:00:1d.0-2
    usbcore: registered new driver usbhid
    drivers/usb/input/hid-core.c: v2.6:USB HID core driver
    md: linear personality registered as nr 1
    md: raid0 personality registered as nr 2
    md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
    md: bitmap version 3.38
    NET: Registered protocol family 2
    IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
    TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
    TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    TCP: Hash tables configured (established 262144 bind 65536)
    TCP reno registered
    TCP bic registered
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    Using IPI Shortcut mode
    md: Autodetecting RAID arrays.
    md: autorun ...
    md: considering sdb7 ...
    md: adding sdb7 ...
    md: sdb6 has different UUID to sdb7
    md: sdb5 has different UUID to sdb7
    md: sda7 has different UUID to sdb7
    md: adding sda6 ...
    md: sda5 has different UUID to sdb7
    md: created md2
    md: bind<sda6>
    md: bind<sdb7>
    md: running: <sdb7><sda6>
    md2: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb7
    raid0: comparing sdb7(20000768) with sdb7(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda6
    raid0: comparing sda6(20000768) with sdb7(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: considering sdb6 ...
    md: adding sdb6 ...
    md: sdb5 has different UUID to sdb6
    md: sda7 has different UUID to sdb6
    md: adding sda5 ...
    md: created md0
    md: bind<sda5>
    md: bind<sdb6>
    md: running: <sdb6><sda5>
    md0: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb6
    raid0: comparing sdb6(20000768) with sdb6(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda5
    raid0: comparing sda5(20000768) with sdb6(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: considering sdb5 ...
    md: adding sdb5 ...
    md: adding sda7 ...
    md: created md1
    md: bind<sda7>
    md: bind<sdb5>
    md: running: <sdb5><sda7>
    md1: setting max_sectors to 128, segment boundary to 32767
    raid0: looking at sdb5
    raid0: comparing sdb5(20000768) with sdb5(20000768)
    raid0: END
    raid0: ==> UNIQUE
    raid0: 1 zones
    raid0: looking at sda7
    raid0: comparing sda7(20000768) with sdb5(20000768)
    raid0: EQUAL
    raid0: FINAL 1 zones
    raid0: done.
    raid0 : md_size is 40001536 blocks.
    raid0 : conf->hash_spacing is 40001536 blocks.
    raid0 : nb_zone is 1.
    raid0 : Allocating 4 bytes for hash.
    md: ... autorun DONE.
    VFS: Mounted root (reiser4 filesystem) readonly.
    Freeing unused kernel memory: 168k freed
    ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
    ReiserFS: sdb1: using ordered data mode
    ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
    ReiserFS: sdb1: checking transaction log (sdb1)
    ReiserFS: sdb1: Using r5 hash to sort names
    eth0: network connection up using port A
    speed: 100
    autonegotiation: yes
    duplex mode: full
    flowctrl: symmetric
    irq moderation: disabled
    tcp offload: enabled
    scatter-gather: enabled
    tx-checksum: enabled
    rx-checksum: enabled
    rx-polling: enabled
    PCI: Setting latency timer of device 0000:00:1b.0 to 64
    hda_codec: Unknown model for ALC880, trying auto-probe from BIOS...
    Unable to handle kernel NULL pointer dereference at virtual address 00000000
    printing eip:
    f8f421d4
    *pde = 00000000
    Oops: 0002 [#1]
    PREEMPT
    last sysfs file:
    Modules linked in: snd_hda_intel snd_hda_codec snd_pcm snd_timer snd soundcore snd_page_alloc
    CPU: 0
    EIP: 0060:[<f8f421d4>] Not tainted VLI
    EFLAGS: 00010293 (2.6.13-rc3-mm1pm)
    eax: fffffffe ebx: f7bf6748 ecx: 00000000 edx: 00000000
    esi: f7bf6600 edi: 00000000 ebp: 00000006 esp: f718fde4
    ds: 007b es: 007b ss: 0068
    Process modprobe (pid: 6993, threadinfo=f718e000 task=f74d7a90)
    Stack: 00000000 00000000 00000000 00000000 f7bf6600 f7bf6748 f7689000 f8f42713
    f7bf6600 f7689000 f8f4298d f8f460d8 f8f45556 00000001 f8f3e77e 00000f00
    00000005 00000000 f7689000 f753b240 00000000 f8f3e984 00000f00 00000002
    Call Trace:
    [<f8f42713>]
    [<f8f4298d>]
    [<f8f3e77e>]
    [<f8f3e984>]
    [<f8f3e592>]
    [<c0254b3e>]
    [<f8851871>]
    [<f8851100>]
    [<f8851220>]
    [<f88524a3>]
    [<c02619ca>]
    [<c0261a06>]
    [<c0293273>]
    [<c02933a9>]
    [<c029292a>]
    [<c02933c6>]
    [<c0293370>]
    [<c0292e1c>]
    [<c0293795>]
    [<c0261c68>]
    [<c0135be9>]
    [<c0102c7b>]
    Code: 31 c0 53 83 ec 10 89 d3 89 e7 f3 ab 8b 12 31 ff 83 fa 00 7e 45 89 f6 0f b7 44 7b 04 8d 48 ec 66 83 f9 03 77 13 8b 56 3c 83 e8 16 <66> 89 04 7a 8b 13 c7 04 8c 01 00 00 00 47 39 fa 7f da 31 ff 83


    \
     
     \ /
      Last update: 2005-07-29 17:50    [W:0.134 / U:29.504 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site