lkml.org 
[lkml]   [2005]   [Jul]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: DriveStatusError BadCRC
    I run this command and I obtained:

    smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce
    Allen
    Home page is http://smartmontools.sourceforge.net/

    === START OF INFORMATION SECTION ===
    Device Model: Maxtor 6Y080L0
    Serial Number: Y23TZR2C
    Firmware Version: YAR41BW0
    User Capacity: 81,964,302,336 bytes
    Device is: In smartctl database [for details use: -P show]
    ATA Version is: 7
    ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
    Local Time is: Fri Jul 22 11:46:20 2005 CEST
    SMART support is: Available - device has SMART capability.
    SMART support is: Enabled

    === START OF READ SMART DATA SECTION ===
    SMART overall-health self-assessment test result: PASSED

    General SMART Values:
    Offline data collection status: (0x80) Offline data collection activity
    was never started.
    Auto Offline Data Collection: Enabled.
    Self-test execution status: ( 0) The previous self-test routine completed
    without error or no self-test has ever
    been run.
    Total time to complete Offline
    data collection: ( 241) seconds.
    Offline data collection
    capabilities: (0x5b) SMART execute Offline immediate.
    Auto Offline data collection on/off support.
    Suspend Offline collection upon new
    command.
    Offline surface scan supported.
    Self-test supported.
    No Conveyance Self-test supported.
    Selective Self-test supported.
    SMART capabilities: (0x0003) Saves SMART data before entering
    power-saving mode.
    Supports SMART auto save timer.
    Error logging capability: (0x01) Error logging supported.
    No General Purpose Logging support.
    Short self-test routine
    recommended polling time: ( 2) minutes.
    Extended self-test routine
    recommended polling time: ( 37) minutes.

    SMART Attributes Data Structure revision number: 16
    Vendor Specific SMART Attributes with Thresholds:
    ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
    WHEN_FAILED RAW_VALUE
    3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always
    - 323
    4 Start_Stop_Count 0x0032 253 253 000 Old_age Always
    - 3
    5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always
    - 1
    6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline
    - 0
    7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always
    - 0
    8 Seek_Time_Performance 0x0027 251 245 187 Pre-fail Always
    - 37971
    9 Power_On_Minutes 0x0032 253 253 000 Old_age Always
    - 95h+25m
    10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always
    - 0
    11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always
    - 0
    12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always
    - 9
    192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
    - 0
    193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
    - 0
    194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
    - 38
    195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
    - 949
    196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline
    - 0
    197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline
    - 0
    198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline
    - 0
    199 UDMA_CRC_Error_Count 0x0008 183 174 000 Old_age Offline
    - 30
    200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
    - 0
    201 Soft_Read_Error_Rate 0x000a 253 233 000 Old_age Always
    - 75
    202 TA_Increase_Count 0x000a 253 252 000 Old_age Always
    - 0
    203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
    - 0
    204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always
    - 0
    205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
    - 0
    207 Spin_High_Current 0x002a 252 252 000 Old_age Always
    - 0
    208 Spin_Buzz 0x002a 252 252 000 Old_age Always
    - 0
    209 Offline_Seek_Performnce 0x0024 196 196 000 Old_age Offline
    - 0
    99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
    - 0
    100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
    - 0
    101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
    - 0

    SMART Error Log Version: 1
    Warning: ATA error count 46 inconsistent with error log pointer 5

    ATA Error Count: 46 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
    Powered_Up_Time is measured from power on, and printed as
    DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
    SS=sec, and sss=millisec. It "wraps" after 49.710 days.

    Error 46 occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
    When the command that caused the error occurred, the device was in an unknown
    state.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 c1 80 c9 2c e3 Error: ICRC, ABRT at LBA = 0x032cc980 = 53266816

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    ca 00 00 41 c9 2c e3 08 00:37:40.848 WRITE DMA
    ca 00 00 41 c8 2c e3 08 00:37:40.832 WRITE DMA
    ca 00 08 29 39 43 e3 08 00:37:40.832 WRITE DMA
    ca 00 08 d9 33 43 e3 08 00:37:40.832 WRITE DMA
    ca 00 08 c9 33 43 e3 08 00:37:40.832 WRITE DMA

    Error 45 occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
    When the command that caused the error occurred, the device was in an unknown
    state.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 00 39 8d 2c e3 Error: ICRC, ABRT at LBA = 0x032c8d39 = 53251385

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    ca 00 00 39 8d 2c e3 08 00:33:07.648 WRITE DMA
    ca 00 00 39 8c 2c e3 08 00:33:07.648 WRITE DMA
    c8 00 80 80 30 c9 e6 08 00:33:07.632 READ DMA
    ca 00 18 89 bf 40 e3 08 00:33:07.632 WRITE DMA
    ca 00 60 21 bf 40 e3 08 00:33:07.632 WRITE DMA

    Error 44 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
    When the command that caused the error occurred, the device was in an unknown
    state.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    ca 00 b8 39 b9 2c e3 08 2d+06:26:20.352 WRITE DMA
    ca 00 b8 39 b9 2c e3 08 2d+06:26:20.288 WRITE DMA
    10 00 ff 00 00 00 e0 08 2d+06:26:20.272 RECALIBRATE [OBS-4]
    ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA
    ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA

    Error 43 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
    When the command that caused the error occurred, the device was in an unknown
    state.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    ca 00 b8 39 b9 2c e3 08 2d+06:26:20.288 WRITE DMA
    10 00 ff 00 00 00 e0 08 2d+06:26:20.272 RECALIBRATE [OBS-4]
    ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA
    ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA
    ca 00 10 81 a6 31 e3 08 2d+06:26:19.952 WRITE DMA

    Error 42 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
    When the command that caused the error occurred, the device was in an unknown
    state.

    After command completion occurred, registers were:
    ER ST SC SN CL CH DH
    -- -- -- -- -- -- --
    84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713

    Commands leading to the command that caused the error were:
    CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    -- -- -- -- -- -- -- -- ---------------- --------------------
    ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA
    ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA
    ca 00 10 81 a6 31 e3 08 2d+06:26:19.952 WRITE DMA
    ca 00 08 91 a5 31 e3 08 2d+06:26:19.952 WRITE DMA
    ca 00 10 b1 a3 31 e3 08 2d+06:26:19.952 WRITE DMA

    SMART Self-test log structure revision number 1
    No self-tests have been logged. [To run self-tests, use: smartctl -t]


    SMART Selective self-test log data structure revision number 1
    SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
    1 0 0 Not_testing
    2 0 0 Not_testing
    3 0 0 Not_testing
    4 0 0 Not_testing
    5 0 0 Not_testing
    Selective self-test flags (0x0):
    After scanning selected spans, do NOT read-scan remainder of disk.
    If Selective self-test is pending on power-up, resume after 0 minute delay.


    thanks


    >-- Messaggio Originale --
    >Date: Fri, 22 Jul 2005 11:34:55 +0200 (MEST)
    >From: Jan Engelhardt <jengelh@linux01.gwdg.de>
    >To: sampei02@tiscali.it
    >cc: linux-kernel@vger.kernel.org
    >Subject: Re: DriveStatusError BadCRC
    >
    >
    >>I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving
    this
    >>message:
    >>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
    >>hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
    >>ide: failed opcode was: unknown
    >>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
    >>hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
    >>ide: failed opcode was: unknown
    >
    >Does this happen on boot?
    >
    >Check your harddrive... smartctl -data -a /dev/hda and look for
    >199 UDMA_CRC_Error_Count 0x0008 198 193 000 Old_age Offline
    > -
    >and
    > Commands leading to the command that caused the error were:
    > CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
    > -- -- -- -- -- -- -- -- ---------------- --------------------
    > c8 00 38 2f 8f 07 e4 08 43d+13:12:02.304 READ DMA
    >
    >
    >
    >Jan Engelhardt
    >--
    >-
    >To unsubscribe from this list: send the line "unsubscribe linux-kernel"
    in
    >the body of a message to majordomo@vger.kernel.org
    >More majordomo info at http://vger.kernel.org/majordomo-info.html
    >Please read the FAQ at http://www.tux.org/lkml/


    __________________________________________________________________
    TISCALI ADSL 1.25 MEGA
    Solo con Tiscali Adsl navighi senza limiti e telefoni senza canone Telecom
    a partire da 19,95 Euro/mese.
    Attivala entro il 28 luglio, il primo MESE è GRATIS! CLICCA QUI.
    http://abbonati.tiscali.it/adsl/sa/1e25flat_tc/



    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-07-22 11:53    [W:0.043 / U:29.988 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site