Messages in this thread | | | Date | Thu, 23 Jun 2005 09:50:04 +0200 | From | Pierre Ossman <> | Subject | Re: 2.6.12 breaks 8139cp |
| |
Bjorn Helgaas wrote:
>On Wednesday 22 June 2005 3:03 pm, Pierre Ossman wrote: > > >>Upgrading from 2.6.11 to 2.6.12 caused my 8139cp network card to stop >>working. No error messages are emitted and everything seems to work >>(from the local computers point of view). But nothing can be recieved >>from the network. >> >> > >You might post a little more information (i.e., the 2.6.12 dmesg and >possibly a diff vs. 2.6.11). My guess is something's busted with its >IRQ. > >
dmesg:s included. But they don't really differ more than some cosmetic changes in the output strings.
The problem is I can't find anything that differs. 2.6.12 behaves more or less like someone cut of the rx pins in the connector. ifconfig doesn't report any errors so it isn't a problem with packets getting dropped. tcpdump only shows the outgoing packets.
Any more ideas on what I should examine to find any differences?
Rgds Pierre
000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable) BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved) BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS) BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131024 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126928 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 COMPAQ ) @ 0x000f6560 ACPI: RSDT (v001 HP CPQ0860 0x13090420 CPQ 0x00000001) @ 0x1fff0c84 ACPI: FADT (v002 HP CPQ0860 0x00000002 CPQ 0x00000001) @ 0x1fff0c00 ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1fff5c3c ACPI: DSDT (v001 HP nx7000 0x00010000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 Allocating PCI resources starting at 20000000 (gap: 20000000:e0000000) Built 1 zonelists Kernel command line: ro root=/dev/hda5 rhgb quiet Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01404000) Initializing CPU#0 CPU 0 irqstacks, hard=c0541000 soft=c0540000 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1594.918 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 512904k/524096k available (3371k kernel code, 10588k reserved, 732k data, 220k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3162.11 BogoMIPS (lpj=1581056) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) M processor 1600MHz stepping 05 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: setting ELCR to 0200 (from 0c20) checking if image is initramfs... it is Freeing initrd memory: 1090k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050211 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [C046] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Via IRQ fixup PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT] ACPI: Embedded Controller [C0EA] (gpe 28) ACPI: Power Resource [C18D] (on) ACPI: Power Resource [C195] (on) ACPI: Power Resource [C19C] (on) ACPI: Power Resource [C1A6] (on) ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10) ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10) ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10) ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10) ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled. ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11 ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled. ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ** PCI interrupts are no longer routed automatically. If this ** causes a device to stop working, it is probably because the ** driver failed to call pci_enable_device(). As a temporary ** workaround, the "pci=routeirq" argument restores the old ** behavior. If this argument makes the device work again, ** please email the output of "lspci" to bjorn.helgaas@hp.com ** so I can fix the driver. pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:00' and the driver 'system' pnp: match found with the PnP device '00:0c' and the driver 'system' pnp: match found with the PnP device '00:0d' and the driver 'system' pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved pnp: 00:0d: ioport range 0x1100-0x113f has been reserved pnp: 00:0d: ioport range 0x1200-0x121f has been reserved pnp: match found with the PnP device '00:0e' and the driver 'system' apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1119514693.293:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SGI XFS with ACLs, security attributes, no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 855PM Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 256M @ 0xb0000000 [drm] Initialized drm 1.0.0 20040925 ACPI: PS/2 Keyboard Controller [C1A3] at I/O 0x60, 0x64, irq 1 ACPI: PS/2 Mouse Controller [C1A4] at irq 12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A pnp: the driver 'serial' has been registered pnp: match found with the PnP device '00:03' and the driver 'serial' ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x4c40-0x4c47, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x4c48-0x4c4f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: TOSHIBA MK4025GAS, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 pnp: the driver 'ide' has been registered ide2: I/O resource 0x3EE-0x3EE not free. ide2: ports already in use, skipping probe Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 128KiB hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 > hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 Synaptics Touchpad, model: 1 Firmware: 5.9 Sensor: 35 new absolute packet format Touchpad has extended capability bits -> multifinger detection -> palm detection input: SynPS/2 Synaptics TouchPad on isa0060/serio4 NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 32Kbytes TCP established hash table entries: 32768 (order: 6, 262144 bytes) TCP bind hash table entries: 32768 (order: 7, 917504 bytes) TCP: Hash tables configured (established 32768 bind 32768) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Software Suspend Core. Software Suspend text mode support loaded. Software Suspend LZF Compression Driver registered. Software Suspend Swap Writer registered. ACPI wakeup devices: C058 C1AD C1A3 C1A4 C0AC C0B3 C0B4 C0B5 C0E7 C136 ACPI: (supports S0 S3 S4 S4bios S5) Freeing unused kernel memory: 220k freed Looking for first block of swap header at block 0. Setting logical block size of resume device to 4096. Software Suspend 2.1.8: Swap space signature found. Software Suspend 2.1.8: Suspending enabled. Software Suspend 2.1.8: This is normal swap space. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 10 (level, low) -> IRQ 10 eth0: RTL-8139C+ at 0xe0828000, 00:02:3f:22:db:8c, IRQ 10 ieee80211_crypt: registered algorithm 'NULL' ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.4 ipw2200: Copyright(c) 2003-2004 Intel Corporation ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5 ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 5 (level, low) -> IRQ 5 ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection ipw2200: Radio Frequency Kill Switch is On: Kill switch must be turned off for wireless networking to work. ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 49284 usecs intel8x0: clocking to 48000 ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 hw_random: RNG not detected ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 5 (level, low) -> IRQ 5 ehci_hcd 0000:00:1d.7: EHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 5, pci mem 0xa0000000 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v2.2 ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:1d.0: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 10, io base 0x48c0 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:1d.1: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 5, io base 0x48e0 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:1d.2: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 5, io base 0x4c00 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Linux Kernel Card Services options: [pci] [cardbus] [pm] ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 5 (level, low) -> IRQ 5 Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44 Yenta: ISA IRQ mask 0x0000, PCI irq 5 Socket status: 30000006 ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org> ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 10 (level, low) -> IRQ 10 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[90200000-902007ff] Max Packet=[1024] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f454a000284] ACPI: AC Adapter [C134] (on-line) ACPI: Battery Slot [C11F] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [C136] ibm_acpi: ec object not found ACPI: Video Device [C0D0] (multi-head: yes rom: no post: no) EXT3 FS on hda5, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 977248k swap on /dev/hda2. Priority:-1 extents:1 ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4094 buckets, 32752 max) - 244 bytes per conntrack cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0x800-0x8ff: clean. cs: IO port probe 0x100-0x4ff: excluding 0x140-0x14f 0x200-0x20f 0x378-0x37f cs: IO port probe 0xa00-0xaff: clean. Bluetooth: Core ver 2.7 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.7 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM ver 1.5 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.1 NET: Registered protocol family 23 IrCOMM protocol (Dag Brattli) CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 IrDA: Registered device irda0 (irport io=0x3E8 irq=3) drivers/net/irda/irport.c:442: spin_is_locked(drivers/net/irda/irport.c:db025608) already locked by drivers/net/irda/irport.c/912 drivers/net/irda/irport.c:443: spin_lock(drivers/net/irda/irport.c:db025608) already locked by drivers/net/irda/irport.c/912 drivers/net/irda/irport.c:919: spin_unlock(drivers/net/irda/irport.c:db025608) not locked pnp: the driver 'parport_pc' has been registered pnp: match found with the PnP device '00:05' and the driver 'parport_pc' parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] lp0: using parport0 (interrupt-driven). lp0: console ready tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10 [drm] Initialized radeon 1.14.0 20050125 on minor 0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 ipw2200: failed to send SYSTEM_CONFIG command ipw2200: ipw_send_system_config failed Linux version 2.6.12 (root@poseidon.drzeus.cx) (gcc version 4.0.0 20050616 (Red Hat 4.0.0-12)) #3 Wed Jun 22 21:10:33 CEST 2005 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable) BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved) BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS) BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved) 511MB LOWMEM available. On node 0 totalpages: 131024 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126928 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 COMPAQ ) @ 0x000f6560 ACPI: RSDT (v001 HP CPQ0860 0x13090420 CPQ 0x00000001) @ 0x1fff0c84 ACPI: FADT (v002 HP CPQ0860 0x00000002 CPQ 0x00000001) @ 0x1fff0c00 ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1fff5c3c ACPI: DSDT (v001 HP nx7000 0x00010000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 Allocating PCI resources starting at 20000000 (gap: 20000000:e0000000) Built 1 zonelists Kernel command line: ro root=/dev/hda5 rhgb quiet Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01404000) Initializing CPU#0 CPU 0 irqstacks, hard=c0542000 soft=c0541000 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 1594.880 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 512892k/524096k available (3386k kernel code, 10600k reserved, 725k data, 216k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 3162.11 BogoMIPS (lpj=1581056) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel(R) Pentium(R) M processor 1600MHz stepping 05 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. ACPI: setting ELCR to 0200 (from 0c20) checking if image is initramfs... it is Freeing initrd memory: 1090k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050309 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [C046] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT] ACPI: Embedded Controller [C0EA] (gpe 28) ACPI: Power Resource [C18D] (on) ACPI: Power Resource [C195] (on) ACPI: Power Resource [C19C] (on) ACPI: Power Resource [C1A6] (on) ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10) ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10) ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10) ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10) ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled. ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11 ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled. ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:00' and the driver 'system' pnp: match found with the PnP device '00:0c' and the driver 'system' pnp: match found with the PnP device '00:0d' and the driver 'system' pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved pnp: 00:0d: ioport range 0x1100-0x113f has been reserved pnp: 00:0d: ioport range 0x1200-0x121f has been reserved pnp: match found with the PnP device '00:0e' and the driver 'system' audit: initializing netlink socket (disabled) audit(1119514452.486:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SGI XFS with ACLs, security attributes, no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 855PM Chipset. agpgart: AGP aperture is 256M @ 0xb0000000 [drm] Initialized drm 1.0.0 20040925 pnp: the driver 'i8042 kbd' has been registered pnp: match found with the PnP device '00:0a' and the driver 'i8042 kbd' pnp: the driver 'i8042 aux' has been registered pnp: match found with the PnP device '00:0b' and the driver 'i8042 aux' PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A pnp: the driver 'serial' has been registered pnp: match found with the PnP device '00:03' and the driver 'serial' ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x4c40-0x4c47, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x4c48-0x4c4f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: TOSHIBA MK4025GAS, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 pnp: the driver 'ide' has been registered ide2: I/O resource 0x3EE-0x3EE not free. ide2: ports already in use, skipping probe Probing IDE interface ide3... Probing IDE interface ide4... Probing IDE interface ide5... hda: max request size: 128KiB hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 > hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide usbmon: debugs is not available usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 32Kbytes TCP established hash table entries: 32768 (order: 6, 262144 bytes) TCP bind hash table entries: 32768 (order: 7, 917504 bytes) TCP: Hash tables configured (established 32768 bind 32768) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Software Suspend Core. Software Suspend Compression Driver loading. Software Suspend Encryption Driver loading. Software Suspend text mode support loading. Software Suspend userspace UI support loading. Software Suspend Swap Writer loading. ACPI wakeup devices: C058 C1AD C1A3 C1A4 C0AC C0B3 C0B4 C0B5 C0E7 C136 ACPI: (supports S0 S3 S4 S4bios S5) Freeing unused kernel memory: 216k freed Software Suspend 2.1.9.5: Swapwriter: Signature found. Software Suspend 2.1.9.5: Suspending enabled. input: AT Translated Set 2 keyboard on isa0060/serio0 EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008 input: SynPS/2 Synaptics TouchPad on isa0060/serio4 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10 eth0: RTL-8139C+ at 0xe0828000, 00:02:3f:22:db:8c, IRQ 10 ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 49076 usecs intel8x0: clocking to 48000 ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 hw_random: RNG not detected ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5 ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v2.2 ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5 ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Linux Kernel Card Services options: [pci] [cardbus] [pm] ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low) -> IRQ 5 Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44 Yenta: ISA IRQ mask 0x0000, PCI irq 5 Socket status: 30000006 ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org> ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[90200000-902007ff] Max Packet=[1024] ACPI: AC Adapter [C134] (on-line) ACPI: Battery Slot [C11F] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [C136] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Video Device [C0D0] (multi-head: yes rom: no post: no) EXT3 FS on hda5, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 977248k swap on /dev/hda2. Priority:-1 extents:1 ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4094 buckets, 32752 max) - 240 bytes per conntrack cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0x800-0x8ff: clean. cs: IO port probe 0x100-0x4ff: excluding 0x140-0x14f 0x200-0x20f 0x378-0x37f cs: IO port probe 0xa00-0xaff: clean. Bluetooth: Core ver 2.7 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.7 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM ver 1.5 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.1 NET: Registered protocol family 23 IrCOMM protocol (Dag Brattli) CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 IrDA: Registered device irda0 (irport io=0x3E8 irq=3) drivers/net/irda/irport.c:406: spin_is_locked(drivers/net/irda/irport.c:db38c548) already locked by drivers/net/irda/irport.c/878 drivers/net/irda/irport.c:407: spin_lock(drivers/net/irda/irport.c:db38c548) already locked by drivers/net/irda/irport.c/878 drivers/net/irda/irport.c:885: spin_unlock(drivers/net/irda/irport.c:db38c548) not locked pnp: the driver 'parport_pc' has been registered pnp: match found with the PnP device '00:05' and the driver 'parport_pc' parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] lp0: using parport0 (interrupt-driven). lp0: console ready tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI 10 (level, low) -> IRQ 10 [drm] Initialized radeon 1.16.0 20050311 on minor 0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
| |