lkml.org 
[lkml]   [2005]   [Jun]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject2.6.12-rc6-mm1 oops on startup.
Hi,

I have used the kernel.org normal kernel, and it compiles and boots fine.
I then use exactly the same .config file for the 2.6.12-rc6-mm1 and it
fails to boot.

I attach the oops.txt that I captures via the serial port.

Can anybody help, because I wish to test the PCMCIA code.

Thank you

James
Linux version 2.6.12-rc6-mm1 (root@new) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.
4.4-1.0, pie-8.7.8)) #1 SMP Sat Jun 18 17:07:03 BST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI d
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5d50
DMI 2.2 present.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Initializing CPU#0
Kernel command line: root=/dev/hdd5 console=tty0 console=ttyS0,9600 nmi_watchdog
=1
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2806.614 MHz processor.
Using tsc for high-res t
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1033612k/1048512k available (2522k kernel code, 14064k reserved, 948k da
ta, 208k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5620.79 BogoMIPS (lpj=11241599)

Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table en
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5613.20 BogoMIPS (lpj=11226408)

CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11234.00 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
softlockup thread 0 started up.
Brought up 2 CPUs
softlockup thread 1 started up.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfba10, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Unable to handle kernel paging request at virtual address f7f29b8c
printing eip:
c011f704
*pde = 00538067
Oops: 0000 [#1]
PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0
EIP: 0060:[<c011f704>] Not tainted VLI
EFLAGS: 00010286 (2.6.12-rc6-mm1)
EIP is at do_fork+0xd4/0x20e
eax: c1a76000 ebx: f7f29af0 ecx: c1a77e30 edx: c19a6af0
esi: 00004000 edi: 00000051 ebp: c1a77eb4 esp: c1a77e58
ds: 007b es: 007b ss: 0068
Process khelper (pid: 10, threadinfo=c1a76000 task=c19a6af0)
Stack: 00804111 00000000 c1a77ed4 00000000 00000000 00000000 00000051 00000000
00000001 dead4ead 00000000 00000069 00000000 00000001 dead4ead 00000000
c1a77e98 c1a77e98 c1811e80 c1811520 c19bbe4c c19a5df8 00000000 c1a77f18
Call Trace:
[<c01040df>] show_stack+0x7f/0xa0
[<c0104284>] show_registers+0x164/0x1e0
[<c01044cd>] die+0x10d/0x1a0
[<c011731c>] do_page_fault+0x4bc/0x6b8
[<c0103d0f>] error_code+0x4f/0x54
[<c01012a9>] kernel_thread+0x79/0x80
[<c0131de9>] __call_usermodehelper+0x59/0x70
[<c01322b5>] worker_thread+0x1d5/0x260
[<c0136e4d>] kthread+0xad/0xf0
[<c0101225>] kernel_thread_helper+0x5/0x10
Code: 84 b5 00 00 00 c7 03 04 00 00 00 8b 45 c0 85 c0 0f 85 0f 01 00 00 81 e6 00
40 00 00 0f 85 a6 00 00 00 b8 00 e0 ff ff 21 e0 8b 10 <8b> 83 9c 00 00 00 89 44
24 0c 8b 83 a0 00 00 00 89 44 24 08 8b
\
 
 \ /
  Last update: 2005-06-18 20:53    [W:0.488 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site