lkml.org 
[lkml]   [2005]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectDMA not works in Linux 2.6.12, but in Windows works fine.
Date
Problem descrition:

DMA not works in Linux 2.6.12, but in Windows works fine.

DMA not works with HDD and CD drives connected by 80-conductor
cable to secondary IDE port (ide1).


Hardware description:

1) Motherboard has chipset Intel, Giga-byte
2) HDD Seagate ST3160023AS (Serial ATA)
3) HDD Seagate ST3200822A (IDE ATA)
4) SONY CD-RW CRX320E, IDE ATAPI CD/DVD-ROM


Hardware connections:

ST3160023AS ---> SATA0 ---> BIOS mapping ---> ide0 Pri master
(hda)
SATA1 ---> BIOS mapping ---> ide0 Pri slave
CRX320E --------------------------------> ide1 Sec master
(hdc)
ST3200822A --------------------------------> ide1 Sec slave
(hdd)


==============================================================================
=== hdparm output
============================================================

# hdparm -V
hdparm v5.5

# hdparm -d1 /dev/hdd
/dev/hdd:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)

# hdparm -d1 /dev/hdc
/dev/hdd:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)

# hdparm -I /dev/hdd

/dev/hdd:

ATA device, with non-removable media
Model Number: ST3200822A
Serial Number: 5LJ1JK9L
Firmware Revision: 3.01
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 2
Supported: 6 5 4 3
Configuration:
Logical max current
cylinders 16383 65535
heads 16 1
sectors/track 63 63
--
CHS current addressable sectors: 4128705
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 390721968
device size with M = 1024*1024: 190782 MBytes
device size with M = 1000*1000: 200049 MBytes (200 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific
minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow
control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 1 determined by CSEL
Checksum: correct


==============================================================================
=== some lines from .config
==================================================

CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set

CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y


==============================================================================
=== Some lines from `lspci -v` output
========================================

0000:00:00.0 Host bridge: Intel Corp. 82865G/PE/P Processor to I/O
Controller (rev 02)
Subsystem: Giga-byte Technology: Unknown device 2570
Flags: bus master, fast devsel, latency 0
Memory at e0000000 (32-bit, prefetchable)
Capabilities: [e4] #09 [1106]

0000:00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev
c2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f8000000-f80fffff

0000:00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller
(rev 02)
Flags: bus master, medium devsel, latency 0

0000:00:1f.2 IDE interface: Intel Corp. 82801EB Ultra ATA Storage
Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology: Unknown device 24d1
Flags: bus master, 66Mhz, medium devsel, latency 0, IRQ 18
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at f000 [size=16]

0000:00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02)
Subsystem: Giga-byte Technology: Unknown device 24d2
Flags: medium devsel, IRQ 9
I/O ports at 1400 [size=32]


==============================================================================
=== Some lines of kernel-bool messages
=======================================

Linux version 2.6.12-rc2 (root@wcm-5) (gcc version 3.3.3 (SuSE Linux))
#1 SMP Mon May 23 11:05:23 EEST 2005
Kernel command line: BOOT_IMAGE=Linux-2.6.12 ro root=806
resume=/dev/sda5 ide1=dma
ide_setup: ide1=dma -- OBSOLETE OPTION, WILL BE REMOVED SOON!
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: SONY CD-RW CRX320E, ATAPI CD/DVD-ROM drive
hdd: ST3200822A, ATA DISK drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide1 at 0x170-0x177,0x376 on irq 15
hdd: max request size: 1024KiB
hdd: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hdd: cache flushes supported
hdd: hdd1 hdd2
hdc: ATAPI 52X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.10 loaded.
ata_piix version 1.03
ata_piix: combined mode detected
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01
87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 312579695 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
Vendor: ATA Model: ST3160023AS Rev: 3.00
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312579695 512-byte hdwr sectors (160041 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 > sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0


==============================================================================
==============================================================================


Please, help!


p.s. I am not in mailing-list, so please add me to CC.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-05-23 12:29    [W:0.067 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site