Messages in this thread | | | Subject | Re: EDD Support | From | Henry Molina <> | Date | Mon, 09 Aug 2004 15:10:52 -0500 |
| |
Ok Patrick, but /sys/firmware is not created.
I using now module-init-tools 3.00-pre10
modprobe -v -s edd insmod /lib/modules/2.6.5-1.358/kernel/drivers/firmware/edd.ko
and /proc/kmsg shows: <6>BIOS EDD facility v0.15 2004-May-17, 1 devices found
On Mon, 2004-08-09 at 12:44, Henry Molina wrote: > No Randy, no messages, I'm using insmod from BusyBox v1.00-pre10, and > lsmod shows the module ok. > > On Mon, 2004-08-09 at 11:35, Randy.Dunlap wrote: > > On Mon, 09 Aug 2004 11:43:31 -0500 Henry Molina wrote: > > > > | Hi everyone, > > > > Hi Henry, > > > > | I'm compiling kernel 2.6.7 with CONFIG_EDD fine, then I proceed to > > | install the module but I can't get the /proc/sys/firmware/edd entry. > > | > > | Any Suggestion?. > > > > Any kernel log messages when you load the module? > > Hint: there should be. > > > > | Many Thanks, > > | > > | Henry Molina > > | > > | PD: I attach the dmidecode output > > | > > | # dmidecode 2.2 > > | SMBIOS 2.3 present. > > | 31 structures occupying 1017 bytes. > > | Table at 0x000F0630. > > | Handle 0x0000 > > | DMI type 0, 20 bytes. > > | BIOS Information > > | Vendor: American Megatrends Inc. > > | Version: 1.02 > > | Release Date: 05/09/2003 > > | Address: 0xF0000 > > | Runtime Size: 64 kB > > | ROM Size: 512 kB > > | Characteristics: > > | ISA is supported > > | PCI is supported > > | PNP is supported > > | APM is supported > > | BIOS is upgradeable > > | BIOS shadowing is allowed > > | ESCD support is available > > | Boot from CD is supported > > | Selectable boot is supported > > | BIOS ROM is socketed > > | EDD is supported > > | 5.25"/360 KB floppy services are supported (int 13h) > > | 5.25"/1.2 MB floppy services are supported (int 13h) > > | 3.5"/720 KB floppy services are supported (int 13h) > > | 3.5"/2.88 MB floppy services are supported (int 13h) > > | Print screen service is supported (int 5h) > > | 8042 keyboard services are supported (int 9h) > > | Printer services are supported (int 17h) > > | CGA/mono video services are supported (int 10h) > > | ACPI is supported > > | USB legacy is supported > > | AGP is supported > > | LS-120 boot is supported > > | ATAPI Zip drive boot is supported > > | BIOS boot specification is supported > > | Handle 0x0001 > > | DMI type 1, 25 bytes. > > | System Information > > | Manufacturer: Hewlett-Packard > > | Product Name: HP d220 MT (DC526A) > > | Version: > > | Serial Number: MXD33701GQ > > | UUID: 15F4C490-59EA-D711-851C-517B4801761B > > | Wake-up Type: Power Switch > > | Handle 0x0002 > > | DMI type 2, 8 bytes. > > | Base Board Information > > | Manufacturer: Lite-On Tech. > > | Product Name: 0888h > > | Version: > > | Serial Number: 01234567 > > | Handle 0x0003 > > | DMI type 3, 17 bytes. > > | Chassis Information > > | Manufacturer: Hewlett-Packard > > | Type: Desktop > > | Lock: Not Present > > | Version: > > | Serial Number: > > | Asset Tag: > > | Boot-up State: Safe > > | Power Supply State: Safe > > | Thermal State: Safe > > | Security Status: None > > | OEM Information: 0x00000000 > > | Handle 0x0004 > > | DMI type 4, 32 bytes. > > | Processor Information > > | Socket Designation: mPGA-478 > > | Type: Central Processor > > | Family: Pentium 4 > > | Manufacturer: Intel > > | ID: 29 0F 41 33 FF FB EB BF > > | Signature: Type 0, Family 34F, Model 12, Stepping 9 > > | Flags: > > | FPU (Floating-point unit on-chip) > > | VME (Virtual mode extension) > > | DE (Debugging extension) > > | PSE (Page size extension) > > | TSC (Time stamp counter) > > | MSR (Model specific registers) > > | PAE (Physical address extension) > > | MCE (Machine check exception) > > | CX8 (CMPXCHG8 instruction supported) > > | APIC (On-chip APIC hardware supported) > > | SEP (Fast system call) > > | MTRR (Memory type range registers) > > | PGE (Page global enable) > > | MCA (Machine check architecture) > > | CMOV (Conditional move instruction supported) > > | PAT (Page attribute table) > > | PSE-36 (36-bit page size extension) > > | CLFSH (CLFLUSH instruction supported) > > | DS (Debug store) > > | ACPI (ACPI supported) > > | MMX (MMX technology supported) > > | FXSR (Fast floating-point save and restore) > > | SSE (Streaming SIMD extensions) > > | SSE2 (Streaming SIMD extensions 2) > > | SS (Self-snoop) > > | HTT (Hyper-threading technology) > > | TM (Thermal monitor supported) > > | SBF (Signal break on FERR) > > | Version: PENTIUM 4 > > | Voltage: 2.9 V > > | External Clock: 133 MHz > > | Max Speed: 4000 MHz > > | Current Speed: 2400 MHz > > | Status: Populated, Enabled > > | Upgrade: ZIF Socket > > | L1 Cache Handle: 0x0005 > > | L2 Cache Handle: 0x0006 > > | L3 Cache Handle: Not Provided > > | Handle 0x0005 > > | DMI type 7, 19 bytes. > > | Cache Information > > | Socket Designation: Internal Cache > > | Configuration: Enabled, Not Socketed, Level 1 > > | Operational Mode: Write Back > > | Location: Internal > > | Installed Size: 8 KB > > | Maximum Size: 1024 KB > > | Supported SRAM Types: > > | Synchronous > > | Installed SRAM Type: Pipeline Burst Synchronous > > | Speed: 40 ns > > | Error Correction Type: Single-bit ECC > > | System Type: Data > > | Associativity: 4-way Set-associative > > | Handle 0x0006 > > | DMI type 7, 19 bytes. > > | Cache Information > > | Socket Designation: Internal Cache > > | Configuration: Enabled, Not Socketed, Level 2 > > | Operational Mode: Write Back > > | Location: Internal > > | Installed Size: 512 KB > > | Maximum Size: 1024 KB > > | Supported SRAM Types: > > | Synchronous > > | Installed SRAM Type: Synchronous > > | Speed: 40 ns > > | Error Correction Type: Parity > > | System Type: Unified > > | Associativity: 8-way Set-associative > > | Handle 0x0007 > > | DMI type 5, 20 bytes. > > | Memory Controller Information > > | Error Detecting Method: None > > | Error Correcting Capabilities: None > > | Supported Interleave: One-way Interleave > > | Current Interleave: One-way Interleave > > | Maximum Memory Module Size: 1024 MB > > | Maximum Total Memory Size: 2048 MB > > | Supported Speeds: > > | Other > > | Supported Memory Types: > > | DIMM > > | SDRAM > > | Memory Module Voltage: 3.3 V > > | Associated Memory Slots: 2 > > | 0x0008 > > | 0x0009 > > | Enabled Error Correcting Capabilities: None > > | Handle 0x0008 > > | DMI type 6, 12 bytes. > > | Memory Module Information > > | Socket Designation: DIMM1 > > | Bank Connections: 1 0 > > | Current Speed: Unknown > > | Type: DIMM SDRAM > > | Installed Size: 128 MB (Single-bank Connection) > > | Enabled Size: 128 MB (Single-bank Connection) > > | Error Status: OK > > | Handle 0x0009 > > | DMI type 6, 12 bytes. > > | Memory Module Information > > | Socket Designation: DIMM2 > > | Bank Connections: 3 2 > > | Current Speed: Unknown > > | Type: Unknown > > | Installed Size: Not Installed (Single-bank Connection) > > | Enabled Size: Not Installed (Single-bank Connection) > > | Error Status: OK > > | Handle 0x000A > > | DMI type 9, 13 bytes. > > | System Slot Information > > | Designation: PCI1 > > | Type: 32-bit PCI > > | Current Usage: Available > > | Length: Long > > | ID: 1 > > | Characteristics: > > | 3.3 V is provided > > | Opening is shared > > | PME signal is supported > > | Handle 0x000B > > | DMI type 9, 13 bytes. > > | System Slot Information > > | Designation: PCI2 > > | Type: 32-bit PCI > > | Current Usage: Available > > | Length: Long > > | ID: 2 > > | Characteristics: > > | 3.3 V is provided > > | Opening is shared > > | PME signal is supported > > | Handle 0x000C > > | DMI type 9, 13 bytes. > > | System Slot Information > > | Designation: PCI3 > > | Type: 32-bit PCI > > | Current Usage: Available > > | Length: Long > > | ID: 3 > > | Characteristics: > > | 3.3 V is provided > > | Opening is shared > > | PME signal is supported > > | Handle 0x000D > > | DMI type 9, 13 bytes. > > | System Slot Information > > | Designation: AGP > > | Type: 32-bit PCI > > | Current Usage: Available > > | Length: Long > > | ID: 1 > > | Characteristics: > > | 3.3 V is provided > > | Opening is shared > > | PME signal is supported > > | Handle 0x000E > > | DMI type 11, 5 bytes. > > | OEM Strings > > | String 1: SMBIOS Support from AMI > > | Handle 0x000F > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: USB0 > > | Internal Connector Type: None > > | External Reference Designator: USB1 > > | External Connector Type: Access Bus (USB) > > | Port Type: USB > > | Handle 0x0010 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: USB1 > > | Internal Connector Type: None > > | External Reference Designator: USB2 > > | External Connector Type: Access Bus (USB) > > | Port Type: USB > > | Handle 0x0011 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: USB2 > > | Internal Connector Type: None > > | External Reference Designator: USB3 > > | External Connector Type: Access Bus (USB) > > | Port Type: USB > > | Handle 0x0012 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: USB3 > > | Internal Connector Type: None > > | External Reference Designator: USB4 > > | External Connector Type: Access Bus (USB) > > | Port Type: USB > > | Handle 0x0013 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: USB4 > > | Internal Connector Type: None > > | External Reference Designator: USB5 > > | External Connector Type: Access Bus (USB) > > | Port Type: USB > > | Handle 0x0014 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: USB5 > > | Internal Connector Type: None > > | External Reference Designator: USB6 > > | External Connector Type: Access Bus (USB) > > | Port Type: USB > > | Handle 0x0015 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: COM1 > > | Internal Connector Type: 9 Pin Dual Inline (pin 10 cut) > > | External Reference Designator: COM1 > > | External Connector Type: DB-9 male > > | Port Type: Serial Port 16550A Compatible > > | Handle 0x0016 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: LPT > > | Internal Connector Type: 25 Pin Dual Inline (pin 26 cut) > > | External Reference Designator: LPT > > | External Connector Type: DB-25 male > > | Port Type: Parallel Port ECP/EPP > > | Handle 0x0017 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: KEYBOARD > > | Internal Connector Type: None > > | External Reference Designator: KEYBOARD > > | External Connector Type: PS/2 > > | Port Type: Keyboard Port > > | Handle 0x0018 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: MOUSE > > | Internal Connector Type: None > > | External Reference Designator: MOUSE > > | External Connector Type: PS/2 > > | Port Type: Mouse Port > > | Handle 0x0019 > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: Floppy > > | Internal Connector Type: On Board Floppy > > | External Reference Designator: Floppy > > | External Connector Type: None > > | Port Type: None > > | Handle 0x001A > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: Primary IDE > > | Internal Connector Type: On Board IDE > > | External Reference Designator: IDE-1 > > | External Connector Type: None > > | Port Type: None > > | Handle 0x001B > > | DMI type 8, 9 bytes. > > | Port Connector Information > > | Internal Reference Designator: Secondary IDE > > | Internal Connector Type: On Board IDE > > | External Reference Designator: IDE-2 > > | External Connector Type: None > > | Port Type: None > > | Handle 0x001C > > | DMI type 12, 5 bytes. > > | System Configuration Options > > | Option 1: System Management BIOS from Atlanta > > | Handle 0x001D > > | DMI type 13, 22 bytes. > > | BIOS Language Information > > | Installable Languages: 4 > > | English > > | Traditional Chinese > > | Simplified Chinese > > | Japanese > > | Currently Installed Language: English > > | Handle 0x001E > > | DMI type 127, 4 bytes. > > | End Of Table > > > > > > -- > > ~Randy > > - > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > Please read the FAQ at http://www.tux.org/lkml/ -- Henry Molina R&D CMN Consulting
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |