Messages in this thread | | | Subject | Re: EDD Support | From | Henry Molina <> | Date | Mon, 09 Aug 2004 12:44:42 -0500 |
| |
No Randy, no messages, I'm using insmod from BusyBox v1.00-pre10, and lsmod shows the module ok.
On Mon, 2004-08-09 at 11:35, Randy.Dunlap wrote: > On Mon, 09 Aug 2004 11:43:31 -0500 Henry Molina wrote: > > | Hi everyone, > > Hi Henry, > > | I'm compiling kernel 2.6.7 with CONFIG_EDD fine, then I proceed to > | install the module but I can't get the /proc/sys/firmware/edd entry. > | > | Any Suggestion?. > > Any kernel log messages when you load the module? > Hint: there should be. > > | Many Thanks, > | > | Henry Molina > | > | PD: I attach the dmidecode output > | > | # dmidecode 2.2 > | SMBIOS 2.3 present. > | 31 structures occupying 1017 bytes. > | Table at 0x000F0630. > | Handle 0x0000 > | DMI type 0, 20 bytes. > | BIOS Information > | Vendor: American Megatrends Inc. > | Version: 1.02 > | Release Date: 05/09/2003 > | Address: 0xF0000 > | Runtime Size: 64 kB > | ROM Size: 512 kB > | Characteristics: > | ISA is supported > | PCI is supported > | PNP is supported > | APM is supported > | BIOS is upgradeable > | BIOS shadowing is allowed > | ESCD support is available > | Boot from CD is supported > | Selectable boot is supported > | BIOS ROM is socketed > | EDD is supported > | 5.25"/360 KB floppy services are supported (int 13h) > | 5.25"/1.2 MB floppy services are supported (int 13h) > | 3.5"/720 KB floppy services are supported (int 13h) > | 3.5"/2.88 MB floppy services are supported (int 13h) > | Print screen service is supported (int 5h) > | 8042 keyboard services are supported (int 9h) > | Printer services are supported (int 17h) > | CGA/mono video services are supported (int 10h) > | ACPI is supported > | USB legacy is supported > | AGP is supported > | LS-120 boot is supported > | ATAPI Zip drive boot is supported > | BIOS boot specification is supported > | Handle 0x0001 > | DMI type 1, 25 bytes. > | System Information > | Manufacturer: Hewlett-Packard > | Product Name: HP d220 MT (DC526A) > | Version: > | Serial Number: MXD33701GQ > | UUID: 15F4C490-59EA-D711-851C-517B4801761B > | Wake-up Type: Power Switch > | Handle 0x0002 > | DMI type 2, 8 bytes. > | Base Board Information > | Manufacturer: Lite-On Tech. > | Product Name: 0888h > | Version: > | Serial Number: 01234567 > | Handle 0x0003 > | DMI type 3, 17 bytes. > | Chassis Information > | Manufacturer: Hewlett-Packard > | Type: Desktop > | Lock: Not Present > | Version: > | Serial Number: > | Asset Tag: > | Boot-up State: Safe > | Power Supply State: Safe > | Thermal State: Safe > | Security Status: None > | OEM Information: 0x00000000 > | Handle 0x0004 > | DMI type 4, 32 bytes. > | Processor Information > | Socket Designation: mPGA-478 > | Type: Central Processor > | Family: Pentium 4 > | Manufacturer: Intel > | ID: 29 0F 41 33 FF FB EB BF > | Signature: Type 0, Family 34F, Model 12, Stepping 9 > | Flags: > | FPU (Floating-point unit on-chip) > | VME (Virtual mode extension) > | DE (Debugging extension) > | PSE (Page size extension) > | TSC (Time stamp counter) > | MSR (Model specific registers) > | PAE (Physical address extension) > | MCE (Machine check exception) > | CX8 (CMPXCHG8 instruction supported) > | APIC (On-chip APIC hardware supported) > | SEP (Fast system call) > | MTRR (Memory type range registers) > | PGE (Page global enable) > | MCA (Machine check architecture) > | CMOV (Conditional move instruction supported) > | PAT (Page attribute table) > | PSE-36 (36-bit page size extension) > | CLFSH (CLFLUSH instruction supported) > | DS (Debug store) > | ACPI (ACPI supported) > | MMX (MMX technology supported) > | FXSR (Fast floating-point save and restore) > | SSE (Streaming SIMD extensions) > | SSE2 (Streaming SIMD extensions 2) > | SS (Self-snoop) > | HTT (Hyper-threading technology) > | TM (Thermal monitor supported) > | SBF (Signal break on FERR) > | Version: PENTIUM 4 > | Voltage: 2.9 V > | External Clock: 133 MHz > | Max Speed: 4000 MHz > | Current Speed: 2400 MHz > | Status: Populated, Enabled > | Upgrade: ZIF Socket > | L1 Cache Handle: 0x0005 > | L2 Cache Handle: 0x0006 > | L3 Cache Handle: Not Provided > | Handle 0x0005 > | DMI type 7, 19 bytes. > | Cache Information > | Socket Designation: Internal Cache > | Configuration: Enabled, Not Socketed, Level 1 > | Operational Mode: Write Back > | Location: Internal > | Installed Size: 8 KB > | Maximum Size: 1024 KB > | Supported SRAM Types: > | Synchronous > | Installed SRAM Type: Pipeline Burst Synchronous > | Speed: 40 ns > | Error Correction Type: Single-bit ECC > | System Type: Data > | Associativity: 4-way Set-associative > | Handle 0x0006 > | DMI type 7, 19 bytes. > | Cache Information > | Socket Designation: Internal Cache > | Configuration: Enabled, Not Socketed, Level 2 > | Operational Mode: Write Back > | Location: Internal > | Installed Size: 512 KB > | Maximum Size: 1024 KB > | Supported SRAM Types: > | Synchronous > | Installed SRAM Type: Synchronous > | Speed: 40 ns > | Error Correction Type: Parity > | System Type: Unified > | Associativity: 8-way Set-associative > | Handle 0x0007 > | DMI type 5, 20 bytes. > | Memory Controller Information > | Error Detecting Method: None > | Error Correcting Capabilities: None > | Supported Interleave: One-way Interleave > | Current Interleave: One-way Interleave > | Maximum Memory Module Size: 1024 MB > | Maximum Total Memory Size: 2048 MB > | Supported Speeds: > | Other > | Supported Memory Types: > | DIMM > | SDRAM > | Memory Module Voltage: 3.3 V > | Associated Memory Slots: 2 > | 0x0008 > | 0x0009 > | Enabled Error Correcting Capabilities: None > | Handle 0x0008 > | DMI type 6, 12 bytes. > | Memory Module Information > | Socket Designation: DIMM1 > | Bank Connections: 1 0 > | Current Speed: Unknown > | Type: DIMM SDRAM > | Installed Size: 128 MB (Single-bank Connection) > | Enabled Size: 128 MB (Single-bank Connection) > | Error Status: OK > | Handle 0x0009 > | DMI type 6, 12 bytes. > | Memory Module Information > | Socket Designation: DIMM2 > | Bank Connections: 3 2 > | Current Speed: Unknown > | Type: Unknown > | Installed Size: Not Installed (Single-bank Connection) > | Enabled Size: Not Installed (Single-bank Connection) > | Error Status: OK > | Handle 0x000A > | DMI type 9, 13 bytes. > | System Slot Information > | Designation: PCI1 > | Type: 32-bit PCI > | Current Usage: Available > | Length: Long > | ID: 1 > | Characteristics: > | 3.3 V is provided > | Opening is shared > | PME signal is supported > | Handle 0x000B > | DMI type 9, 13 bytes. > | System Slot Information > | Designation: PCI2 > | Type: 32-bit PCI > | Current Usage: Available > | Length: Long > | ID: 2 > | Characteristics: > | 3.3 V is provided > | Opening is shared > | PME signal is supported > | Handle 0x000C > | DMI type 9, 13 bytes. > | System Slot Information > | Designation: PCI3 > | Type: 32-bit PCI > | Current Usage: Available > | Length: Long > | ID: 3 > | Characteristics: > | 3.3 V is provided > | Opening is shared > | PME signal is supported > | Handle 0x000D > | DMI type 9, 13 bytes. > | System Slot Information > | Designation: AGP > | Type: 32-bit PCI > | Current Usage: Available > | Length: Long > | ID: 1 > | Characteristics: > | 3.3 V is provided > | Opening is shared > | PME signal is supported > | Handle 0x000E > | DMI type 11, 5 bytes. > | OEM Strings > | String 1: SMBIOS Support from AMI > | Handle 0x000F > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: USB0 > | Internal Connector Type: None > | External Reference Designator: USB1 > | External Connector Type: Access Bus (USB) > | Port Type: USB > | Handle 0x0010 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: USB1 > | Internal Connector Type: None > | External Reference Designator: USB2 > | External Connector Type: Access Bus (USB) > | Port Type: USB > | Handle 0x0011 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: USB2 > | Internal Connector Type: None > | External Reference Designator: USB3 > | External Connector Type: Access Bus (USB) > | Port Type: USB > | Handle 0x0012 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: USB3 > | Internal Connector Type: None > | External Reference Designator: USB4 > | External Connector Type: Access Bus (USB) > | Port Type: USB > | Handle 0x0013 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: USB4 > | Internal Connector Type: None > | External Reference Designator: USB5 > | External Connector Type: Access Bus (USB) > | Port Type: USB > | Handle 0x0014 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: USB5 > | Internal Connector Type: None > | External Reference Designator: USB6 > | External Connector Type: Access Bus (USB) > | Port Type: USB > | Handle 0x0015 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: COM1 > | Internal Connector Type: 9 Pin Dual Inline (pin 10 cut) > | External Reference Designator: COM1 > | External Connector Type: DB-9 male > | Port Type: Serial Port 16550A Compatible > | Handle 0x0016 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: LPT > | Internal Connector Type: 25 Pin Dual Inline (pin 26 cut) > | External Reference Designator: LPT > | External Connector Type: DB-25 male > | Port Type: Parallel Port ECP/EPP > | Handle 0x0017 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: KEYBOARD > | Internal Connector Type: None > | External Reference Designator: KEYBOARD > | External Connector Type: PS/2 > | Port Type: Keyboard Port > | Handle 0x0018 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: MOUSE > | Internal Connector Type: None > | External Reference Designator: MOUSE > | External Connector Type: PS/2 > | Port Type: Mouse Port > | Handle 0x0019 > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: Floppy > | Internal Connector Type: On Board Floppy > | External Reference Designator: Floppy > | External Connector Type: None > | Port Type: None > | Handle 0x001A > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: Primary IDE > | Internal Connector Type: On Board IDE > | External Reference Designator: IDE-1 > | External Connector Type: None > | Port Type: None > | Handle 0x001B > | DMI type 8, 9 bytes. > | Port Connector Information > | Internal Reference Designator: Secondary IDE > | Internal Connector Type: On Board IDE > | External Reference Designator: IDE-2 > | External Connector Type: None > | Port Type: None > | Handle 0x001C > | DMI type 12, 5 bytes. > | System Configuration Options > | Option 1: System Management BIOS from Atlanta > | Handle 0x001D > | DMI type 13, 22 bytes. > | BIOS Language Information > | Installable Languages: 4 > | English > | Traditional Chinese > | Simplified Chinese > | Japanese > | Currently Installed Language: English > | Handle 0x001E > | DMI type 127, 4 bytes. > | End Of Table > > > -- > ~Randy > - > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ -- Henry Molina R&D CMN Consulting
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |