Messages in this thread | | | Date | Sat, 07 Aug 2004 15:20:01 -0400 | From | David Ford <> | Subject | hda: dma_timer_expiry: dma status == 0x24 |
| |
My desktop is experiencing issues with DMA lately. This has been going on with the 2.6.8-rcX releases IIRC. I'm currently on rc3. The hardware is all brand new.
Scott ~ # hdparm -i /dev/hda
/dev/hda:
Model=SAMSUNG SP1614N, FwRev=TM100-23, SerialNo=0642J1FW704776 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs } RawCHS=16383/16/63, TrkSize=34902, SectSize=554, ECCbytes=4 BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 AdvancedPM=no WriteCache=enabled Drive conforms to: (null):
Scott ~ # lspci 0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01) 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South] 0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) 0000:00:08.0 RAID bus controller: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) (rev 02) 0000:00:09.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875J (rev 04) 0000:00:0a.0 Ethernet controller: 3Com Corporation 3c940 10/100/1000Base-T [Marvell] (rev 12) 0000:00:0c.0 Communication controller: Conexant HCF 56k Data/Fax Modem (rev 08) 0000:00:0d.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20) 0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80) 0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) 0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) 0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [K8T800 South] 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60) 0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge 0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge 0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge 0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge 0000:01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt hdd: irq timeout: status=0x80 { Busy } hdd: irq timeout: error=0x00 hdd: DMA disabled hdd: ATAPI reset complete hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt hda: dma_timer_expiry: dma status == 0x24 hda: DMA interrupt recovery hda: lost interrupt
Bootdata ok (command line is root=/dev/hda3 console=ttyS0,115200n8 console=tty0 serial=0,115200n8 ro noexec=on) Linux version 2.6.8-rc3 (root@Scott) (gcc version 3.4.1 (Gentoo Linux 3.4.1, ssp-3.4-2, pie-8.7.6.3)) #1 Tue Aug 3 19:44:16 EDT 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff30000 (usable) BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data) BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS) BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) No mptable found. On node 0 totalpages: 130864 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126768 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 Looks like a VIA chipset. Disabling IOMMU. Overwrite with "iommu=allowed" ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa870 ACPI: XSDT (v001 A M I OEMXSDT 0x09000323 MSFT 0x00000097) @ 0x000000001ff30100 ACPI: FADT (v003 A M I OEMFACP 0x09000323 MSFT 0x00000097) @ 0x000000001ff30290 ACPI: MADT (v001 A M I OEMAPIC 0x09000323 MSFT 0x00000097) @ 0x000000001ff30390 ACPI: OEMB (v001 A M I OEMBIOS 0x09000323 MSFT 0x00000097) @ 0x000000001ff40040 ACPI: DSDT (v001 SK8V_ SK8V_013 0x00000013 MSFT 0x0100000d) @ 0x0000000000000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:5 APIC version 16 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: Assigned apic_id 1 IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information Built 1 zonelists Kernel command line: root=/dev/hda3 console=ttyS0,115200n8 console=tty0 serial=0,115200n8 ro noexec=on Initializing CPU#0 PID hash table entries: 16 (order 4: 256 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 2200.182 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 506728k/523456k available (4335k kernel code, 15988k reserved, 2255k data, 192k init) Calibrating delay loop... 4308.99 BogoMIPS Mount-cache hash table entries: 256 (order: 0, 4096 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: AMD Opteron(tm) Processor 148 stepping 08 Using local APIC NMI watchdog using perfctr0 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 Using local APIC timer interrupts. Detected 12.501 MHz APIC timer. NET: Registered protocol family 16 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing IOAPIC[0]: Set PCI routing entry (1-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169 IOAPIC[0]: Set PCI routing entry (1-18 -> 0xb1 -> IRQ 18 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177 ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 169 IOAPIC[0]: Set PCI routing entry (1-17 -> 0xb9 -> IRQ 17 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 185 ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177 IOAPIC[0]: Set PCI routing entry (1-20 -> 0xc1 -> IRQ 20 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 193 IOAPIC[0]: Set PCI routing entry (1-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 201 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 201 IOAPIC[0]: Set PCI routing entry (1-22 -> 0xd1 -> IRQ 22 Mode:1 Active:1) ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 number of MP IRQ sources: 15. number of IO-APIC #1 registers: 24. testing the IO APIC.......................
IO APIC #1...... .... register #00: 01000000 ....... : physical APIC id: 01 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 0 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 001 01 1 1 0 1 0 1 1 A9 11 001 01 1 1 0 1 0 1 1 B9 12 001 01 1 1 0 1 0 1 1 B1 13 000 00 1 0 0 0 0 0 0 00 14 001 01 1 1 0 1 0 1 1 C1 15 001 01 1 1 0 1 0 1 1 C9 16 001 01 1 1 0 1 0 1 1 D1 17 0F2 02 1 0 0 0 0 0 2 13 Using vector-based indexing IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ169 -> 0:16 IRQ185 -> 0:17 IRQ177 -> 0:18 IRQ193 -> 0:20 IRQ201 -> 0:21 IRQ209 -> 0:22 .................................... done. TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca) agpgart: Detected AGP bridge 0 agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xf0000000 PCI-DMA: Disabling IOMMU. IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 udf: registering filesystem Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.0, from 5 to 9 PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 9 PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9 PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9 ACPI: Power Button (FF) [PWRF] ACPI: Sleep Button (CM) [SLPB] ACPI: Processor [CPU1] (supports C1) Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.100 (c) Dave Jones Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds). Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A IOAPIC[0]: Set PCI routing entry (1-4 -> 0x49 -> IRQ 4 Mode:0 Active:0) Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185 sk98lin: Network Device Driver v6.23 (C)Copyright 1999-2004 Marvell(R). ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185 eth0: 3Com Gigabit LOM (3C940) PrefPort:A RlmtMode:Check Link State ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177 Linux Tulip driver version 1.1.13 (May 11, 2002) ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 18 (level, low) -> IRQ 177 tulip0: MII transceiver #1 config 3000 status 7829 advertising 01e1. eth1: Lite-On 82c168 PNIC rev 32 at 0xb000, 00:A0:CC:56:CB:FB, IRQ 177. netconsole: not configured, aborting Linux video capture interface: v1.00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 193 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA hda: SAMSUNG SP1614N, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: SONY DVD RW DRU-700A, ATAPI CD/DVD-ROM drive hdd: 4X4X32, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 1024KiB hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 PCI: Enabling device 0000:00:09.0 (0000 -> 0003) ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:09.0 to 64 sym0: <875> rev 0x4 at pci 0000:00:09.0 irq 169 sym0: Symbios NVRAM, ID 15, Fast-20, SE, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: SCAN FOR LUNS disabled for targets 1. sym0: SCSI BUS has been reset. scsi0 : sym-2.1.18j Vendor: UMAX Model: Astra 2400S Rev: V1.1 Type: Scanner ANSI SCSI revision: 02 scsi(0:0:1:0): Beginning Domain Validation scsi(0:0:1:0): Ending Domain Validation 3ware 9000 Storage Controller device driver for Linux v2.26.02.001. libata version 1.02 loaded. sata_promise version 1.00 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 18 (level, low) -> IRQ 177 ata1: SATA max UDMA/133 cmd 0xFFFFFF0000067200 ctl 0xFFFFFF0000067238 bmdma 0x0 irq 177 ata2: SATA max UDMA/133 cmd 0xFFFFFF0000067280 ctl 0xFFFFFF00000672B8 bmdma 0x0 irq 177 ata1: no device found (phy stat 00000000) scsi1 : sata_promise ata2: no device found (phy stat 00000000) scsi2 : sata_promise sata_via version 0.20 ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193 sata_via(0000:00:0f.0): routed to hard irq line 11 ata3: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD400 irq 193 ata4: SATA max UDMA/133 cmd 0xE000 ctl 0xD802 bmdma 0xD408 irq 193 ata3: no device found (phy stat 00000000) scsi3 : sata_via ata4: no device found (phy stat 00000000) scsi4 : sata_via Attached scsi generic sg0 at scsi0, channel 0, id 1, lun 0, type 6 ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org> ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[169] MMIO=[fde00000-fde007ff] Max Packet=[2048] video1394: Installed video1394 module ieee1394: raw1394: /dev/raw1394 device initialized sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org> ip1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org> ip1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) ieee1394: Loaded AMDTP driver ieee1394: Loaded CMP driver ehci_hcd: block sizes: qh 192 qtd 96 itd 192 sitd 96 ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 201 ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 ehci_hcd 0000:00:10.4: reset hcs_params 0x4208 dbg=0 cc=4 pcc=2 ordered !ppc ports=8 ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024 ehci_hcd 0000:00:10.4: capability 0001 at 68 ehci_hcd 0000:00:10.4: irq 201, pci mem ffffff00000a4000 ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 ehci_hcd 0000:00:10.4: supports USB remote wakeup usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409 usb usb1: Product: VIA Technologies, Inc. USB 2.0 usb usb1: Manufacturer: Linux 2.6.8-rc3 ehci_hcd usb usb1: SerialNumber: 0000:00:10.4 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: ganged power switching hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: Single TT hub 1-0:1.0: TT requires at most 8 FS bit times hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports usbcore: registered new driver cdc_acm drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 input: PS2T++ Logitech TouchPad 3 on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s input: AT Translated Set 2 keyboard on isa0060/serio0 i2c /dev entries driver hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 hub 1-0:1.0: port 1 not reset yet, waiting 50ms ehci_hcd 0000:00:10.4: port 1 full speed --> companion ehci_hcd 0000:00:10.4: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT ehci_hcd 0000:00:10.4: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501 hub 1-0:1.0: port 6 not reset yet, waiting 50ms ehci_hcd 0000:00:10.4: port 6 full speed --> companion ehci_hcd 0000:00:10.4: GetStatus port 6 status 003001 POWER OWNER sig=se0 CONNECT ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800005eb58e] Driver for 1-wire Dallas network protocol. Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC). via82xx: Assuming DXS channels with 48k fixed sample rate. Please try dxs_support=1 or dxs_support=4 option and report if it works on your machine. ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 209 PCI: Setting latency timer of device 0000:00:11.5 to 64 codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] codec_read: codec 0 is not valid [0xfe0000] ALSA device list: #0: VIA 823x rev60 at 0xc800, irq 209 u32 classifier Perfomance counters on input device check on Actions configured NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 28Kbytes TCP: Hash tables configured (established 32768 bind 4681) IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered NET: Registered protocol family 4 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> SCTP: Hash tables configured (established 16384 bind 2340) sctp_init_sock(sk: 000001001f9910a8) powernow-k8: Power state transitions not supported ACPI: (supports S0 S1 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 192k freed Adding 498004k swap on /dev/hda2. Priority:-1 extents:1 hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 201 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 201, io base 000000000000b400 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: detected 2 ports usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: default language 0x0409 usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller usb usb2: Manufacturer: Linux 2.6.8-rc3 uhci_hcd usb usb2: SerialNumber: 0000:00:10.0 usb usb2: hotplug usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 201 uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) ehci_hcd 0000:00:10.4: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s uhci_hcd 0000:00:10.1: irq 201, io base 000000000000b800 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: detected 2 ports usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: default language 0x0409 usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) usb usb3: Manufacturer: Linux 2.6.8-rc3 uhci_hcd usb usb3: SerialNumber: 0000:00:10.1 usb usb3: hotplug usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 201 uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:10.4: port 1 full speed --> companion ehci_hcd 0000:00:10.4: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECT ehci_hcd 0000:00:10.4: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 6, status 0501, change 0001, 480 Mb/s uhci_hcd 0000:00:10.2: irq 201, io base 000000000000c000 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: detected 2 ports usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: default language 0x0409 usb usb4: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) usb usb4: Manufacturer: Linux 2.6.8-rc3 uhci_hcd usb usb4: SerialNumber: 0000:00:10.2 usb usb4: hotplug usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: hotplug hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: no power switching (usb 1.0) hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: power on to power good time: 2ms hub 4-0:1.0: local power source is good ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 201 uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) uhci_hcd 0000:00:10.3: irq 201, io base 000000000000c400 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: detected 2 ports usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: default language 0x0409 usb usb5: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) usb usb5: Manufacturer: Linux 2.6.8-rc3 uhci_hcd usb usb5: SerialNumber: 0000:00:10.3 usb usb5: hotplug usb usb5: adding 5-0:1.0 (config #1, interface 0) usb 5-0:1.0: hotplug hub 5-0:1.0: usb_probe_interface hub 5-0:1.0: usb_probe_interface - got id hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 1-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501 hub 1-0:1.0: port 6 not reset yet, waiting 50ms ehci_hcd 0000:00:10.4: port 6 full speed --> companion ehci_hcd 0000:00:10.4: GetStatus port 6 status 003001 POWER OWNER sig=se0 CONNECT uhci_hcd 0000:00:10.0: port 1 portsc 009b hub 2-0:1.0: port 1, status 0101, change 0003, 12 Mb/s hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 usb 2-1: new full speed USB device using address 2 usb 2-1: skipped 1 descriptor after interface usb 2-1: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 2-1: hotplug usb 2-1: adding 2-1:1.0 (config #1, interface 0) usb 2-1:1.0: hotplug hub 2-1:1.0: usb_probe_interface hub 2-1:1.0: usb_probe_interface - got id hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected hub 2-1:1.0: standalone hub hub 2-1:1.0: individual port power switching hub 2-1:1.0: individual port over-current protection hub 2-1:1.0: power on to power good time: 100ms hub 2-1:1.0: local power source is good hub 2-1:1.0: enabling power on all ports uhci_hcd 0000:00:10.0: port 2 portsc 018a hub 2-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.1: port 1 portsc 018a hub 3-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.1: port 2 portsc 008a hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 uhci_hcd 0000:00:10.2: port 1 portsc 018a hub 4-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.2: port 2 portsc 009b hub 4-0:1.0: port 2, status 0101, change 0003, 12 Mb/s hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 usb 4-2: new full speed USB device using address 2 usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 4-2: default language 0x0409 usb 4-2: Product: EZ USB/Ethernet Converter usb 4-2: Manufacturer: SMC, Inc usb 4-2: SerialNumber: 0001 usb 4-2: hotplug usb 4-2: adding 4-2:1.0 (config #1, interface 0) usb 4-2:1.0: hotplug uhci_hcd 0000:00:10.3: port 1 portsc 018a hub 5-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s drivers/usb/net/pegasus.c: v0.5.12 (2003/06/06):Pegasus/Pegasus II USB Ethernet driver pegasus 4-2:1.0: usb_probe_interface pegasus 4-2:1.0: usb_probe_interface - got id eth3: SMC 202 USB Ethernet usbcore: registered new driver pegasus hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300 uhci_hcd 0000:00:10.3: port 2 portsc 018a hub 5-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s uhci_hcd 0000:00:10.1: suspend_hc hub 5-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x300 hub 2-1:1.0: port 1, status 0301, change 0001, 1.5 Mb/s hub 2-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 usb 2-1.1: new low speed USB device using address 3 usb 2-1.1: skipped 1 descriptor after interface usb 2-1.1: new device strings: Mfr=3, Product=1, SerialNumber=2 usb 2-1.1: default language 0x0409 usb 2-1.1: Product: Back-UPS ES 350 FW:1.e2.D USB FW:e2 usb 2-1.1: Manufacturer: APC usb 2-1.1: SerialNumber: AB0303246275 usb 2-1.1: hotplug usb 2-1.1: adding 2-1.1:1.0 (config #1, interface 0) usb 2-1.1:1.0: hotplug usbhid 2-1.1:1.0: usb_probe_interface usbhid 2-1.1:1.0: usb_probe_interface - got id uhci_hcd 0000:00:10.3: suspend_hc drivers/usb/core/file.c: looking for a minor, starting at 0 hiddev0: USB HID v1.10 Device [APC Back-UPS ES 350 FW:1.e2.D USB FW:e2] on usb-0000:00:10.0-1.1 hub 2-1:1.0: port 2, status 0301, change 0001, 1.5 Mb/s hub 2-1:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 hub 2-1:1.0: port 2 not reset yet, waiting 10ms usb 2-1.2: new low speed USB device using address 4 usb 2-1.2: skipped 1 descriptor after interface usb 2-1.2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-1.2: default language 0x0409 usb 2-1.2: Product: USB Receiver usb 2-1.2: Manufacturer: Logitech usb 2-1.2: hotplug usb 2-1.2: adding 2-1.2:1.0 (config #1, interface 0) usb 2-1.2:1.0: hotplug usbhid 2-1.2:1.0: usb_probe_interface usbhid 2-1.2:1.0: usb_probe_interface - got id input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-1.2 hub 2-1:1.0: port 3, status 0101, change 0001, 12 Mb/s hub 2-1:1.0: debounce: port 3: total 100ms stable 100ms status 0x101 hub 2-1:1.0: port 3 not reset yet, waiting 10ms usb 2-1.3: new full speed USB device using address 5 usb 2-1.3: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 2-1.3: hotplug usb 2-1.3: adding 2-1.3:1.0 (config #1, interface 0) usb 2-1.3:1.0: hotplug usbcore: registered new driver ov511 drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver ov511 2-1.3:1.0: usb_probe_interface ov511 2-1.3:1.0: usb_probe_interface - got id drivers/usb/media/ov511.c: USB OV511 video device found drivers/usb/media/ov511.c: model: AverMedia InterCam Elite drivers/usb/media/ov511.c: Sensor is an OV7610 drivers/usb/media/ov511.c: Device at usb-0000:00:10.0-1.3 registered to minor 0 hub 2-1:1.0: port 4, status 0101, change 0001, 12 Mb/s hub 2-1:1.0: debounce: port 4: total 100ms stable 100ms status 0x101 hub 2-1:1.0: port 4 not reset yet, waiting 10ms usb 2-1.4: new full speed USB device using address 6 usb 2-1.4: new device strings: Mfr=0, Product=1, SerialNumber=0 usb 2-1.4: default language 0x0409 usb 2-1.4: Product: Camera usb 2-1.4: hotplug usb 2-1.4: adding 2-1.4:1.0 (config #1, interface 0) usb 2-1.4:1.0: hotplug Disabled Privacy Extensions on device ffffffff806da5c0(lo) cable: network connection up using port A speed: 100 autonegotiation: yes duplex mode: full flowctrl: none irq moderation: disabled scatter-gather: enabled ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (2044 buckets, 16352 max) - 480 bytes per conntrack intranet: Setting full-duplex based on MII#1 link partner capability of 45e1. begin:vcard fn:David Ford n:Ford;David email;internet:david@blue-labs.org title:Industrial Geek tel;home:Ask please tel;cell:(203) 650-3611 x-mozilla-html:TRUE version:2.1 end:vcard
| |