lkml.org 
[lkml]   [2004]   [Aug]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: SCSI Bus Parity errors with all Kernels after 2.4.26
 >> I have a machine conf. which runs fine under a variety of older
>> kernels and fails under a variety of newer ones. I was hoping someone
>> could direct me to a person who would like to look further into this.
...

>What are the exact error messages? CC linux-scsi@xxxxxxxxxxxxxxx

Under SuSE 9.1 the output during module loading is as follows:
-------------------------------------------------------
SCSI subsystem initialized
PCI: Found IRQ 5 for device 0000:00:0a.0
sym0: <875> rev 0x4 at pci 0000:00:0a.0 irq 5
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18i
Vendor: IOMEGA Model: ZIP 100 Rev: J.03
Type: Direct-Access ANSI SCSI revision: 02
sym0:5:0:phase change 6-7 6@3738cf84 resid=4.
Attached scsi removable disk sda at scsi0, channel 0, id 5, lin0
Attached scsi generic sg0 at scsi0, channel 0, id 5, lun 0, type 0
Vendor: PIONEER Model: CD-ROM DR-U065 Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
sym0:6: FAST-20 SCSI 19.2 MB/s ST (52.0 ns, offset 16)
Uniform CD-ROM driver Revision: 3.20
Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 5
PCI: Found IRQ 11 for device 0000:00:0c.0
sym1: <895> rev 0x1 at pci 0000:00:0c.0 irq 11
sym1: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: SCSI BUS has been reset.
scsi1 : sym-2.1.18i
Vendor: QUANTUM Model: VIKING II 4.5WLS Rev: 4110
Type: Direct-Access ANSI SCSI revision: 02
sym1:0:0: tagged command queuind enabled, command queue depth 16.
sym1:0: FAST-40 WIDE SCSI 80.0 MB/s ST (25.0 ns, offset 31)
SCSI device sdb: 8910423 512-byte hdwr sectors (4562 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi1, channel 0, id 0, lun 0, type 0
Vendor: IBM Model: DNES-309170W Rev: SAH0
Type: Direct-Access ANSI SCSI revision: 03
sym1:6:0: tagged command queuing enabled, command queue depth 16.
sym1:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25.0 ns, offset 30)
SCSI: device sdc: 17916240 512-byte hdwr sectors (9173 MB)
SCSI device sdc: drive cache: write back
sdc: sdc1 sdc2
Attached scsi disk sdc at scsi1, channel 0, id 6, lun 0
Attached scsi generic sg3 at scsi1, channel 0, id 6, lun 0, type 0
sym0: SCSI parity error detected: SCR1=1 DBC=50000000 SBCL=0
sym0:15: ERROR (a0:0) (8-0-0) (0/5/0) @ (mem cd800020:cd800020).
sym0: regdump: da 00 00 05 47 00 0f 0e 00 08 00 00 80 00 0f 02 ff ff ff
00 02 ff ff ff.
sym0: PCI STATUS = 0x20000
sym0: SCSI BUS reset detected.
sym0: SCSI BUS has been reset.
sym1: SCSI parity error detected: SCR1=1 DBC=50000000 SBCL=0
sym1: SCSI phase error fixup: CCB already dequeued.
sym1:15: ERROR (81:0) (8-0-0) (0/7/0) @ (scripta 48:a9100786).
sym1: script cmd = f31c0004
sym1: regdump: da 00 00 07 47 00 0f 0a 00 08 86 00 80 00 0f 02 28 71 01
37 02 ff ff ff.
sym1: SCSI BUS reset detected.
sym1: SCSI BUS has been reset.
---------------------------------------------------
Please cc: rnelson@airflwosciences.com since I do not subscribe. Note
that I will be out of town for the next 5 days.

Bob Nelson

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:05    [W:0.140 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site