lkml.org 
[lkml]   [2004]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [PATCH] acpiphp extension for 2.6.7
From
Date
On Thu, 2004-06-24 at 14:45, Greg KH wrote: 
> The LED stuff looks good (few minor comments below), but the ACPI table
> info should be moved to the ACPI core to provide this to all ACPI tables
> in the /sys/firmware/acpi tree.

I took it out of this patch, but it might be a while until I can figure
out how to correctly modify the ACPI core to do that...

But the rest of your changes I implemented and have included in this
patch.

--Vernon



diff -X ignore_files -Nur linux-2.6.7.orig/drivers/pci/hotplug/Kconfig linux-2.6.7-apci/drivers/pci/hotplug/Kconfig
--- linux-2.6.7.orig/drivers/pci/hotplug/Kconfig 2004-06-15 22:19:17.000000000 -0700
+++ linux-2.6.7-apci/drivers/pci/hotplug/Kconfig 2004-06-22 11:49:38.000000000 -0700
@@ -88,6 +88,18 @@

When in doubt, say N.

+config HOTPLUG_PCI_ACPI_IBM
+ tristate "ACPI PCI Hotplug driver IBM extensions"
+ depends on HOTPLUG_PCI_ACPI
+ help
+ Say Y here if you have an IBM system that supports PCI Hotplug using
+ ACPI.
+
+ To compile this driver as a module, choose M here: the
+ module will be called acpiphp_ibm.
+
+ When in doubt, say N.
+
config HOTPLUG_PCI_CPCI
bool "CompactPCI Hotplug driver"
depends on HOTPLUG_PCI
diff -X ignore_files -Nur linux-2.6.7.orig/drivers/pci/hotplug/Makefile linux-2.6.7-apci/drivers/pci/hotplug/Makefile
--- linux-2.6.7.orig/drivers/pci/hotplug/Makefile 2004-06-15 22:19:43.000000000 -0700
+++ linux-2.6.7-apci/drivers/pci/hotplug/Makefile 2004-06-22 11:49:38.000000000 -0700
@@ -7,6 +7,7 @@
obj-$(CONFIG_HOTPLUG_PCI_COMPAQ) += cpqphp.o
obj-$(CONFIG_HOTPLUG_PCI_IBM) += ibmphp.o
obj-$(CONFIG_HOTPLUG_PCI_ACPI) += acpiphp.o
+obj-$(CONFIG_HOTPLUG_PCI_ACPI_IBM) += acpiphp_ibm.o
obj-$(CONFIG_HOTPLUG_PCI_CPCI_ZT5550) += cpcihp_zt5550.o
obj-$(CONFIG_HOTPLUG_PCI_CPCI_GENERIC) += cpcihp_generic.o
obj-$(CONFIG_HOTPLUG_PCI_PCIE) += pciehp.o
diff -X ignore_files -Nur linux-2.6.7.orig/drivers/pci/hotplug/acpiphp.h linux-2.6.7-apci/drivers/pci/hotplug/acpiphp.h
--- linux-2.6.7.orig/drivers/pci/hotplug/acpiphp.h 2004-06-15 22:20:26.000000000 -0700
+++ linux-2.6.7-apci/drivers/pci/hotplug/acpiphp.h 2004-06-22 11:49:38.000000000 -0700
@@ -172,6 +172,22 @@
};


+/**
+ * struct acpiphp_attention_info - device specific attention registration
+ *
+ * ACPI has no generic method of setting/getting attention status
+ * this allows for device specific driver registration
+ */
+typedef int (*acpiphp_set_attn_callback)(struct hotplug_slot *slot, u8 status);
+typedef int (*acpiphp_get_attn_callback)(struct hotplug_slot *slot, u8 *status);
+struct acpiphp_attention_info
+{
+ acpiphp_set_attn_callback set_attn;
+ acpiphp_get_attn_callback get_attn;
+ struct module *owner;
+};
+
+
/* PCI bus bridge HID */
#define ACPI_PCI_HOST_HID "PNP0A03"

@@ -212,6 +228,12 @@

/* function prototypes */

+/* acpiphp_core.c */
+extern int acpiphp_register_attention_info(
+ struct acpiphp_attention_info*info);
+extern int acpiphp_unregister_attention_info(
+ struct acpiphp_attention_info *info);
+
/* acpiphp_glue.c */
extern int acpiphp_glue_init (void);
extern void acpiphp_glue_exit (void);
diff -X ignore_files -Nur linux-2.6.7.orig/drivers/pci/hotplug/acpiphp_core.c linux-2.6.7-apci/drivers/pci/hotplug/acpiphp_core.c
--- linux-2.6.7.orig/drivers/pci/hotplug/acpiphp_core.c 2004-06-15 22:19:37.000000000 -0700
+++ linux-2.6.7-apci/drivers/pci/hotplug/acpiphp_core.c 2004-06-29 11:12:41.754945480 -0700
@@ -51,6 +51,7 @@

/* local variables */
static int num_slots;
+static struct acpiphp_attention_info *attention_info = NULL;

#define DRIVER_VERSION "0.4"
#define DRIVER_AUTHOR "Greg Kroah-Hartman <gregkh@us.ibm.com>, Takayoshi Kochi <t-kochi@bq.jp.nec.com>"
@@ -62,10 +63,15 @@
MODULE_PARM_DESC(debug, "Debugging mode enabled or not");
module_param(debug, bool, 644);

+/* export the attention callback registration methods */
+EXPORT_SYMBOL_GPL(acpiphp_register_attention_info);
+EXPORT_SYMBOL_GPL(acpiphp_unregister_attention_info);
+
static int enable_slot (struct hotplug_slot *slot);
static int disable_slot (struct hotplug_slot *slot);
static int set_attention_status (struct hotplug_slot *slot, u8 value);
static int get_power_status (struct hotplug_slot *slot, u8 *value);
+static int get_attention_status (struct hotplug_slot *slot, u8 *value);
static int get_address (struct hotplug_slot *slot, u32 *value);
static int get_latch_status (struct hotplug_slot *slot, u8 *value);
static int get_adapter_status (struct hotplug_slot *slot, u8 *value);
@@ -76,11 +82,54 @@
.disable_slot = disable_slot,
.set_attention_status = set_attention_status,
.get_power_status = get_power_status,
+ .get_attention_status = get_attention_status,
.get_latch_status = get_latch_status,
.get_adapter_status = get_adapter_status,
.get_address = get_address,
};

+
+/**
+ * acpiphp_register_attention_info - set attention LED callback
+ *
+ * this is used to register a hardware specific acpi driver
+ * that manipulates the attention LED. All the fields in
+ * info must be set.
+ *
+ */
+int acpiphp_register_attention_info(struct acpiphp_attention_info *info)
+{
+ int retval = -1;
+
+ if (info && info->owner && info->set_attn &&
+ info->get_attn && !attention_info) {
+ retval = 0;
+ attention_info = info;
+ }
+ return retval;
+}
+
+
+/**
+ * acpiphp_unregister_attention_info - unset attention LED callback
+ *
+ * this is used to un-register a hardware specific acpi driver
+ * that manipulates the attention LED. The pointer to the
+ * info struct must be the same as the one used to set it.
+ *
+ */
+int acpiphp_unregister_attention_info(struct acpiphp_attention_info *info)
+{
+ int retval = -1;
+
+ if (info && attention_info == info) {
+ attention_info = NULL;
+ retval = 0;
+ }
+ return retval;
+}
+
+
/**
* enable_slot - power on and enable a slot
* @hotplug_slot: slot to enable
@@ -120,29 +169,24 @@
/**
* set_attention_status - set attention LED
*
- * TBD:
* ACPI doesn't have known method to manipulate
- * attention status LED.
+ * attention status LED, so we use a callback that
+ * was registered with us. This allows hardware specific
+ * ACPI implementations to blink the light for us.
*
*/
static int set_attention_status(struct hotplug_slot *hotplug_slot, u8 status)
{
+ int retval = -1;
+
dbg("%s - physical_slot = %s\n", __FUNCTION__, hotplug_slot->name);

- switch (status) {
- case 0:
- /* FIXME turn light off */
- hotplug_slot->info->attention_status = 0;
- break;
-
- case 1:
- default:
- /* FIXME turn light on */
- hotplug_slot->info->attention_status = 1;
- break;
+ if (attention_info && attention_info->set_attn &&
+ try_module_get(attention_info->owner)) {
+ retval = attention_info->set_attn(hotplug_slot, status);
+ module_put(attention_info->owner);
}
-
- return 0;
+ return retval;
}

/**
@@ -166,6 +210,30 @@
}

/**
+ * get_attention_status - get attention LED status
+ *
+ * ACPI doesn't have known method to determine the state
+ * of the attention status LED, so we use a callback that
+ * was registered with us. This allows hardware specific
+ * ACPI implementations to determine its state
+ *
+ */
+static int get_attention_status (struct hotplug_slot *hotplug_slot, u8 *value)
+{
+ int retval = -1;
+
+ dbg("%s - physical_slot = %s\n", __FUNCTION__, hotplug_slot->name);
+
+ if (attention_info && attention_info->get_attn &&
+ try_module_get(attention_info->owner)) {
+ retval = attention_info->get_attn(hotplug_slot, value);
+ module_put(attention_info->owner);
+ }
+ return retval;
+}
+
+
+/**
* get_latch_status - get latch status of a slot
* @hotplug_slot: slot to get status
* @value: pointer to store status
@@ -307,7 +375,7 @@

slot->acpi_slot = get_slot_from_id(i);
slot->hotplug_slot->info->power_status = acpiphp_get_power_status(slot->acpi_slot);
- slot->hotplug_slot->info->attention_status = acpiphp_get_attention_status(slot->acpi_slot);
+ slot->hotplug_slot->info->attention_status = 0;
slot->hotplug_slot->info->latch_status = acpiphp_get_latch_status(slot->acpi_slot);
slot->hotplug_slot->info->adapter_status = acpiphp_get_adapter_status(slot->acpi_slot);
slot->hotplug_slot->info->max_bus_speed = PCI_SPEED_UNKNOWN;
diff -X ignore_files -Nur linux-2.6.7.orig/drivers/pci/hotplug/acpiphp_glue.c linux-2.6.7-apci/drivers/pci/hotplug/acpiphp_glue.c
--- linux-2.6.7.orig/drivers/pci/hotplug/acpiphp_glue.c 2004-06-15 22:19:10.000000000 -0700
+++ linux-2.6.7-apci/drivers/pci/hotplug/acpiphp_glue.c 2004-06-22 11:49:38.000000000 -0700
@@ -1302,20 +1302,6 @@


/*
- * attention LED ON: 1
- * OFF: 0
- *
- * TBD
- * no direct attention led status information via ACPI
- *
- */
-u8 acpiphp_get_attention_status(struct acpiphp_slot *slot)
-{
- return 0;
-}
-
-
-/*
* latch closed: 1
* latch open: 0
*/
diff -X ignore_files -Nur linux-2.6.7.orig/drivers/pci/hotplug/acpiphp_ibm.c linux-2.6.7-apci/drivers/pci/hotplug/acpiphp_ibm.c
--- linux-2.6.7.orig/drivers/pci/hotplug/acpiphp_ibm.c 1969-12-31 16:00:00.000000000 -0800
+++ linux-2.6.7-apci/drivers/pci/hotplug/acpiphp_ibm.c 2004-06-29 11:35:37.843748184 -0700
@@ -0,0 +1,426 @@
+/*
+ * ACPI PCI Hot Plug IBM Extension
+ *
+ * Copyright (C) 2004 Vernon Mauery <vernux@us.ibm.com>
+ * Copyright (C) 2004 IBM Corp.
+ *
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
+ * NON INFRINGEMENT. See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Send feedback to <vernux@us.ibm.com>
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <acpi/acpi_bus.h>
+#include <asm/uaccess.h>
+
+#include "acpiphp.h"
+#include "pci_hotplug.h"
+
+#define DRIVER_VERSION "1.0.1"
+#define DRIVER_AUTHOR "Irene Zubarev <zubarev@us.ibm.com>, Vernon Mauery <vernux@us.ibm.com>"
+#define DRIVER_DESC "ACPI Hot Plug PCI Controller Driver IBM extension"
+
+static int debug;
+
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRIVER_VERSION);
+MODULE_PARM(debug, "i");
+MODULE_PARM_DESC(debug, " Debugging mode enabled or not");
+#define MY_NAME "acpiphp_ibm"
+
+#ifdef dbg
+#undef dbg
+#endif
+#define dbg(format, arg...) \
+do { \
+ if (debug) \
+ printk(KERN_DEBUG "%s: " format, \
+ MY_NAME , ## arg); \
+} while (0)
+
+#define FOUND_APCI 0x61504349
+/* these are the names for the IBM ACPI pseudo-device */
+#define IBM_HARDWARE_ID1 "IBM37D0"
+#define IBM_HARDWARE_ID2 "IBM37D4"
+
+/* union apci_descriptor - allows access to the
+ * various device descriptors that are embedded in the
+ * aPCI table
+ */
+union apci_descriptor {
+ struct {
+ char sig[4];
+ u8 len;
+ } header;
+ struct {
+ u8 type;
+ u8 len;
+ u16 slot_id;
+ u8 bus_id;
+ u8 dev_num;
+ u8 slot_num;
+ u8 slot_attr[2];
+ u8 attn;
+ u8 status[2];
+ u8 sun;
+ } slot;
+ struct {
+ u8 type;
+ u8 len;
+ } generic;
+};
+
+/* struct notification - keeps info about the device
+ * that cause the ACPI notification event
+ */
+struct notification {
+ struct acpi_device *device;
+ u8 event;
+};
+
+/* forward declarations of functions for this module
+ */
+static int ibm_set_attention_status (struct hotplug_slot *slot, u8 status);
+static int ibm_get_attention_status (struct hotplug_slot *slot, u8 *status);
+static void ibm_handle_events(acpi_handle handle, u32 event, void *context);
+static int ibm_get_table_from_acpi(char **bufp);
+static acpi_status __init ibm_find_acpi_device(acpi_handle handle,
+ u32 lvl, void *context, void **rv);
+static int __init ibm_acpiphp_init(void);
+static void __exit ibm_acpiphp_exit(void);
+
+/* static global variables
+ */
+static acpi_handle ibm_acpi_handle = NULL;
+static struct notification ibm_note;
+static struct acpiphp_attention_info ibm_attention_info =
+{
+ .set_attn = ibm_set_attention_status,
+ .get_attn = ibm_get_attention_status,
+ .owner = THIS_MODULE,
+};
+
+
+/*
+ * ibm_set_attention_status - callback method to set the attention LED
+ *
+ * this method is registered with the acpiphp module as a callback
+ * to do the device specific task of setting the LED status
+ *
+ */
+static int ibm_set_attention_status (struct hotplug_slot *slot, u8 status)
+{
+ int retval = 0;
+ union acpi_object args[2];
+ struct acpi_object_list params = { .pointer = args, .count = 2 };
+ acpi_status stat;
+ unsigned long rc = 0;
+ struct acpiphp_slot *acpi_slot;
+
+ if (!slot || !slot->private)
+ return -1;
+ acpi_slot = ((struct slot *)(slot->private))->acpi_slot;
+ if (!acpi_slot)
+ return -1;
+
+ dbg("%s: set slot %d attention status to %d\n", __FUNCTION__,
+ acpi_slot->sun, (status ? 1 : 0));
+
+ args[0].type = ACPI_TYPE_INTEGER;
+ args[0].integer.value = acpi_slot->sun;
+ args[1].type = ACPI_TYPE_INTEGER;
+ args[1].integer.value = (status) ? 1 : 0;
+
+ stat = acpi_evaluate_integer(ibm_acpi_handle, "APLS", &params, &rc);
+ if (ACPI_FAILURE(stat)) {
+ retval = -1;
+ err("APLS evaluation failed: 0x%08x\n", stat);
+ } else if (!rc) {
+ retval = -1;
+ err("APLS method failed: 0x%08lx\n", rc);
+ }
+ return retval;
+}
+
+/*
+ * ibm_get_attention_status - callback method to get attention LED status
+ *
+ * this method is registered with the acpiphp module as a callback
+ * to do the device specific task of getting the LED status
+ *
+ * Because there is no direct method of getting the LED status directly
+ * from an ACPI call, we read the aPCI table and parse out our
+ * slot descriptor to read the status from that.
+ *
+ */
+static int ibm_get_attention_status (struct hotplug_slot *slot, u8 *status)
+{
+ int retval = -1, ind = 0, size;
+ char *table = NULL;
+ struct acpiphp_slot *acpi_slot;
+ union apci_descriptor *des;
+
+ if (!slot || !slot->private)
+ goto get_attn_done;
+ acpi_slot = ((struct slot *)(slot->private))->acpi_slot;
+ if (!acpi_slot)
+ goto get_attn_done;
+
+ size = ibm_get_table_from_acpi(&table);
+ if (size <= 0 || !table)
+ goto get_attn_done;
+ // read the header
+ des = (union apci_descriptor *)&table[ind];
+ if (memcmp(des->header.sig, "aPCI", 4) != 0)
+ goto get_attn_done;
+ des = (union apci_descriptor *)&table[ind += des->header.len];
+ while (ind < size && (des->generic.type != 0x82 ||
+ des->slot.slot_id != acpi_slot->sun))
+ des = (union apci_descriptor *)&table[ind += des->generic.len];
+ if (ind < size && des->slot.slot_id == acpi_slot->sun) {
+ retval = 0;
+ if (des->slot.attn & 0xa0 || des->slot.status[1] & 0x08)
+ *status = 1;
+ else
+ *status = 0;
+ }
+
+ dbg("%s: get slot %d attention status is %d retval=%x\n",
+ __FUNCTION__, acpi_slot->sun, *status, retval);
+
+get_attn_done:
+ if (table)
+ kfree(table);
+ return retval;
+}
+
+/*
+ * ibm_handle_events - listens for ACPI events for the IBM37D0 device
+ *
+ * this method is registered as a callback with the ACPI subsystem
+ * it is called when this device has an event to notify the OS of
+ *
+ * the events actually come from the device as two events that get
+ * synthesized into one event with data by this function. The event
+ * ID comes first and then the slot number that caused it. We report
+ * this as one event to the OS.
+ *
+ */
+static void ibm_handle_events(acpi_handle handle, u32 event, void *context)
+{
+ // FIXME: this may have re-entrancy errors with event being static...
+ u8 detail = event & 0x0f;
+ u8 subevent = event & 0xf0;
+
+ struct notification *note = (struct notification *)context;
+
+ dbg("%s: Received notification %02x\n", __FUNCTION__, event);
+
+ if (subevent == 0x80) {
+ dbg("%s: generationg bus event\n", __FUNCTION__);
+ acpi_bus_generate_event(note->device, note->event, detail);
+ } else
+ note->event = event;
+}
+
+/*
+ * ibm_get_table_from_acpi - reads the APLS buffer from ACPI
+ *
+ * this method reads the APLS buffer in from ACPI and
+ * stores the "stripped" table into a single buffer
+ * it allocates and passes the address back in bufp
+ *
+ * if NULL is passed in as buffer, this method only calculates
+ * the size of the table and returns that without filling
+ * in the buffer
+ *
+ * returns < 0 on error or the size of the table on success
+ */
+static int ibm_get_table_from_acpi(char **bufp)
+{
+ union acpi_object *package;
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+ acpi_status status;
+ char *lbuf = NULL;
+ int i, size = -1;
+
+ status = acpi_evaluate_object(ibm_acpi_handle, "APCI", NULL, &buffer);
+ if (ACPI_FAILURE(status)) {
+ err("%s: APCI evaluation failed\n", __FUNCTION__);
+ return -ENODEV;
+ }
+
+ package = (union acpi_object *) buffer.pointer;
+ if(!(package) ||
+ (package->type != ACPI_TYPE_PACKAGE) ||
+ !(package->package.elements)) {
+ err("%s: Invalid APCI object\n", __FUNCTION__);
+ goto read_table_done;
+ }
+
+ for(size = 0, i = 0; i < package->package.count; i++) {
+ if (package->package.elements[i].type != ACPI_TYPE_BUFFER) {
+ err("%s: Invalid APCI element %d\n", __FUNCTION__, i);
+ goto read_table_done;
+ }
+ size += package->package.elements[i].buffer.length;
+ }
+
+ if (bufp == NULL)
+ goto read_table_done;
+
+ lbuf = kmalloc(size, GFP_KERNEL);
+ dbg("%s: element count: %i, ASL table size: %i, &table = 0x%x\n",
+ __FUNCTION__, package->package.count, size, (int)lbuf);
+
+ if (lbuf) {
+ *bufp = lbuf;
+ memset(lbuf, 0, size);
+ } else {
+ size = -ENOMEM;
+ goto read_table_done;
+ }
+
+ size = 0;
+ for (i=0; i<package->package.count; i++) {
+ memcpy(&lbuf[size],
+ package->package.elements[i].buffer.pointer,
+ package->package.elements[i].buffer.length);
+ size += package->package.elements[i].buffer.length;
+ }
+
+read_table_done:
+ kfree(buffer.pointer);
+ return size;
+}
+
+
+/* ibm_find_acpi_device - callback to find our ACPI device
+ *
+ * used as a callback when calling acpi_walk_namespace
+ * to find our device. When this method returns non-zero
+ * acpi_walk_namespace quits its search and returns our value
+ */
+static acpi_status __init ibm_find_acpi_device(acpi_handle handle,
+ u32 lvl, void *context, void **rv)
+{
+ acpi_handle *phandle = (acpi_handle *)context;
+ acpi_status status;
+ struct acpi_device_info info;
+ struct acpi_buffer info_buffer = {
+ .length = sizeof(struct acpi_device_info),
+ .pointer = &info,
+ };
+
+ status = acpi_get_object_info(handle, &info_buffer);
+ if (ACPI_FAILURE(status)) {
+ err("%s: Failed to get device information", __FUNCTION__);
+ return 0;
+ }
+ info.hardware_id.value[sizeof(info.hardware_id.value) - 1] = '\0';
+
+ if(info.current_status && (info.valid & ACPI_VALID_HID) &&
+ (!strcmp(info.hardware_id.value, IBM_HARDWARE_ID1) ||
+ !strcmp(info.hardware_id.value, IBM_HARDWARE_ID2))) {
+ dbg("found hardware: %s, handle: %x\n", info.hardware_id.value,
+ (unsigned int)handle);
+ *phandle = handle;
+ /* returning non-zero causes the search to stop
+ * and returns this value to the caller of
+ * acpi_walk_namespace, but it also causes some warnings
+ * in the acpi debug code to print...
+ */
+ return FOUND_APCI;
+ }
+ return 0;
+}
+
+static int __init ibm_acpiphp_init(void)
+{
+ int retval = 0;
+ acpi_status status;
+ struct acpi_device *device;
+
+ dbg("%s\n", __FUNCTION__);
+
+ if (acpi_walk_namespace(ACPI_TYPE_DEVICE, ACPI_ROOT_OBJECT,
+ ACPI_UINT32_MAX, ibm_find_acpi_device,
+ &ibm_acpi_handle, NULL) != FOUND_APCI) {
+ err("%s: acpi_walk_namespace failed\n", __FUNCTION__);
+ retval = -ENODEV;
+ goto init_return;
+ }
+ dbg("%s: found IBM aPCI device\n", __FUNCTION__);
+ if (acpi_bus_get_device(ibm_acpi_handle, &device)) {
+ err("%s: acpi_bus_get_device failed\n", __FUNCTION__);
+ retval = -ENODEV;
+ goto init_return;
+ }
+ if (acpiphp_register_attention_info(&ibm_attention_info))
+ retval = -ENODEV;
+ goto init_return;
+
+ ibm_note.device = device;
+ status = acpi_install_notify_handler(
+ ibm_acpi_handle,
+ ACPI_DEVICE_NOTIFY,
+ ibm_handle_events,
+ (void *)&ibm_note);
+ if (ACPI_FAILURE(status))
+ {
+ err("%s: Failed to register notification handler\n",
+ __FUNCTION__);
+ retval = -EBUSY;
+ goto init_cleanup;
+ }
+
+ return retval;
+
+init_cleanup:
+ acpiphp_unregister_attention_info(&ibm_attention_info);
+init_return:
+ return retval;
+}
+
+static void __exit ibm_acpiphp_exit(void)
+{
+ acpi_status status;
+
+ dbg("%s\n", __FUNCTION__);
+
+ if (acpiphp_unregister_attention_info(&ibm_attention_info))
+ err("%s: attention info deregistration failed", __FUNCTION__);
+
+ status = acpi_remove_notify_handler(
+ ibm_acpi_handle,
+ ACPI_DEVICE_NOTIFY,
+ ibm_handle_events);
+ if (ACPI_FAILURE(status))
+ err("%s: Notification handler removal failed\n",
+ __FUNCTION__);
+}
+
+module_init(ibm_acpiphp_init);
+module_exit(ibm_acpiphp_exit);
+
+

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:04    [from the cache]
©2003-2011 Jasper Spaans