lkml.org 
[lkml]   [2004]   [Jun]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 2/4]Diskdump Update
This is a patch for scsi common layer.


diff -Nur linux-2.6.6.org/drivers/scsi/Kconfig linux-2.6.6/drivers/scsi/Kconfig
--- linux-2.6.6.org/drivers/scsi/Kconfig 2004-05-10 11:33:19.000000000 +0900
+++ linux-2.6.6/drivers/scsi/Kconfig 2004-06-09 22:24:30.590629105 +0900
@@ -55,6 +55,12 @@
In this case, do not compile the driver for your SCSI host adapter
(below) as a module either.

+config SCSI_DUMP
+ tristate "SCSI dump support"
+ depends on DISKDUMP && SCSI
+ help
+ SCSI dump support
+
config CHR_DEV_ST
tristate "SCSI tape support"
depends on SCSI
diff -Nur linux-2.6.6.org/drivers/scsi/Makefile linux-2.6.6/drivers/scsi/Makefile
--- linux-2.6.6.org/drivers/scsi/Makefile 2004-05-10 11:33:13.000000000 +0900
+++ linux-2.6.6/drivers/scsi/Makefile 2004-06-09 22:24:30.591605668 +0900
@@ -133,6 +133,8 @@
obj-$(CONFIG_BLK_DEV_SR) += sr_mod.o
obj-$(CONFIG_CHR_DEV_SG) += sg.o

+obj-$(CONFIG_SCSI_DUMP) += scsi_dump.o
+
scsi_mod-y += scsi.o hosts.o scsi_ioctl.o constants.o \
scsicam.o scsi_error.o scsi_lib.o \
scsi_scan.o scsi_syms.o scsi_sysfs.o \
diff -Nur linux-2.6.6.org/drivers/scsi/scsi.c linux-2.6.6/drivers/scsi/scsi.c
--- linux-2.6.6.org/drivers/scsi/scsi.c 2004-05-10 11:32:37.000000000 +0900
+++ linux-2.6.6/drivers/scsi/scsi.c 2004-06-09 22:24:30.592582230 +0900
@@ -691,6 +691,9 @@
{
unsigned long flags;

+ if (crashdump_mode())
+ return;
+
/*
* We don't have to worry about this one timing out any more.
* If we are unable to remove the timer, then the command
diff -Nur linux-2.6.6.org/drivers/scsi/scsi_dump.c linux-2.6.6/drivers/scsi/scsi_dump.c
--- linux-2.6.6.org/drivers/scsi/scsi_dump.c 1970-01-01 09:00:00.000000000 +0900
+++ linux-2.6.6/drivers/scsi/scsi_dump.c 2004-06-09 22:31:51.418748705 +0900
@@ -0,0 +1,574 @@
+/*
+ * linux/drivers/scsi/scsi_dump.c
+ *
+ * Copyright (C) 2004 FUJITSU LIMITED
+ * Written by Nobuhiro Tachino (ntachino@jp.fujitsu.com)
+ *
+ * Some codes are derived from drivers/scsi/sd.c
+ */
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#include <linux/module.h>
+
+#include <linux/fs.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+
+#include <linux/blkdev.h>
+#include <linux/blkpg.h>
+
+#include <linux/genhd.h>
+#include <linux/utsname.h>
+#include <linux/crc32.h>
+#include <linux/diskdump.h>
+#include <linux/diskdumplib.h>
+#include <linux/delay.h>
+
+#include <scsi/scsi.h>
+#include <scsi/scsi_ioctl.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_dump.h>
+
+#include "scsi.h"
+#include "scsi_priv.h"
+
+#define MAX_RETRIES 5
+#define SD_TIMEOUT (60 * HZ)
+
+#define Dbg(x, ...) pr_debug("scsi_dump: " x "\n", ## __VA_ARGS__)
+#define Err(x, ...) pr_err ("scsi_dump: " x "\n", ## __VA_ARGS__)
+#define Warn(x, ...) pr_warn ("scsi_dump: " x "\n", ## __VA_ARGS__)
+#define Info(x, ...) pr_info ("scsi_dump: " x "\n", ## __VA_ARGS__)
+
+/* blocks to 512byte sectors */
+#define BLOCK_SECTOR(s) ((s) << (DUMP_BLOCK_SHIFT - 9))
+
+static int quiesce_ok = 0;
+static struct scsi_cmnd scsi_dump_cmnd;
+static struct request scsi_dump_req;
+static uint32_t module_crc;
+
+static void rw_intr(struct scsi_cmnd * scmd)
+{
+ scmd->done = NULL;
+}
+
+/*
+ * Common code to make Scsi_Cmnd
+ */
+static void init_scsi_command(struct scsi_device *sdev, struct scsi_cmnd *scmd,
+ void *buf, int len, unsigned char direction,
+ int set_lun)
+{
+ scmd->request = &scsi_dump_req;
+ scmd->sc_magic = SCSI_CMND_MAGIC;
+ scmd->owner = SCSI_OWNER_MIDLEVEL;
+ scmd->device = sdev;
+ scmd->buffer = scmd->request_buffer = buf;
+ scmd->bufflen = scmd->request_bufflen = len;
+
+
+ scmd->sc_data_direction = direction;
+
+ memcpy(scmd->data_cmnd, scmd->cmnd, sizeof(scmd->cmnd));
+ scmd->cmd_len = COMMAND_SIZE(scmd->cmnd[0]);
+ scmd->old_cmd_len = scmd->cmd_len;
+
+
+ if (set_lun)
+ scmd->cmnd[1] |= (sdev->scsi_level <= SCSI_2) ?
+ ((sdev->lun << 5) & 0xe0) : 0;
+
+ scmd->transfersize = sdev->sector_size;
+ if (direction == SCSI_DATA_WRITE)
+ scmd->underflow = len;
+
+ scmd->allowed = MAX_RETRIES;
+ scmd->timeout_per_command = SD_TIMEOUT;
+
+ /*
+ * This is the completion routine we use. This is matched in terms
+ * of capability to this function.
+ */
+ scmd->done = rw_intr;
+}
+
+static void init_mode_sense_command(struct scsi_device *sdev,
+ struct scsi_cmnd *scmd, void *buf)
+{
+ memset(scmd, 0, sizeof(*scmd));
+ scmd->cmnd[0] = MODE_SENSE;
+ scmd->cmnd[1] = 0x00; /* DBD=0 */
+ scmd->cmnd[2] = 0x08; /* PCF=0 Page 8(Cache) */
+ scmd->cmnd[4] = 255;
+
+ init_scsi_command(sdev, scmd, buf, 256, SCSI_DATA_READ, 1);
+}
+
+static void init_mode_select_command(struct scsi_device *sdev,
+ struct scsi_cmnd *scmd, void *buf, int len)
+{
+ memset(scmd, 0, sizeof(*scmd));
+ scmd->cmnd[0] = MODE_SELECT;
+ scmd->cmnd[1] = 0x10; /* PF=1 SP=0 */
+ scmd->cmnd[4] = len;
+
+ init_scsi_command(sdev, scmd, buf, len, SCSI_DATA_WRITE, 1);
+}
+
+static void init_sync_command(struct scsi_device *sdev, struct scsi_cmnd * scmd)
+{
+ memset(scmd, 0, sizeof(*scmd));
+ scmd->cmnd[0] = SYNCHRONIZE_CACHE;
+
+ init_scsi_command(sdev, scmd, NULL, 0, SCSI_DATA_NONE, 0);
+}
+
+static void init_sense_command(struct scsi_device *sdev, struct scsi_cmnd *scmd,
+ void *buf)
+{
+ memset(scmd, 0, sizeof(*scmd));
+ scmd->cmnd[0] = REQUEST_SENSE;
+ scmd->cmnd[4] = 255;
+
+ init_scsi_command(sdev, scmd, buf, 256, SCSI_DATA_READ, 1);
+}
+
+static int init_rw_command(struct disk_dump_partition *dump_part,
+ struct scsi_device *sdev, struct scsi_cmnd * scmd,
+ int rw, int block, void *buf, unsigned int len)
+{
+ int this_count = len >> 9;
+
+ memset(scmd, 0, sizeof(*scmd));
+
+ if (block + this_count > dump_part->nr_sects) {
+ Err("block number %d is larger than %lu",
+ block + this_count, dump_part->nr_sects);
+ return -EFBIG;
+ }
+
+ block += dump_part->start_sect;
+
+ /*
+ * If we have a 1K hardware sectorsize, prevent access to single
+ * 512 byte sectors. In theory we could handle this - in fact
+ * the scsi cdrom driver must be able to handle this because
+ * we typically use 1K blocksizes, and cdroms typically have
+ * 2K hardware sectorsizes. Of course, things are simpler
+ * with the cdrom, since it is read-only. For performance
+ * reasons, the filesystems should be able to handle this
+ * and not force the scsi disk driver to use bounce buffers
+ * for this.
+ */
+ if (sdev->sector_size == 1024) {
+ block = block >> 1;
+ this_count = this_count >> 1;
+ }
+ if (sdev->sector_size == 2048) {
+ block = block >> 2;
+ this_count = this_count >> 2;
+ }
+ if (sdev->sector_size == 4096) {
+ block = block >> 3;
+ this_count = this_count >> 3;
+ }
+ switch (rw) {
+ case WRITE:
+ if (!sdev->writeable) {
+ Err("writable media");
+ return 0;
+ }
+ scmd->cmnd[0] = WRITE_10;
+ break;
+ case READ:
+ scmd->cmnd[0] = READ_10;
+ break;
+ default:
+ Err("Unknown command %d", rw);
+ return -EINVAL;
+ }
+
+ if (this_count > 0xffff)
+ this_count = 0xffff;
+
+ scmd->cmnd[2] = (unsigned char) (block >> 24) & 0xff;
+ scmd->cmnd[3] = (unsigned char) (block >> 16) & 0xff;
+ scmd->cmnd[4] = (unsigned char) (block >> 8) & 0xff;
+ scmd->cmnd[5] = (unsigned char) block & 0xff;
+ scmd->cmnd[7] = (unsigned char) (this_count >> 8) & 0xff;
+ scmd->cmnd[8] = (unsigned char) this_count & 0xff;
+
+ init_scsi_command(sdev, scmd, buf, len,
+ (rw == WRITE ? SCSI_DATA_WRITE : SCSI_DATA_READ), 1);
+ return 0;
+}
+
+/*
+ * Check the status of scsi command and determine whether it is
+ * success, fail, or retriable.
+ *
+ * Return code
+ * > 0: should retry
+ * = 0: success
+ * < 0: fail
+ */
+static int cmd_result(struct scsi_cmnd *scmd)
+{
+ int status;
+
+ status = status_byte(scmd->result);
+
+ switch (scsi_decide_disposition(scmd)) {
+ case FAILED:
+ break;
+ case NEEDS_RETRY:
+ case ADD_TO_MLQUEUE:
+ return 1 /* retry */;
+ case SUCCESS:
+ if (host_byte(scmd->result) != DID_OK)
+ break;
+
+ if (status == GOOD || status == INTERMEDIATE_GOOD
+ || status == INTERMEDIATE_C_GOOD)
+ return 0;
+ if (status == CHECK_CONDITION &&
+ scmd->sense_buffer[2] == RECOVERED_ERROR)
+ return 0;
+ break;
+ default:
+ Err("bad disposition: %d", scmd->result);
+ return -EIO;
+ }
+
+ Err("command %x failed with 0x%x", scmd->cmnd[0], scmd->result);
+ return -EIO;
+}
+
+static int send_command(struct scsi_cmnd *scmd)
+{
+ struct Scsi_Host *host = scmd->device->host;
+ struct scsi_device *sdev = scmd->device;
+ int ret;
+
+ do {
+ if (!scsi_device_online(sdev)) {
+ Err("Scsi disk is not online");
+ return -EIO;
+ }
+ if (sdev->changed) {
+ Err("SCSI disk has been changed. Prohibiting further I/O");
+ return -EIO;
+ }
+
+ spin_lock(host->host_lock);
+ host->hostt->queuecommand(scmd, rw_intr);
+ spin_unlock(host->host_lock);
+
+ while (scmd->done != NULL) {
+ host->hostt->dump_ops->poll(scmd->device);
+ udelay(100);
+ diskdump_update();
+ }
+ scmd->done = rw_intr;
+ } while ((ret = cmd_result(scmd)) > 0);
+
+ return ret;
+}
+
+/*
+ * If Write Cache Enable of disk device is not set, write I/O takes
+ * long long time. So enable WCE temporary and issue SYNCHRONIZE CACHE
+ * after all write I/Os are done, Following system reboot will reset
+ * WCE bit to original value.
+ */
+static void
+enable_write_cache(struct scsi_device *sdev)
+{
+ char buf[256];
+ int ret;
+ int data_len;
+
+ Dbg("enable write cache");
+ memset(buf, 0, 256);
+
+ init_mode_sense_command(sdev, &scsi_dump_cmnd, buf);
+ if ((ret = send_command(&scsi_dump_cmnd)) < 0) {
+ Warn("MODE SENSE failed");
+ return;
+ }
+
+ if (buf[14] & 0x04) /* WCE is already set */
+ return;
+
+ data_len = buf[0] + 1; /* Data length in mode parameter header */
+ buf[0] = 0;
+ buf[1] = 0;
+ buf[2] = 0;
+ buf[12] &= 0x7f; /* clear PS */
+ buf[14] |= 0x04; /* set WCE */
+
+ init_mode_select_command(sdev, &scsi_dump_cmnd, buf, data_len);
+ if ((ret = send_command(&scsi_dump_cmnd)) < 0) {
+ Warn("MODE SELECT failed");
+
+ init_sense_command(sdev, &scsi_dump_cmnd, buf);
+ if ((ret = send_command(&scsi_dump_cmnd)) < 0) {
+ Err("sense failed");
+ }
+ }
+}
+
+/*
+ * Check whether the dump device is sane enough to handle I/O.
+ *
+ * Return value:
+ * 0: the device is ok
+ * < 0: the device is not ok
+ * > 0: Cannot determine
+ */
+static int
+scsi_dump_sanity_check(struct disk_dump_device *dump_device)
+{
+ struct scsi_device *sdev = dump_device->device;
+ struct Scsi_Host *host = sdev->host;
+ int adapter_sanity = 0;
+ int sanity = 0;
+
+ if (!check_crc_module()) {
+ Err("checksum error. scsi dump module may be compromised.");
+ return -EINVAL;
+ }
+ /*
+ * If host's spinlock is already taken, assume it's part
+ * of crash and skip it.
+ */
+ if (!scsi_device_online(sdev)) {
+ Warn("device not online: host %d channel %d id %d lun %d",
+ host->host_no, sdev->channel, sdev->id, sdev->lun);
+ return -EIO;
+ }
+ if (sdev->changed) {
+ Err("SCSI disk has been changed. Prohibiting further I/O: host %d channel %d id %d lun %d",
+ host->host_no, sdev->channel, sdev->id, sdev->lun);
+ return -EIO;
+ }
+
+ if (host->hostt->dump_ops->sanity_check) {
+ adapter_sanity = host->hostt->dump_ops->sanity_check(sdev);
+ if (adapter_sanity < 0) {
+ Warn("adapter status is not sane");
+ return adapter_sanity;
+ }
+ }
+
+ if (!spin_is_locked(host->host_lock)) {
+ sanity = 0;
+ } else {
+ Warn("host_lock is held: host %d channel %d id %d lun %d",
+ host->host_no, sdev->channel, sdev->id, sdev->lun);
+ return -EIO;
+ }
+ return sanity + adapter_sanity;
+}
+
+/*
+ * Try to reset the host adapter. If the adapter does not have its host reset
+ * handler, try to use its bus device reset handler.
+ */
+static int scsi_dump_reset(struct scsi_device *sdev)
+{
+ struct Scsi_Host *host = sdev->host;
+ struct scsi_host_template *hostt = host->hostt;
+ char buf[256];
+ int ret, i;
+
+ init_sense_command(sdev, &scsi_dump_cmnd, buf);
+
+ if (hostt->eh_host_reset_handler) {
+ spin_lock(host->host_lock);
+ ret = hostt->eh_host_reset_handler(&scsi_dump_cmnd);
+ } else if (hostt->eh_bus_reset_handler) {
+ spin_lock(host->host_lock);
+ ret = hostt->eh_bus_reset_handler(&scsi_dump_cmnd);
+ } else
+ return 0;
+ spin_unlock(host->host_lock);
+
+ if (ret != SUCCESS) {
+ Err("adapter reset failed");
+ return -EIO;
+ }
+
+ /* bus reset settle time. 5sec for old disk devices */
+ for (i = 0; i < 5000; i++) {
+ diskdump_update();
+ mdelay(1);
+ }
+
+ Dbg("request sense");
+ if ((ret = send_command(&scsi_dump_cmnd)) < 0) {
+ Err("sense failed");
+ return -EIO;
+ }
+ return 0;
+}
+
+static int
+scsi_dump_quiesce(struct disk_dump_device *dump_device)
+{
+ struct scsi_device *sdev = dump_device->device;
+ struct Scsi_Host *host = sdev->host;
+ int ret;
+
+ if (host->hostt->dump_ops->quiesce) {
+ ret = host->hostt->dump_ops->quiesce(sdev);
+ if (ret < 0)
+ return ret;
+ }
+
+ Dbg("do bus reset");
+ if ((ret = scsi_dump_reset(sdev)) < 0)
+ return ret;
+
+ if (sdev->scsi_level >= SCSI_2)
+ enable_write_cache(sdev);
+
+ quiesce_ok = 1;
+ return 0;
+}
+
+static int scsi_dump_rw_block(struct disk_dump_partition *dump_part, int rw,
+ unsigned long dump_block_nr, void *buf, int len)
+{
+ struct disk_dump_device *dump_device = dump_part->device;
+ struct scsi_device *sdev = dump_device->device;
+ int block_nr = BLOCK_SECTOR(dump_block_nr);
+ int ret;
+
+ if (!quiesce_ok) {
+ Err("quiesce not called");
+ return -EIO;
+ }
+
+ ret = init_rw_command(dump_part, sdev, &scsi_dump_cmnd, rw,
+ block_nr, buf, DUMP_BLOCK_SIZE * len);
+ if (ret < 0) {
+ Err("init_rw_command failed");
+ return ret;
+ }
+ return send_command(&scsi_dump_cmnd);
+}
+
+static int
+scsi_dump_shutdown(struct disk_dump_device *dump_device)
+{
+ struct scsi_device *sdev = dump_device->device;
+ struct Scsi_Host *host = sdev->host;
+
+ if (sdev->scsi_level >= SCSI_2) {
+ init_sync_command(sdev, &scsi_dump_cmnd);
+ send_command(&scsi_dump_cmnd);
+ }
+
+ if (host->hostt->dump_ops->shutdown)
+ return host->hostt->dump_ops->shutdown(sdev);
+
+ return 0;
+}
+
+static void *scsi_dump_probe(dev_t dev)
+{
+ struct scsi_device *sdev;
+
+ sdev = sd_find_scsi_device(dev);
+ if (sdev == NULL)
+ return NULL;
+ if (!sdev->host->hostt->dump_ops)
+ return NULL;
+
+ return sdev;
+}
+
+
+struct disk_dump_device_ops scsi_dump_device_ops = {
+ .sanity_check = scsi_dump_sanity_check,
+ .rw_block = scsi_dump_rw_block,
+ .quiesce = scsi_dump_quiesce,
+ .shutdown = scsi_dump_shutdown,
+};
+
+static int scsi_dump_add_device(struct disk_dump_device *dump_device)
+{
+ struct scsi_device *sdev;
+ int error;
+
+ sdev = dump_device->device;
+ if (!sdev->host->hostt->dump_ops)
+ return -ENOTSUPP;
+
+ if ((error = scsi_device_get(sdev)) != 0)
+ return error;
+
+ memcpy(&dump_device->ops, &scsi_dump_device_ops,
+ sizeof(scsi_dump_device_ops));
+ if (sdev->host->max_sectors) {
+ dump_device->max_blocks =
+ (sdev->sector_size * sdev->host->max_sectors)
+ >> DUMP_BLOCK_SHIFT;
+ }
+ return 0;
+}
+
+static void scsi_dump_remove_device(struct disk_dump_device *dump_device)
+{
+ struct scsi_device *sdev = dump_device->device;
+
+ scsi_device_put(sdev);
+}
+
+static struct disk_dump_type scsi_dump_type = {
+ .probe = scsi_dump_probe,
+ .add_device = scsi_dump_add_device,
+ .remove_device = scsi_dump_remove_device,
+ .owner = THIS_MODULE,
+};
+
+static int init_scsi_dump(void)
+{
+ int ret;
+
+ if ((ret = register_disk_dump_type(&scsi_dump_type)) < 0) {
+ Err("register failed");
+ return ret;
+ }
+ set_crc_modules();
+ return ret;
+}
+
+static void cleanup_scsi_dump(void)
+{
+ if (unregister_disk_dump_type(&scsi_dump_type) < 0)
+ Err("register failed");
+}
+
+module_init(init_scsi_dump);
+module_exit(cleanup_scsi_dump);
+MODULE_LICENSE("GPL");
diff -Nur linux-2.6.6.org/drivers/scsi/scsi_error.c linux-2.6.6/drivers/scsi/scsi_error.c
--- linux-2.6.6.org/drivers/scsi/scsi_error.c 2004-05-10 11:31:58.000000000 +0900
+++ linux-2.6.6/drivers/scsi/scsi_error.c 2004-06-09 22:24:30.595511918 +0900
@@ -402,6 +402,9 @@
**/
static void scsi_eh_done(struct scsi_cmnd *scmd)
{
+ if (crashdump_mode())
+ return;
+
/*
* if the timeout handler is already running, then just set the
* flag which says we finished late, and return. we have no
diff -Nur linux-2.6.6.org/drivers/scsi/scsi_syms.c linux-2.6.6/drivers/scsi/scsi_syms.c
--- linux-2.6.6.org/drivers/scsi/scsi_syms.c 2004-05-10 11:32:37.000000000 +0900
+++ linux-2.6.6/drivers/scsi/scsi_syms.c 2004-06-09 22:24:30.595511918 +0900
@@ -25,6 +25,7 @@
#include "scsi.h"

#include "scsi_logging.h"
+#include "scsi_priv.h"


/*
@@ -107,3 +108,5 @@
*/
EXPORT_SYMBOL(scsi_add_timer);
EXPORT_SYMBOL(scsi_delete_timer);
+
+EXPORT_SYMBOL(scsi_decide_disposition);
diff -Nur linux-2.6.6.org/drivers/scsi/sd.c linux-2.6.6/drivers/scsi/sd.c
--- linux-2.6.6.org/drivers/scsi/sd.c 2004-05-10 11:33:05.000000000 +0900
+++ linux-2.6.6/drivers/scsi/sd.c 2004-06-09 22:24:30.596488480 +0900
@@ -192,6 +192,21 @@
up(&sd_ref_sem);
}

+#if defined(CONFIG_DISKDUMP) || defined(CONFIG_DISKDUMP_MODULE)
+struct scsi_device *sd_find_scsi_device(dev_t dev)
+{
+ struct gendisk *disk;
+ int part;
+ disk = get_gendisk(dev, &part);
+ if(disk && disk->private_data)
+ return scsi_disk(disk)->device;
+ else
+ return NULL;
+}
+
+EXPORT_SYMBOL(sd_find_scsi_device);
+#endif
+
/**
* sd_init_command - build a scsi (read or write) command from
* information in the request structure.
diff -Nur linux-2.6.6.org/include/scsi/scsi_dump.h linux-2.6.6/include/scsi/scsi_dump.h
--- linux-2.6.6.org/include/scsi/scsi_dump.h 1970-01-01 09:00:00.000000000 +0900
+++ linux-2.6.6/include/scsi/scsi_dump.h 2004-06-09 22:24:30.596488480 +0900
@@ -0,0 +1,38 @@
+#ifndef _SCSI_DUMP_H
+#define _SCSI_DUMP_H
+
+/*
+ * linux/include/scsi/scsi_dump.h
+ *
+ * Copyright (C) 2004 FUJITSU LIMITED
+ * Written by Nobuhiro Tachino (ntachino@jp.fujitsu.com)
+ *
+ */
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+struct scsi_dump_ops {
+ int (*sanity_check)(struct scsi_device *);
+ int (*quiesce)(struct scsi_device *);
+ int (*shutdown)(struct scsi_device *);
+ void (*poll)(struct scsi_device *);
+};
+
+/* sd.c function */
+extern struct scsi_device *sd_find_scsi_device(dev_t);
+
+#endif /* _SCSI_DUMP_H */
diff -Nur linux-2.6.6.org/include/scsi/scsi_host.h linux-2.6.6/include/scsi/scsi_host.h
--- linux-2.6.6.org/include/scsi/scsi_host.h 2004-05-10 11:32:01.000000000 +0900
+++ linux-2.6.6/include/scsi/scsi_host.h 2004-06-09 22:24:30.597465043 +0900
@@ -345,6 +345,11 @@
* module_init/module_exit.
*/
struct list_head legacy_hosts;
+
+ /*
+ * operations for dump
+ */
+ struct scsi_dump_ops *dump_ops;
};

/*
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2005-03-22 14:03    [from the cache]
©2003-2011 Jasper Spaans