lkml.org 
[lkml]   [2004]   [May]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [2.6.7-rc1-mm1] cant mount reiserfs using -o barrier=flush
Hey,

<>Following warnings only come when i mount with the option
barrier=flush, i have never seen them before.
hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hda: drive_cmd: error=0x04 { DriveStatusError }

Also this line clearly states that barrier doesn't work on my harddrive
although it's and IDE drive.
hda: barrier support doesn't work.


Ed Tomlinson wrote:

>Hi
>
>Think this is not just a barrier problem (unless barrier is the default).
>One if my two drives gets the error below during operation.
>The drive is the root drive and is mounted with defaults. 2.6.6-mm4
>was the last kernel booted on this box. The 2.6.7-rc1-mm1 was compiled
>with 2.95 with the following fs options:
>
>CONFIG_EXT2_FS=y
># CONFIG_EXT2_FS_XATTR is not set
>CONFIG_EXT3_FS=m
># CONFIG_EXT3_FS_XATTR is not set
>CONFIG_JBD=m
># CONFIG_JBD_DEBUG is not set
>CONFIG_REISERFS_FS=y
># CONFIG_REISERFS_CHECK is not set
># CONFIG_REISERFS_PROC_INFO is not set
># CONFIG_REISERFS_FS_XATTR is not set
># CONFIG_JFS_FS is not set
># CONFIG_XFS_FS is not set
># CONFIG_MINIX_FS is not set
># CONFIG_ROMFS_FS is not set
># CONFIG_QUOTA is not set
># CONFIG_AUTOFS_FS is not set
>CONFIG_AUTOFS4_FS=m
>
>hda reports:
>root@bert:/usr/src/linux# hdparm -iI /dev/hda
>
>/dev/hda:
>
> Model=WDC AC26400R, FwRev=15.01J15, SerialNo=WD-WM6271600165
> Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
> RawCHS=13328/15/63, TrkSize=57600, SectSize=600, ECCbytes=40
> BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
> CurCHS=13328/15/63, CurSects=12594960, LBA=yes, LBAsects=12594960
> IORDY=on/off, tPIO={min:160,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2 udma3 udma4
> AdvancedPM=no WriteCache=enabled
> Drive conforms to: device does not report version: 1 2 3 4
>
> * signifies the current active mode
>
>
>ATA device, with non-removable media
> Model Number: WDC AC26400R
> Serial Number: WD-WM6271600165
> Firmware Revision: 15.01J15
>Standards:
> Supported: 4 3 2 1
> Likely used: 4
>Configuration:
> Logical max current
> cylinders 13328 13328
> heads 15 15
> sectors/track 63 63
> --
> bytes/track: 57600 bytes/sector: 600
> CHS current addressable sectors: 12594960
> LBA user addressable sectors: 12594960
> device size with M = 1024*1024: 6149 MBytes
> device size with M = 1000*1000: 6448 MBytes (6 GB)
>Capabilities:
> LBA, IORDY(can be disabled)
> Buffer size: 512.0kB bytes avail on r/w long: 40 Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 16
> DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=160ns IORDY flow control=120ns
>Commands/features:
> Enabled Supported:
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Look-ahead
> * Write cache
> * Power Management feature set
> * SMART feature set
>
>root@bert:/usr/src/linux# hdparm -iI /dev/hdb
>
>/dev/hdb:
>
> Model=Maxtor 6E030L0, FwRev=NAR61590, SerialNo=E178CV5E
> Config={ Fixed }
> RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
> BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
> CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=60058656
> IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
> PIO modes: pio0 pio1 pio2 pio3 pio4
> DMA modes: mdma0 mdma1 mdma2
> UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 udma6
> AdvancedPM=yes: disabled (255) WriteCache=enabled
> Drive conforms to: (null):
>
> * signifies the current active mode
>
>
>ATA device, with non-removable media
> Model Number: Maxtor 6E030L0
> Serial Number: E178CV5E
> Firmware Revision: NAR61590
>Standards:
> Supported: 7 6 5 4
> Likely used: 7
>Configuration:
> Logical max current
> cylinders 16383 17475
> heads 16 15
> sectors/track 63 63
> --
> CHS current addressable sectors: 16513875
> LBA user addressable sectors: 60058656
> device size with M = 1024*1024: 29325 MBytes
> device size with M = 1000*1000: 30750 MBytes (30 GB)
>Capabilities:
> LBA, IORDY(can be disabled)
> Queue depth: 1
> Standby timer values: spec'd by Standard, no device specific minimum
> R/W multiple sector transfer: Max = 16 Current = 16
> Advanced power management level: unknown setting (0x0000)
> Recommended acoustic management value: 192, current value: 254
> DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6
> Cycle time: min=120ns recommended=120ns
> PIO: pio0 pio1 pio2 pio3 pio4
> Cycle time: no flow control=120ns IORDY flow control=120ns
>Commands/features:
> Enabled Supported:
> * NOP cmd
> * READ BUFFER cmd
> * WRITE BUFFER cmd
> * Host Protected Area feature set
> * Look-ahead
> * Write cache
> * Power Management feature set
> Security Mode feature set
> * SMART feature set
> * FLUSH CACHE EXT command
> * Mandatory FLUSH CACHE command
> * Device Configuration Overlay feature set
> * Automatic Acoustic Management feature set
> SET MAX security extension
> Advanced Power Management feature set
> * DOWNLOAD MICROCODE cmd
> * SMART self-test
> * SMART error logging
>Security:
> Master password revision code = 65534
> supported
> not enabled
> not locked
> not frozen
> not expired: security count
> not supported: enhanced erase
>HW reset results:
> CBLID- above Vih
> Device num = 1 determined by CSEL
>Checksum: correct
>
>hdb is accessed via dm and evms. This is what the boot of reports:
>
>May 27 18:17:39 bert kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>May 27 18:17:39 bert kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>May 27 18:17:39 bert kernel: PIIX4: IDE controller at PCI slot 0000:00:14.1
>May 27 18:17:39 bert kernel: PIIX4: chipset revision 1
>May 27 18:17:39 bert kernel: PIIX4: not 100%% native mode: will probe irqs later
>May 27 18:17:39 bert kernel: ide0: BM-DMA at 0x10c0-0x10c7, BIOS settings: hda:pio, hdb:DMA
>May 27 18:17:39 bert kernel: ide1: BM-DMA at 0x10c8-0x10cf, BIOS settings: hdc:DMA, hdd:pio
>May 27 18:17:39 bert kernel: hda: WDC AC26400R, ATA DISK drive
>May 27 18:17:39 bert kernel: hdb: Maxtor 6E030L0, ATA DISK drive
>May 27 18:17:39 bert kernel: Using anticipatory io scheduler
>May 27 18:17:39 bert kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>May 27 18:17:39 bert kernel: hdc: HL-DT-ST RW/DVD GCC-4480B, ATAPI CD/DVD-ROM drive
>May 27 18:17:39 bert kernel: ide1 at 0x170-0x177,0x376 on irq 15
>May 27 18:17:39 bert kernel: pnp: the driver 'ide' has been registered
>May 27 18:17:39 bert kernel: hda: max request size: 128KiB
>May 27 18:17:39 bert kernel: hda: 12594960 sectors (6448 MB) w/512KiB Cache, CHS=13328/15/63, UDMA(33)
>May 27 18:17:39 bert kernel: hda: cache flushes supported
>May 27 18:17:39 bert kernel: hda: hda1 hda2 hda3
>May 27 18:17:39 bert kernel: hdb: max request size: 128KiB
>May 27 18:17:39 bert kernel: hdb: 60058656 sectors (30750 MB) w/2048KiB Cache, CHS=59582/16/63, UDMA(33)
>May 27 18:17:39 bert kernel: hdb: cache flushes supported
>May 27 18:17:39 bert kernel: hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 >
>
>followed later by:
>
>May 27 18:18:05 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:18:05 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:18:06 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:18:06 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:19:21 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:19:21 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:19:22 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:19:22 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:20:01 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:20:01 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:20:01 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:20:01 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>May 27 18:21:27 bert kernel: hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>May 27 18:21:27 bert kernel: hda: drive_cmd: error=0x04 { DriveStatusError }
>
>
>
>
>Hope this help,
>
>Ed
>
>On May 27, 2004 04:24 pm, Günther Persoons wrote:
>
>
>>Hey,
>>When i mount my reiser partitie with the option barrier=flush i get
>>following message and error:
>>My harddrive is a 2.5 inch Fujitsu 20GB IDE.
>>
>>mount /dev/hda10 /tmp -o barrier=flush
>>mount: wrong fs type, bad option, bad superblock on /dev/hda10,
>> or too many mounted file systems
>>Log:
>>ReiserFS: hda10: found reiserfs format "3.6" with standard journal
>>ReiserFS: hda10: using ordered data mode
>>reiserfs: using flush barriers
>>ReiserFS: hda10: journal params: device hda10, size 8192, journal first
>>block 18, max trans len 1024, max batch 900, max commit age 30, max
>>trans age 30
>>ReiserFS: hda10: checking transaction log (hda10)
>>hda: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
>>hda: drive_cmd: error=0x04 { DriveStatusError }
>>hda: barrier support doesn't work
>>ReiserFS: hda10: warning: journal-837: IO error during journal replay
>>ReiserFS: hda10: warning: Replay Failure, unable to mount
>>ReiserFS: hda10: warning: sh-2022: reiserfs_fill_super: unable to
>>initialize journal space
>>
>>
>-
>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
>Please read the FAQ at http://www.tux.org/lkml/
>
>
>
>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:03    [W:0.228 / U:0.272 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site