lkml.org 
[lkml]   [2004]   [Mar]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: KERNEL 2.6.3 and MAXTOR 160 GB
Carlo,

From the driver code:


/* Don't use LBA48 on ALi devices before rev 0xC5 */
hwif->no_lba48 = (m5229_revision <= 0xC4) ? 1 : 0;

0xC5 is revision 197 your system has a revision 196 chipset.

The inabilty to use LBA48 with that chipset version is why Linux is saying:

hda: cannot use LBA48 - full capacity 320173056 sectors (163928 MB)
hda: 268435456 sectors (137438 MB) w/7936KiB Cache, CHS=16709/255/63,

and restricting you to use only 137 GB of that drive.

2.6 knows it is a 160GB drive but the chipset can't handle anything
above 137GB.

Cheers,
Dave

Carlo Orecchia wrote:
>
> Sorry my stupid mistake .. this is the correct message from boot:
> Thanks for any reply!!
>
> ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> ALI15X3: IDE controller at PCI slot 0000:00:04.0
> ACPI: No IRQ known for interrupt pin A of device 0000:00:04.0 - using IRQ
> 255
> ALI15X3: chipset revision 196
> ALI15X3: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
> hda: Maxtor 6Y160P0, ATA DISK drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hdc: no response (status = 0xa1), resetting drive
> hdc: no response (status = 0xa1)
> hdd: no response (status = 0xa1), resetting drive
> hdd: no response (status = 0xa1)
> hdc: no response (status = 0xa1), resetting drive
> hdc: no response (status = 0xa1)
> hdd: no response (status = 0xa1), resetting drive
> hdd: no response (status = 0xa1)
> hda: max request size: 128KiB
> hda: cannot use LBA48 - full capacity 320173056 sectors (163928 MB)
> hda: 268435456 sectors (137438 MB) w/7936KiB Cache, CHS=16709/255/63,
> UDMA(100)
> hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
> ide-floppy driver 0.99.newide
> Console: switching to colour frame buffer device 100x37
> mice: PS/2 mouse device common for all mice
> ts: Compaq touchscreen protocol output
> input: PC Speaker
> serio: i8042 AUX port at 0x60,0x64 irq 12
> input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
> serio: i8042 KBD port at 0x60,0x64 irq 1
> input: AT Translated Set 2 keyboard on isa0060/serio0
> Advanced Linux Sound Architecture Driver Version 1.0.2c (Thu Feb 05
> 15:41:49 2004 UTC).
> ALSA device list:
> #0: C-Media PCI CMI8738-MC6 (model 55) at 0xb000, irq 9
> NET: Registered protocol family 2
> IP: routing cache hash table of 8192 buckets, 64Kbytes
> TCP: Hash tables configured (established 262144 bind 65536)
> IPv4 over IPv4 tunneling driver
> GRE over IPv4 tunneling driver
> ip_conntrack version 2.1 (6143 buckets, 49144 max) - 300 bytes per
> conntrack
> ip_tables: (C) 2000-2002 Netfilter core team
> ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.
> http://snowman.net/projects/ipt_recent/
> arp_tables: (C) 2002 David S. Miller
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> NET: Registered protocol family 15
> ACPI: (supports S0 S1 S4 S5)
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 272k freed
> drivers/usb/core/usb.c: registered new driver usbfs
> drivers/usb/core/usb.c: registered new driver hub
> ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> ohci_hcd: block sizes: ed 64 td 64
> ohci_hcd 0000:00:02.0: OHCI Host Controller
> ohci_hcd 0000:00:02.0: irq 9, pci mem f1864000
> ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> ohci_hcd 0000:00:06.0: OHCI Host Controller
> ohci_hcd 0000:00:06.0: irq 9, pci mem f1866000
> ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> drivers/usb/core/usb.c: registered new driver hid
> drivers/usb/input/hid-core.c: v2.0:USB HID core driver
> drivers/usb/core/usb.c: registered new driver usbkbd
> drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
> drivers/usb/core/usb.c: registered new driver usbmouse
>
>
> Here is the .config of kernel (ATA section)
>
> # ATA/ATAPI/MFM/RLL support
> #
> CONFIG_IDE=y
> CONFIG_BLK_DEV_IDE=y
>
> #
> # Please see Documentation/ide.txt for help/info on IDE drives
> #
> # CONFIG_BLK_DEV_HD_IDE is not set
> CONFIG_BLK_DEV_IDEDISK=y
> CONFIG_IDEDISK_MULTI_MODE=y
> CONFIG_IDEDISK_STROKE=y
> CONFIG_BLK_DEV_IDECD=y
> # CONFIG_BLK_DEV_IDETAPE is not set
> CONFIG_BLK_DEV_IDEFLOPPY=y
> CONFIG_BLK_DEV_IDESCSI=y
> # CONFIG_IDE_TASK_IOCTL is not set
> # CONFIG_IDE_TASKFILE_IO is not set
>
> #
> # IDE chipset support/bugfixes
> #
> CONFIG_IDE_GENERIC=y
> CONFIG_BLK_DEV_CMD640=y
> # CONFIG_BLK_DEV_CMD640_ENHANCED is not set
> CONFIG_BLK_DEV_IDEPNP=y
> CONFIG_BLK_DEV_IDEPCI=y
> CONFIG_IDEPCI_SHARE_IRQ=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> CONFIG_BLK_DEV_GENERIC=y
> # CONFIG_BLK_DEV_OPTI621 is not set
> CONFIG_BLK_DEV_RZ1000=y
> CONFIG_BLK_DEV_IDEDMA_PCI=y
> # CONFIG_BLK_DEV_IDEDMA_FORCED is not set
> CONFIG_IDEDMA_PCI_AUTO=y
> # CONFIG_IDEDMA_ONLYDISK is not set
> CONFIG_BLK_DEV_ADMA=y
> CONFIG_BLK_DEV_AEC62XX=y
> CONFIG_BLK_DEV_ALI15X3=y
> # CONFIG_WDC_ALI15X3 is not set
> CONFIG_BLK_DEV_AMD74XX=y
> CONFIG_BLK_DEV_CMD64X=y
> CONFIG_BLK_DEV_TRIFLEX=y
> CONFIG_BLK_DEV_CY82C693=y
> # CONFIG_BLK_DEV_CS5520 is not set
> CONFIG_BLK_DEV_CS5530=y
> CONFIG_BLK_DEV_HPT34X=y
> # CONFIG_HPT34X_AUTODMA is not set
> CONFIG_BLK_DEV_HPT366=y
> CONFIG_BLK_DEV_SC1200=y
> CONFIG_BLK_DEV_PIIX=y
> # CONFIG_BLK_DEV_NS87415 is not set
> CONFIG_BLK_DEV_PDC202XX_OLD=y
> # CONFIG_PDC202XX_BURST is not set
> # CONFIG_BLK_DEV_PDC202XX_NEW is not set
> CONFIG_BLK_DEV_SVWKS=y
> CONFIG_BLK_DEV_SIIMAGE=y
> CONFIG_BLK_DEV_SIS5513=y
> CONFIG_BLK_DEV_SLC90E66=y
> CONFIG_BLK_DEV_TRM290=y
> CONFIG_BLK_DEV_VIA82CXXX=y
> # CONFIG_IDE_CHIPSETS is not set
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_IDEDMA_IVB is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_DMA_NONPCI is not set
> # CONFIG_BLK_DEV_HD is not set
>
>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:01    [W:0.086 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site