Messages in this thread | | | From | Ernst Herzberg <> | Subject | Kernel 2.6.3: tg3: can't set full duplex | Date | Tue, 24 Feb 2004 07:46:58 +0100 |
| |
Moin.
tweaky ~ # dmesg | tail Mounted devfs on /dev Freeing unused kernel memory: 156k freed Adding 2000084k swap on /dev/sda2. Priority:-1 extents:1 kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. tg3: eth0: Link is up at 100 Mbps, half duplex. tg3: eth0: Flow control is off for TX and off for RX. tg3: eth1: Link is up at 1000 Mbps, full duplex. tg3: eth1: Flow control is on for TX and on for RX. tweaky ~ # ethtool eth0 Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Half Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: yes tweaky ~ # ethtool -s eth0 duplex full tweaky ~ # ethtool eth0 Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Half Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: yes tweaky ~ # dmesg | tail Mounted devfs on /dev Freeing unused kernel memory: 156k freed Adding 2000084k swap on /dev/sda2. Priority:-1 extents:1 kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. tg3: eth0: Link is up at 100 Mbps, half duplex. tg3: eth0: Flow control is off for TX and off for RX. tg3: eth1: Link is up at 1000 Mbps, full duplex. tg3: eth1: Flow control is on for TX and on for RX.
-----------------
Nothings happens. Was working with 2.4.21
-----------------
tweaky ~ # ethtool ethtool version 1.7 [..]
tweaky ~ # lspci 00:00.0 Host bridge: ServerWorks CMIC-HE (rev 22) 00:00.1 Host bridge: ServerWorks CMIC-HE 00:00.2 Host bridge: ServerWorks CMIC-HE 00:00.3 Host bridge: ServerWorks CMIC-HE 00:03.0 SCSI storage controller: Adaptec AIC-7892P U160/m (rev 02) 00:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 00:0f.0 Host bridge: ServerWorks CSB5 South Bridge (rev 93) 00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93) 00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 05) 00:0f.3 ISA bridge: ServerWorks GCLE Host Bridge 00:10.0 Host bridge: ServerWorks CIOB30 (rev 03) 00:10.2 Host bridge: ServerWorks CIOB30 (rev 03) 00:11.0 Host bridge: ServerWorks CIOB30 (rev 03) 00:11.2 Host bridge: ServerWorks CIOB30 (rev 03) 00:12.0 Host bridge: ServerWorks CIOB30 (rev 03) 00:12.2 Host bridge: ServerWorks CIOB30 (rev 03) 03:01.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge 04:00.0 PCI bridge: Intel Corp. 21154 PCI-to-PCI Bridge 04:01.0 SCSI storage controller: QLogic Corp. ISP12160 Dual Channel Ultra3 SCSI Processor (rev 06) 05:00.0 RAID bus controller: American Megatrends Inc. MegaRAID (rev 20) 0a:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5700 Gigabit Ethernet (rev 14) 0a:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5700 Gigabit Ethernet (rev 14)
---------------------------------
Problem is: With this switch this card hangs sometimes if fullduplex is not switched on. And the port on the Switch supports full duplex ;-)
~Earny - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |