lkml.org 
[lkml]   [2004]   [Dec]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subjectproblems with cx88 driver
Hello,

First of all, thanks Adrian, your cx88 patch works well.
But I have some other problems with the cx88 driver:
My card is sometimes shown as an unknown device and it is also
recognized as a "Hauppauge WinTV 34xxx models" by dmesg and tvtime (the
card is a Hauppauge WinTV-PCI).
The screen stays b/w until I set hue to 0 and saturation to 100 in tvtime.

Here is the output of lspci -vv:
00:0e.0 Multimedia video controller: Conexant: Unknown device 8800 (rev 05)
Subsystem: Hauppauge computer works Inc.: Unknown device 3401
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 13750ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0e.1 Multimedia controller: Conexant: Unknown device 8811 (rev 05)
Subsystem: Hauppauge computer works Inc.: Unknown device 3401
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at eb000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

dmesg:
[...]
Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.4 loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 10 (level, low) -> IRQ 10
cx88[0]: subsystem: 0070:3401, board: Hauppauge WinTV 34xxx models
[card=1,autodetected]
cx88[0]: hauppauge eeprom: model=34514, tuner=LG TPI8PSB01D (28), radio=yes
cx88[0]/0: found at 0000:00:0e.0, rev: 5, irq: 10, latency: 32, mmio:
0xec000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
cx88[0]/0: set_audio_standard_BTSC (status: known-good)
cx2388x blackbird driver version 0.0.4 loaded
cx88[0]/0: cx88: tvaudio thread started
cx88[0]/0: AUD_STATUS: 0x22 [mono/no pilot] ctl=BTSC_AUTO_STEREO
tuner: chip found at addr 0xc2 i2c-bus cx88[0]
tuner: type set to 28 (LG PAL_BG+FM (TPI8PSB01D)) by cx88[0]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
[...]
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5176 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b6 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x513a [mono/pilot c2] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5132 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x517a [mono/pilot c2] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5176 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51ba [mono/pilot c2] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5176 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51f6 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51f2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x517a [mono/pilot c2] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5176 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x513a [mono/pilot c2] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x50f6 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5132 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5136 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5176 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x5172 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51f2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51ba [mono/pilot c2] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b6 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51f6 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b6 [mono/pilot c1] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51f2 [mono/no pilot] ctl=A2_FORCE_MONO1
cx88[0]/0: AUD_STATUS: 0x51b2 [mono/no pilot] ctl=A2_FORCE_MONO1
[...and many lines similar to those before]

Any suggestions?
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:09    [W:0.060 / U:0.356 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site