[lkml]   [2004]   [Nov]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
    SubjectRe: 2.6.10-rc2 doesn't boot (if no floppy device)
    On Fri, Nov 19, 2004 at 09:36:12AM -0800, Linus Torvalds wrote:
    > On Fri, 19 Nov 2004, Adrian Bunk wrote:
    > >
    > > It's not a problem (I just wasn't sure, whether enabling APIC might
    > > change something relevant.
    > It did. You no longer show the problem. No irq storm.
    > So can you disable APIC again, and just remove the non-relevant APIC print
    > calls to get it to compile?

    dmesg is below.

    > Linus


    Linux version 2.6.10-rc2 ( (gcc version 3.4.2 (Debian 3.4.2-3)) #16 Fri Nov 19 19:40:36 CET 2004
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
    BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
    BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
    BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
    255MB LOWMEM available.
    On node 0 totalpages: 65520
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 61424 pages, LIFO batch:14
    HighMem zone: 0 pages, LIFO batch:1
    DMI 2.3 present.
    ACPI: RSDP (v000 AMI ) @ 0x000fab70
    ACPI: RSDT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff0000
    ACPI: FADT (v001 AMIINT SiS740XX 0x00000011 MSFT 0x0100000b) @ 0x0fff0030
    ACPI: MADT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff00c0
    ACPI: DSDT (v001 SiS 746 0x00000100 MSFT 0x0100000d) @ 0x00000000
    Built 1 zonelists
    Kernel command line: BOOT_IMAGE=test ro root=301 mode=1280x1024@760 apic=debug acpi_dbg_level=1
    Initializing CPU#0
    CPU 0 irqstacks, hard=c0466000 soft=c0465000
    PID hash table entries: 1024 (order: 10, 16384 bytes)
    Detected 1800.276 MHz processor.
    Using tsc for high-res timesource
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    Memory: 255340k/262080k available (2364k kernel code, 6172k reserved, 943k data, 144k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay loop... 3563.52 BogoMIPS (lpj=1781760)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
    CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 256K (64 bytes/line)
    CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
    CPU: AMD Athlon(tm) XP 2200+ stepping 01
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ACPI: IRQ9 SCI: Edge set to Level Trigger.
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20041105
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    Uncovering SIS963 that hid as a SIS503 (compatible=0)
    Enabling SiS 96x SMBus.
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: Power Resource [URP1] (off)
    ACPI: Power Resource [URP2] (off)
    ACPI: Power Resource [FDDP] (off)
    ACPI: Power Resource [LPTP] (off)
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    SCSI subsystem initialized
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    PCI: Using ACPI for IRQ routing
    ** PCI interrupts are no longer routed automatically. If this
    ** causes a device to stop working, it is probably because the
    ** driver failed to call pci_enable_device(). As a temporary
    ** workaround, the "pci=routeirq" argument restores the old
    ** behavior. If this argument makes the device work again,
    ** please email the output of "lspci" to
    ** so I can fix the driver.
    NTFS driver 2.1.22 [Flags: R/O].
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    radeonfb: Found Intel x86 BIOS ROM Image
    radeonfb: Retreived PLL infos from BIOS
    radeonfb: Reference=27.00 MHz (RefDiv=60) Memory=155.00 Mhz, System=155.00 MHz
    radeonfb: PLL min 12000 max 35000
    radeonfb: Monitor 1 type DFP found
    radeonfb: EDID probed
    radeonfb: Monitor 2 type no found
    Console: switching to colour frame buffer device 160x64
    radeonfb: ATI Radeon QY DDR SGRAM 64 MB
    lp: driver loaded but no devices found
    Real Time Clock Driver v1.12
    Non-volatile memory driver v1.2
    Linux agpgart interface v0.100 (c) Dave Jones
    agpgart: Detected SiS 746 chipset
    agpgart: Maximum main memory to use for agp memory: 203M
    agpgart: AGP aperture is 64M @ 0xd0000000
    ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
    parport0: irq 7 detected
    lp0: using parport0 (polling).
    io scheduler noop registered
    io scheduler cfq registered
    elevator: using cfq as default io scheduler
    irq 6: nobody cared!
    [<c012c0d4>] __report_bad_irq+0x24/0x80
    [<c012c1e1>] note_interrupt+0x81/0xa0
    [<c012bc13>] __do_IRQ+0x143/0x170
    [<c01040ce>] do_IRQ+0x3e/0x60
    [<c010271a>] common_interrupt+0x1a/0x20
    [<c0116720>] __do_softirq+0x30/0x90
    [<c01041d1>] do_softirq+0x41/0x50
    [<c012ba55>] irq_exit+0x35/0x40
    [<c01040d5>] do_IRQ+0x45/0x60
    [<c010271a>] common_interrupt+0x1a/0x20
    [<c012be74>] setup_irq+0x94/0x110
    [<c0258300>] floppy_hardint+0x0/0x120
    [<c012c07c>] request_irq+0x7c/0xb0
    [<c02584df>] fd_request_irq+0x2f/0x60
    [<c025edab>] floppy_grab_irq_and_dma+0x4b/0x3b0
    [<c044ec5c>] floppy_init+0x1ec/0x5b0
    [<c025ece0>] floppy_find+0x0/0x80
    [<c043c813>] do_initcalls+0x53/0xb0
    [<c0100400>] init+0x0/0x110
    [<c0100400>] init+0x0/0x110
    [<c010042a>] init+0x2a/0x110
    [<c0100818>] kernel_thread_helper+0x0/0x18
    [<c010081d>] kernel_thread_helper+0x5/0x18
    [<c0258300>] (floppy_hardint+0x0/0x120)
    Disabling IRQ #6
    floppy0: no floppy controllers found
    loop: loaded (max 8 devices)
    sis900.c: v1.08.07 11/02/2003
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
    PCI: setting IRQ 6 as level-triggered
    ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 6 (level, low) -> IRQ 6
    eth0: Realtek RTL8201 PHY transceiver found at address 1.
    eth0: Using transceiver found at address 1 as default
    eth0: SiS 900 PCI Fast Ethernet at 0xdc00, IRQ 6, 00:00:00:00:00:00.
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    SIS5513: IDE controller at PCI slot 0000:00:02.5
    SIS5513: chipset revision 0
    SIS5513: not 100% native mode: will probe irqs later
    SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
    Probing IDE interface ide0...
    hda: SAMSUNG SV1604N, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: LITE-ON LTR-12101B, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: max request size: 1024KiB
    hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
    hda: cache flushes supported
    hda: hda1 hda2 hda3 hda4
    hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
    Uniform CD-ROM driver Revision: 3.20
    ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
    PCI: setting IRQ 10 as level-triggered
    ACPI: PCI interrupt 0000:00:03.2[D] -> GSI 10 (level, low) -> IRQ 10
    ehci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 2.0 Controller
    ehci_hcd 0000:00:03.2: irq 10, pci mem 0xcffff000
    ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
    PCI: cache line size of 64 is not supported by device 0000:00:03.2
    ehci_hcd 0000:00:03.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    Initializing USB Mass Storage driver...
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard on isa0060/serio0
    input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
    i2c /dev entries driver
    Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 15 07:17:53 2004 UTC).
    ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 11 (level, low) -> IRQ 11
    ALSA device list:
    #0: Ensoniq AudioPCI ENS1371 at 0xd800, irq 11
    NET: Registered protocol family 2
    IP: routing cache hash table of 2048 buckets, 16Kbytes
    TCP: Hash tables configured (established 16384 bind 32768)
    ip_conntrack version 2.1 (2047 buckets, 16376 max) - 176 bytes per conntrack
    ip_tables: (C) 2000-2002 Netfilter core team
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
    VFS: Mounted root (ext2 filesystem) readonly.
    Freeing unused kernel memory: 144k freed
    Adding 987988k swap on /dev/hda2. Priority:-1 extents:1
    eth0: Media Link On 10mbps half-duplex
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to
    More majordomo info at
    Please read the FAQ at

     \ /
      Last update: 2005-03-22 14:08    [W:0.034 / U:12.540 seconds]
    ©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site