lkml.org 
[lkml]   [2004]   [Nov]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: 2.6.10-rc1-mm5
    Hi.

    Maciej W. Rozycki wrote:
    >> nmi_watchdog=1 still doesn't work.
    >> Any ideas about this?
    > Interesting -- your local APIC seems to be disabled by the firmware
    > (otherwise it would work even without my fix), so how can an I/O APIC
    > work?
    I don't think it worked. I do not even
    claim there is still some bug to that.
    But I know that nmi_watchdog=1 worked -
    thats for sure. I think there was some
    fallback, which is now either broken or
    disabled intentionally, and that's what
    I wanted to find out to make sure that
    everything works as expected.

    > If you send me the bootstrap log back I may have a look to see what's
    > wrong about the I/O APIC.
    I applied your patch and here are 2 logs -
    one from older kernel, one with -mm5 with
    patch. Both have nmi_watchdog=1, but the
    NMI works only with the old one.
    Does this shed some light?

    Linux version 2.6.10-rc1-mm5 (root@stas) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #6 SMP Tue Nov 16 16:47:03 MSK 2004
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
    BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
    BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
    511MB LOWMEM available.
    On node 0 totalpages: 131056
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 126960 pages, LIFO batch:16
    HighMem zone: 0 pages, LIFO batch:1
    DMI 2.3 present.
    ACPI: RSDP (v000 IntelR ) @ 0x000f75d0
    ACPI: RSDT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
    ACPI: FADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
    ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x4008
    Built 1 zonelists
    Local APIC disabled by BIOS -- reenabling.
    Found and enabled local APIC!
    mapped APIC to ffffd000 (fee00000)
    Initializing CPU#0
    Kernel command line: ro root=/dev/hda12 lapic nmi_watchdog=1 debug apic=debug
    CPU 0 irqstacks, hard=c0428000 soft=c0426000
    PID hash table entries: 2048 (order: 11, 32768 bytes)
    Detected 1133.740 MHz processor.
    Using pmtmr for high-res timesource
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 515200k/524224k available (2141k kernel code, 8536k reserved, 848k data, 208k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay loop... 2244.60 BogoMIPS (lpj=1122304)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
    CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ACPI: IRQ9 SCI: Level Trigger.
    CPU0: Intel(R) Pentium(R) III CPU 1133MHz stepping 01
    per-CPU timeslice cutoff: 731.79 usecs.
    task migration cache decay timeout: 1 msecs.
    SMP motherboard not detected.
    Getting VERSION: 40011
    Getting VERSION: 40011
    Getting ID: 0
    Getting LVT0: 700
    Getting LVT1: 400
    enabled ExtINT on CPU#0
    Using local APIC timer interrupts.
    calibrating APIC timer ...
    ..... CPU clock speed is 1133.0167 MHz.
    ..... host bus clock speed is 133.0313 MHz.
    Brought up 1 CPUs
    CPU0:
    domain 0: span 1
    groups: 1
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xfafc0, last bus=2
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20041105
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
    Linux Plug and Play Support v0.97 (c) Adam Belay
    pnp: PnP ACPI init
    pnp: PnP ACPI: found 12 devices
    PnPBIOS: Disabled by ACPI
    PCI: Using ACPI for IRQ routing
    ** PCI interrupts are no longer routed automatically. If this
    ** causes a device to stop working, it is probably because the
    ** driver failed to call pci_enable_device(). As a temporary
    ** workaround, the "pci=routeirq" argument restores the old
    ** behavior. If this argument makes the device work again,
    ** please email the output of "lspci" to bjorn.helgaas@hp.com
    ** so I can fix the driver.
    fscache: general fs caching registered
    CacheFS: general fs caching v0.1 registered
    Machine check exception polling timer started.
    apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
    apm: overridden by ACPI.
    audit: initializing netlink socket (disabled)
    audit(1100624010.649:0): initialized
    Total HugeTLB memory allocated, 0
    Initializing Cryptographic API
    ACPI: Power Button (FF) [PWRF]
    ACPI: Sleep Button (CM) [SLPB]
    ACPI: Fan [FAN] (on)
    ACPI: Processor [CPU0] (supports C1 C2)
    ACPI: Processor [CPU0] (supports 2 throttling states)
    ACPI: Thermal Zone [THRM] (34 C)
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    lp: driver loaded but no devices found
    Real Time Clock Driver v1.12
    Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
    ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, 0x64, irq 1
    ACPI: PS/2 Mouse Controller [PS2M] at irq 12
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    PCI: setting IRQ 11 as level-triggered
    ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    ttyS4: detected caps 00000700 should be 00000100
    ttyS4 at I/O 0xa000 (irq = 11) is a 16C950/954
    ttyS5: detected caps 00000700 should be 00000100
    ttyS5 at I/O 0xa400 (irq = 11) is a 16C950/954
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    parport: PnPBIOS parport detected.
    parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    lp0: using parport0 (interrupt-driven).
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered
    ACPI: Floppy Controller [FDC0] at I/O 0x3f0-0x3f5, 0x3f7 irq 6 dma channel 2
    elevator: using anticipatory as default io scheduler
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    loop: loaded (max 8 devices)
    nbd: registered device at major 43
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH2: IDE controller at PCI slot 0000:00:1f.1
    ICH2: chipset revision 17
    ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
    Probing IDE interface ide0...
    hda: MAXTOR 6L040J2, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    Probing IDE interface ide2...
    ide2: Wait for ready failed before probe !
    Probing IDE interface ide3...
    ide3: Wait for ready failed before probe !
    Probing IDE interface ide4...
    ide4: Wait for ready failed before probe !
    Probing IDE interface ide5...
    ide5: Wait for ready failed before probe !
    hda: max request size: 128KiB
    hda: 78177792 sectors (40027 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(100)
    hda: cache flushes supported
    hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 >
    hdc: ATAPI 50X CD-ROM drive, 128kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard on isa0060/serio0
    input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
    Please email the following PERFCTR INIT lines to mikpe@csd.uu.se
    To remove this message, rebuild the driver with CONFIG_PERFCTR_INIT_TESTS=n
    PERFCTR INIT: vendor 0, family 6, model 11, stepping 1, clock 1133740 kHz
    PERFCTR INIT: NITER == 64
    PERFCTR INIT: loop overhead is 228 cycles
    PERFCTR INIT: rdtsc cost is 35.2 cycles (2484 total)
    PERFCTR INIT: rdpmc cost is 35.9 cycles (2528 total)
    PERFCTR INIT: rdmsr (counter) cost is 90.3 cycles (6008 total)
    PERFCTR INIT: rdmsr (evntsel) cost is 71.6 cycles (4816 total)
    PERFCTR INIT: wrmsr (counter) cost is 100.6 cycles (6669 total)
    PERFCTR INIT: wrmsr (evntsel) cost is 96.0 cycles (6375 total)
    PERFCTR INIT: read cr4 cost is 1.8 cycles (346 total)
    PERFCTR INIT: write cr4 cost is 42.1 cycles (2928 total)
    PERFCTR INIT: write LVTPC cost is 50.7 cycles (3479 total)
    PERFCTR INIT: sync_core cost is 129.2 cycles (8500 total)
    perfctr: driver 2.7.6, cpu type Intel P6 at 1133740 kHz
    NET: Registered protocol family 2
    IP: routing cache hash table of 2048 buckets, 32Kbytes
    TCP: Hash tables configured (established 16384 bind 16384)
    ip_conntrack version 2.1 (4095 buckets, 32760 max) - 312 bytes per conntrack
    ip_tables: (C) 2000-2002 Netfilter core team
    ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
    arp_tables: (C) 2002 David S. Miller
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    ACPI: (supports S0 S1 S4 S5)
    ACPI wakeup devices:
    SLPB PCI0 HUB0 USB0 USB1 UAR1 UAR2
    BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
    CacheFS: Wrong magic number on cache
    EXT3-fs: mounted filesystem with ordered data mode.
    VFS: Mounted root (ext3 filesystem) readonly.
    Freeing unused kernel memory: 208k freed
    kjournald starting. Commit interval 5 seconds
    ibm_acpi: ec object not found
    thinkpad_acpi: ACPI IBM Thinkpad Fn+Fx key driver version 1.1
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    USB Universal Host Controller Interface driver v2.2
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
    ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    uhci_hcd 0000:00:1f.2: irq 11, io base 0xd000
    uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 15
    PCI: setting IRQ 15 as level-triggered
    ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 15 (level, low) -> IRQ 15
    uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
    PCI: Setting latency timer of device 0000:00:1f.4 to 64
    uhci_hcd 0000:00:1f.4: irq 15, io base 0xd400
    uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
    usb 1-1: new full speed USB device using uhci_hcd and address 2
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    SCSI subsystem initialized
    Initializing USB Mass Storage driver...
    scsi0 : SCSI emulation for USB Mass Storage devices
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb-storage: device found at 2
    usb-storage: waiting for device to settle before scanning
    EXT3 FS on hda12, internal journal
    Adding 530104k swap on /dev/hda5. Priority:-1 extents:1
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda6, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda14, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda3, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda11, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda7, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda10, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda13, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda9, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
    FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
    NTFS driver 2.1.22 [Flags: R/W MODULE].
    NTFS volume version 3.1.
    NTFS-fs error (device hda2): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
    Vendor: JetFlash Model: TS256MJF2A Rev: 1.00
    Type: Direct-Access ANSI SCSI revision: 02
    usb-storage: device scan complete
    SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
    sda: Write Protect is off
    sda: Mode Sense: 0b 00 00 08
    sda: assuming drive cache: write through
    sda: sda1
    Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
    ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
    3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
    0000:02:04.0: 3Com PCI 3c905C Tornado at 0xc000. Vers LK1.1.19
    ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
    NET: Registered protocol family 10
    Disabled Privacy Extensions on device c03b1c00(lo)
    IPv6 over IPv4 tunneling driver
    eth0: no IPv6 routers present
    Linux version 2.6.10-rc1 (root@stas) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 SMP Thu Nov 4 09:39:47 MSK 2004
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
    BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
    BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
    BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
    BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
    0MB HIGHMEM available.
    511MB LOWMEM available.
    On node 0 totalpages: 131056
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 126960 pages, LIFO batch:16
    HighMem zone: 0 pages, LIFO batch:1
    DMI 2.3 present.
    ACPI: RSDP (v000 IntelR ) @ 0x000f75d0
    ACPI: RSDT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
    ACPI: FADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
    ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
    ACPI: PM-Timer IO Port: 0x4008
    Built 1 zonelists
    Kernel command line: ro root=/dev/hda12 lapic nmi_watchdog=1 debug apic=debug
    Local APIC disabled by BIOS -- reenabling.
    Found and enabled local APIC!
    mapped APIC to ffffd000 (fee00000)
    Initializing CPU#0
    CPU 0 irqstacks, hard=c040d000 soft=c040b000
    PID hash table entries: 2048 (order: 11, 32768 bytes)
    Detected 1133.740 MHz processor.
    Using pmtmr for high-res timesource
    Console: colour VGA+ 80x25
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Memory: 515152k/524224k available (2061k kernel code, 8472k reserved, 830k data, 200k init, 0k highmem)
    Checking if this processor honours the WP bit even in supervisor mode... Ok.
    Calibrating delay loop... 2244.60 BogoMIPS (lpj=1122304)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000
    CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 256K
    CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    ACPI: IRQ9 SCI: Level Trigger.
    CPU0: Intel(R) Pentium(R) III CPU 1133MHz stepping 01
    per-CPU timeslice cutoff: 731.79 usecs.
    task migration cache decay timeout: 1 msecs.
    SMP motherboard not detected.
    Getting VERSION: 40011
    Getting VERSION: 40011
    Getting ID: 0
    Getting LVT0: 700
    Getting LVT1: 400
    enabled ExtINT on CPU#0
    testing NMI watchdog ... OK.
    Using local APIC timer interrupts.
    calibrating APIC timer ...
    ..... CPU clock speed is 1133.0175 MHz.
    ..... host bus clock speed is 133.0314 MHz.
    Brought up 1 CPUs
    CPU0:
    domain 0: span 1
    groups: 1
    NET: Registered protocol family 16
    PCI: PCI BIOS revision 2.10 entry at 0xfafc0, last bus=2
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20040816
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    PCI: Transparent bridge - 0000:00:1e.0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
    Linux Plug and Play Support v0.97 (c) Adam Belay
    PnPBIOS: Scanning system for PnP BIOS support...
    PnPBIOS: Found PnP BIOS installation structure at 0xc00fb9a0
    PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb9d0, dseg 0xf0000
    PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
    SCSI subsystem initialized
    PCI: Using ACPI for IRQ routing
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
    ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
    ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
    ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
    ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
    ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI interrupt 0000:02:00.1[A] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
    ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 10 (level, low) -> IRQ 10
    ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
    ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 5 (level, low) -> IRQ 5
    Machine check exception polling timer started.
    apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
    apm: overridden by ACPI.
    audit: initializing netlink socket (disabled)
    audit(1100624518.455:0): initialized
    Total HugeTLB memory allocated, 0
    Initializing Cryptographic API
    ACPI: Power Button (FF) [PWRF]
    ACPI: Sleep Button (CM) [SLPB]
    ACPI: Fan [FAN] (on)
    ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
    ACPI: Thermal Zone [THRM] (34 C)
    isapnp: Scanning for PnP cards...
    isapnp: No Plug & Play device found
    lp: driver loaded but no devices found
    Real Time Clock Driver v1.12
    Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
    serio: i8042 AUX port at 0x60,0x64 irq 12
    serio: i8042 KBD port at 0x60,0x64 irq 1
    Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
    ttyS4: detected caps 00000700 should be 00000100
    ttyS4 at I/O 0xa000 (irq = 11) is a 16C950/954
    ttyS5: detected caps 00000700 should be 00000100
    ttyS5 at I/O 0xa400 (irq = 11) is a 16C950/954
    ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    parport: PnPBIOS parport detected.
    parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
    lp0: using parport0 (interrupt-driven).
    io scheduler noop registered
    io scheduler anticipatory registered
    io scheduler deadline registered
    io scheduler cfq registered
    elevator: using anticipatory as default io scheduler
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a post-1991 82077
    loop: loaded (max 8 devices)
    nbd: registered device at major 43
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    ICH2: IDE controller at PCI slot 0000:00:1f.1
    ICH2: chipset revision 17
    ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
    Probing IDE interface ide0...
    hda: MAXTOR 6L040J2, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    Probing IDE interface ide1...
    hdc: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    Probing IDE interface ide2...
    ide2: Wait for ready failed before probe !
    Probing IDE interface ide3...
    ide3: Wait for ready failed before probe !
    Probing IDE interface ide4...
    ide4: Wait for ready failed before probe !
    Probing IDE interface ide5...
    ide5: Wait for ready failed before probe !
    hda: max request size: 128KiB
    hda: 78177792 sectors (40027 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(100)
    hda: cache flushes supported
    hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 >
    hdc: ATAPI 50X CD-ROM drive, 128kB Cache, UDMA(33)
    Uniform CD-ROM driver Revision: 3.20
    libata version 1.02 loaded.
    mice: PS/2 mouse device common for all mice
    input: AT Translated Set 2 keyboard on isa0060/serio0
    input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
    NET: Registered protocol family 2
    IP: routing cache hash table of 2048 buckets, 32Kbytes
    TCP: Hash tables configured (established 16384 bind 21845)
    ip_conntrack version 2.1 (4095 buckets, 32760 max) - 308 bytes per conntrack
    ip_tables: (C) 2000-2002 Netfilter core team
    ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
    arp_tables: (C) 2002 David S. Miller
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    ACPI: (supports S0 S1 S4 S5)
    ACPI wakeup devices:
    SLPB PCI0 HUB0 USB0 USB1 UAR1 UAR2
    BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
    EXT3-fs: mounted filesystem with ordered data mode.
    VFS: Mounted root (ext3 filesystem) readonly.
    Freeing unused kernel memory: 200k freed
    kjournald starting. Commit interval 5 seconds
    usbcore: registered new driver usbfs
    usbcore: registered new driver hub
    USB Universal Host Controller Interface driver v2.2
    ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
    PCI: Setting latency timer of device 0000:00:1f.2 to 64
    uhci_hcd 0000:00:1f.2: irq 11, io base 0xd000
    uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 11 (level, low) -> IRQ 11
    uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
    PCI: Setting latency timer of device 0000:00:1f.4 to 64
    uhci_hcd 0000:00:1f.4: irq 11, io base 0xd400
    uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    usb 1-1: new full speed USB device using address 2
    Initializing USB Mass Storage driver...
    scsi0 : SCSI emulation for USB Mass Storage devices
    usbcore: registered new driver usb-storage
    USB Mass Storage support registered.
    usb-storage: device found at 2
    usb-storage: waiting for device to settle before scanning
    EXT3 FS on hda12, internal journal
    Adding 530104k swap on /dev/hda5. Priority:-1 extents:1
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda6, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda14, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda3, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda11, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda7, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda10, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda13, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on hda9, internal journal
    EXT3-fs: mounted filesystem with ordered data mode.
    FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
    FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
    NTFS driver 2.1.21 [Flags: R/W MODULE].
    NTFS volume version 3.1.
    NTFS-fs error (device hda2): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
    Vendor: JetFlash Model: TS256MJF2A Rev: 1.00
    Type: Direct-Access ANSI SCSI revision: 02
    usb-storage: device scan complete
    ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 11 (level, low) -> IRQ 11
    3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
    0000:02:04.0: 3Com PCI 3c905C Tornado at 0xc000. Vers LK1.1.19
    SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
    sda: Write Protect is off
    sda: Mode Sense: 0b 00 00 08
    sda: assuming drive cache: write through
    sda: sda1
    Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
    NET: Registered protocol family 10
    Disabled Privacy Extensions on device c039c000(lo)
    IPv6 over IPv4 tunneling driver
    eth0: no IPv6 routers present
    \
     
     \ /
      Last update: 2005-03-22 14:08    [W:0.111 / U:3.152 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site