lkml.org 
[lkml]   [2004]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] sungem: Fix stop_phy
From
Date
On Wed, 2004-11-10 at 09:27 +0100, Colin Leroy wrote:
> Hi,
>
> sungem driver's stop_phy differs quite a lot from Darwin's driver:
> In darwin, the hack consisting in reading and writing the same
> from/to MII_LPA is applied to every sungem card, not only bcm5201.
> Also, it is done before the rest of the stuff, not after. Maybe order
> matters.
> In Linux sungem's driver, the BCM5221 phy is suspended as the BCM5201.
> It is (completely) different in darwin.
>
> The patch following this follows OS X a bit more closely. It works on
> iBook G4 with a BCM5221, it would be nice if users of other PHYs could
> test it. If I'm correct, stop_phy is called once during boot (I had an
> oops from it during boot while hacking on it), so booting and checking
> that network works should be enough.

Which version of Darwin did you look at ? There have been changes since
I wrote that code. Note that currently, sungem stops everything (cell,
PHY, ...) when the interface is down for more than 10 seconds, though
I've been thinking about removing that "feature" since it prevents
polling the link...

> Signed-off-by: Colin Leroy <colin@colino.net>
> diff -ur a/drivers/net/sungem.c b/drivers/net/sungem.c
> --- a/drivers/net/sungem.c 2004-10-18 23:55:28.000000000 +0200
> +++ b/drivers/net/sungem.c 2004-11-10 09:16:55.660896544 +0100
> @@ -2124,6 +2124,8 @@
> */
> msleep(10);
>
> + /* FIXME OS X starts with disabling interrupts for BCM5201 */

PHY interrupts are used for WOL afaik

> /* Make sure we aren't polling PHY status change. We
> * don't currently use that feature though
> */

We don't use autopoll as it's somewhat buggy

> @@ -2131,6 +2133,8 @@
> mifcfg &= ~MIF_CFG_POLL;
> writel(mifcfg, gp->regs + MIF_CFG);
>
> + bcm_link_partner_hack(&gp->phy_mii);

I doubt this is useful, and I'd like to avoid those hacks that violate
the layering of sungem vs. sungem_phy.c

If you really want to read the LPA, then do so on all PHYs from
sungem.c. Clearing the interrupts can be done from the PHY init().

> if (gp->wake_on_lan) {
> /* Setup wake-on-lan */
> } else {
> @@ -2159,7 +2163,7 @@
> }
>
> if (found_mii_phy(gp) && gp->phy_mii.def->ops->suspend)
> - gp->phy_mii.def->ops->suspend(&gp->phy_mii, 0 /* wake on lan options */);
> + gp->phy_mii.def->ops->suspend(&gp->phy_mii, gp->wake_on_lan);
>
> if (!gp->wake_on_lan) {
> /* According to Apple, we must set the MDIO pins to this begnign
> diff -ur a/drivers/net/sungem_phy.c b/drivers/net/sungem_phy.c
> --- a/drivers/net/sungem_phy.c 2004-10-18 23:53:45.000000000 +0200
> +++ b/drivers/net/sungem_phy.c 2004-11-10 08:59:20.000000000 +0100
> @@ -101,15 +101,17 @@
> return 0;
> }
>
> -static int bcm5201_suspend(struct mii_phy* phy, int wol_options)
> +void bcm_link_partner_hack(struct mii_phy *phy)
> {
> - if (!wol_options)
> - phy_write(phy, MII_BCM5201_INTERRUPT, 0);
> -
> /* Here's a strange hack used by both MacOS 9 and X */
> phy_write(phy, MII_LPA, phy_read(phy, MII_LPA));
> -
> +}
> +
> +static int bcm5201_suspend(struct mii_phy* phy, int wol_options)
> +{
> if (!wol_options) {
> + phy_write(phy, MII_BCM5201_INTERRUPT, 0);
> +
> #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
> u16 val = phy_read(phy, MII_BCM5201_AUXMODE2)
> phy_write(phy, MII_BCM5201_AUXMODE2,
> @@ -144,6 +146,20 @@
> return 0;
> }

The BCM52xx docs are available on Broadcom site.

> +static int bcm5221_suspend(struct mii_phy* phy, int wol_options)
> +{
> + if (!wol_options) {
> + u16 data = phy_read(phy, MII_BCM5221_TEST);
> + phy_write(phy, MII_BCM5221_TEST,
> + data | MII_BCM5221_TEST_ENABLE_SHADOWS);
> +
> + data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
> + phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
> + data | MII_BCM5221_IDDQ);
> + }
> + return 0;
> +}
> +
> static int bcm5400_init(struct mii_phy* phy)
> {
> u16 data;
> @@ -662,7 +678,7 @@
>
> /* Broadcom BCM 5221 */
> static struct mii_phy_ops bcm5221_phy_ops = {
> - .suspend = bcm5201_suspend,
> + .suspend = bcm5221_suspend,
> .init = bcm5221_init,
> .setup_aneg = genmii_setup_aneg,
> .setup_forced = genmii_setup_forced,
> diff -ur a/drivers/net/sungem_phy.h b/drivers/net/sungem_phy.h
> --- a/drivers/net/sungem_phy.h 2004-10-18 23:54:40.000000000 +0200
> +++ b/drivers/net/sungem_phy.h 2004-11-10 08:59:53.000000000 +0100
> @@ -53,6 +53,7 @@
> */
> extern int mii_phy_probe(struct mii_phy *phy, int mii_id);
>
> +void bcm_link_partner_hack(struct mii_phy *phy);
>
> /* MII definitions missing from mii.h */
>
> @@ -81,6 +82,7 @@
> #define MII_BCM5221_SHDOW_AUX_STAT2_APD 0x0020
> #define MII_BCM5221_SHDOW_AUX_MODE4 0x1a
> #define MII_BCM5221_SHDOW_AUX_MODE4_CLKLOPWR 0x0004
> +#define MII_BCM5221_IDDQ 0x0001
>
> /* MII BCM5400 1000-BASET Control register */
> #define MII_BCM5400_GB_CONTROL 0x09
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
Benjamin Herrenschmidt <benh@kernel.crashing.org>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 14:07    [W:0.184 / U:19.176 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site