Messages in this thread | | | Date | Tue, 02 Nov 2004 11:07:21 +1100 | From | Damien Moore <> | Subject | SATA drive freezing in 2.6.8.1 |
| |
Hi all,
(I'm not subscribed, because this is a work address. Please cc - much thanks)
I'm having some difficulties with a Seagate sata drive (ST3200822AS) when running a 2.6.8.1 kernel. After a seemingly random amount of time it fails with:
ata1: command 0x25 timeout, stat 0x50 host_stat 0x21 attempt to access beyond end of device sda1: rw=0, want=28160918024, limit=390716802 attempt to access beyond end of device sda1: rw=0, want=29781576712, limit=390716802 attempt to access beyond end of device sda1: rw=0, want=29964810632, limit=390716802 attempt to access beyond end of device sda1: rw=0, want=25778715784, limit=390716802 ATA: abnormal status 0x80 on port 0xEFE7 ATA: abnormal status 0x80 on port 0xEFE7 ATA: abnormal status 0x80 on port 0xEFE7
It took a while to pin down that it was actually the drive, because the only partition on it was NFS mounted to an older machine for a while.I'm concerned that there may be a hardware fault, because the first time it happened I restored everything and tried to give it some heavy work and everything was fine - but 3 weeks later it died with the same error twice in a row.
I'm going to try and go to 2.6.10, but if anyone has any help, it would be very appreciated - the machine seems to only fail when I'm trying to use it remotely, so its fairly frustrating.
thanks in advance, Damien
dmesg at bootup:
I/O APIC #2 Version 32 at 0xFEC00000. Enabling APIC mode: Flat. Using 1 I/O APICs Processors: 1 Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=302 Initializing CPU#0 CPU 0 irqstacks, hard=c0483000 soft=c0482000 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2998.841 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 513964k/523456k available (2255k kernel code, 8724k reserved, 1170k data , 140k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 5931.00 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2998.0069 MHz. ..... host bus clock speed is 199.0871 MHz. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: IRQ9 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5 ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10 ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 10 (level, low) -> IRQ 10 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1099353325.581:0): initialized Installing knfsd (copyright (C) 1996 okir@monad.swb.de). udf: registering filesystem ACPI: Power Button (FF) [PWRF] ACPI: Processor [CPU1] (supports C1) lp: driver loaded but no devices found Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 865 Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 64M @ 0xf8000000 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 (0x778) [PCSPP(,...)] parport0: irq 7 detected lp0: using parport0 (polling). Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 10 (level, low) -> IRQ 10 eth0: VIA VT86C100A Rhine at 0xd880, 00:50:ba:05:e6:37, IRQ 10. eth0: MII PHY found at address 8, status 0x782d advertising 05e1 Link 45e1. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio hda: QUANTUM FIREBALLlct15 30, ATA DISK drive hdb: QUANTUM FIREBALLP AS40.0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: SAMSUNG CD-ROM SC-152C, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 58680720 sectors (30044 MB) w/418KiB Cache, CHS=58215/16/63, UDMA(66) hda: hda1 hda2 hda3 hda4 hdb: max request size: 128KiB hdb: 78177792 sectors (40027 MB) w/1902KiB Cache, CHS=65535/16/63, UDMA(100) hdb: hdb1 hdc: ATAPI 52X CD-ROM drive, 128kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 libata version 1.02 loaded. ata_piix version 1.02 ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF60 irq 5 ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF68 irq 5 ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f ata1: dev 0 ATA, max UDMA/133, 390721968 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi0 : ata_piix ata2: SATA port has no device. scsi1 : ata_piix Vendor: ATA Model: ST3200822AS Rev: 3.01 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) SCSI device sda: drive cache: write back sda: sda1 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 uhci_hcd 0000:00:1d.0: port 2 portsc 0093 hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 es1371: version v0.32 time 22:07:56 Oct 11 2004 ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 5 (level, low) -> IRQ 5 es1371: found chip, vendor id 0x1274 device id 0x5880 revision 0x02 es1371: found es1371 rev 2 at io 0xdf00 irq 5 joystick 0x0 ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23) oprofile: using NMI interrupt. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) ip_conntrack version 2.1 (4089 buckets, 32712 max) - 300 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/proje cts/ipt_recent/ arp_tables: (C) 2002 David S. Miller NET: Registered protocol family 1 NET: Registered protocol family 17 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 140k freed
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |