lkml.org 
[lkml]   [2004]   [Oct]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: 2.6.9-mm1: NForce3 problem (IRQ sharing issue?)
Date
On Sunday 24 of October 2004 18:27, Zwane Mwaikambo wrote:
> On Sat, 23 Oct 2004, Rafael J. Wysocki wrote:
>
> > > Could we also get a dmesg and lspci? Boot with the 'debug' kernel
> > > parameter.
> >
> > Attached, for both 2.6.9-mm1 and 2.6.10-rc1.
>
> Could you boot 2.6.10-rc1 with the 'noapic' kernel parameter and you may
> as well remove that pci=routeirq parameter, then send dmesg. Something
> appears hosed with respect to IOAPIC setup and i think ACPI is having
> trouble doing the fallback to PIC mode.

I booted with noapic and without pci=routeirq, although I think it's still
necessary for suspend. The output of dmesg is attached (well, it's all I can
currently produce - I don't know how to get anything better).

Greets,
RJW

--
- Would you tell me, please, which way I ought to go from here?
- That depends a good deal on where you want to get to.
-- Lewis Carroll "Alice's Adventures in Wonderland"
Bootdata ok (command line is root=/dev/hdc6 vga=792 resume=/dev/hdc3 noapic nmi_watchdog=0 console=ttyS0,57600 console=tty0 debug)
Linux version 2.6.10-rc1 (rafael@albercik) (gcc version 3.3.3 (SuSE Linux)) #3 Sat Oct 23 20:14:56 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
No mptable found.
On node 0 totalpages: 130880
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126784 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000f76e0
ACPI: RSDT (v001 A M I OEMRSDT 0x04000413 MSFT 0x00000097) @ 0x000000001ff40000
ACPI: FADT (v001 A M I OEMFACP 0x04000413 MSFT 0x00000097) @ 0x000000001ff40200
ACPI: OEMB (v001 A M I OEMBIOS 0x04000413 MSFT 0x00000097) @ 0x000000001ff50040
>>> ERROR: Invalid checksum
ACPI: DSDT (v001 L5DK8 L5DK8013 0x00000013 INTL 0x02002026) @ 0x0000000000000000
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: ASUSTeK <6>Product ID: L5D <6>APIC at: 0xFEE00000
Processor #0 15:4 APIC version 16
I/O APIC #1 Version 17 at 0xFEC00000.
Processors: 1
Checking aperture...
CPU 0: aperture @ e8000000 size 128 MB
Built 1 zonelists
Kernel command line: root=/dev/hdc6 vga=792 resume=/dev/hdc3 noapic nmi_watchdog=0 console=ttyS0,57600 console=tty0 debug
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 65536 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1795.403 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 509548k/523520k available (2707k kernel code, 13424k reserved, 1111k data, 160k init)
Calibrating delay loop... 3555.32 BogoMIPS (lpj=1777664)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 0a
ACPI: IRQ9 SCI: Edge set to Level Trigger.
Using local APIC timer interrupts.
Detected 12.468 MHz APIC timer.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 37)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUS0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15)
ACPI: Power Resource [GFAN] (off)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LKSM] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LKMO] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:02:01.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:01.2[C] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI interrupt 0000:02:01.3[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:02:01.4[D] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xe8000000
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1098651312.659:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
vesafb: framebuffer at 0xd0000000, mapped to 0xffffff0000100000, using 6144k, total 65536k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 10 (level, low) -> IRQ 10
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hdb: TOSHIBA DVD-ROM SD-R2512, ATAPI CD/DVD-ROM drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: IC25N060ATMR04-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hdc: max request size: 1024KiB
hdc: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2 hdc3 hdc4 < hdc5 hdc6 hdc7 hdc8 hdc9 hdc10 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
Synaptics Touchpad, model: 1
Firmware: 5.9
180 degree mounted touchpad
Sensor: 18
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 28Kbytes
TCP: Hash tables configured (established 32768 bind 4681)
NET: Registered protocol family 1
PM: Reading pmdisk image.
swsusp: Resume From Partition: /dev/hdc3
<3>swsusp: Invalid partition type.
pmdisk: Error -22 resuming
PM: Resume from disk failed.
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
MDM P0P1 LAN0 LAN1 USB0 USB1 USB2 SLPB
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
(fs/jbd/recovery.c, 255): journal_recover: JBD: recovery, exit status 0, recovered transactions 280863 to 280877
(fs/jbd/recovery.c, 257): journal_recover: JBD: Replayed 503 and revoked 0/0 blocks
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 160k freed
Adding 1534196k swap on /dev/hdc3. Priority:42 extents:1
EXT3 FS on hdc6, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdc8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: hdc9: found reiserfs format "3.6" with standard journal
ReiserFS: hdc9: using ordered data mode
ReiserFS: hdc9: journal params: device hdc9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc9: checking transaction log (hdc9)
ReiserFS: hdc9: Using r5 hash to sort names
ReiserFS: hdc10: found reiserfs format "3.6" with standard journal
ReiserFS: hdc10: using ordered data mode
ReiserFS: hdc10: journal params: device hdc10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc10: checking transaction log (hdc10)
ReiserFS: hdc10: Using r5 hash to sort names
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80481ae0(lo)
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device 000001001f87cbe0(sit0)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
NET: Registered protocol family 17
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:02.0: nVidia Corporation nForce3 USB 1.1
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 11, pci mem 0xfebfb000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:02.1: nVidia Corporation nForce3 USB 1.1 (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 5, pci mem 0xfebfc000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 1-2: new low speed USB device using address 2
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
scatter-gather: enabled
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:02.2: nVidia Corporation nForce3 USB 2.0
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 10, pci mem 0xfebfdc00
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 1-2: USB disconnect, address 2
usb 1-2: new low speed USB device using address 3
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:02:01.0 [1043:1854]
Yenta: ISA IRQ mask 0x0098, PCI irq 9
Socket status: 30000006
ACPI: PCI interrupt 0000:02:01.1[B] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:01.1 [1043:1854]
Yenta: ISA IRQ mask 0x0098, PCI irq 11
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:01.2[C] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[feafd000-feafd7ff] Max Packet=[2048]
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:02.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ACPI: AC Adapter [AC0] (on-line)
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:06.0 to 64
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000319b175]
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ACPI: Fan [FN00] (off)
ACPI: Processor [CPU1] (supports C1)
ACPI: Thermal Zone [THRM] (57 C)
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x2 (1500 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6 (1400 mV)
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0xa, vid 0x2
intel8x0_measure_ac97_clock: measured 49503 usecs
intel8x0: clocking to 47365
ALSA sound/pci/intel8x0.c:2841: joystick(s) found
eth0: no IPv6 routers present
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
SCSI subsystem initialized
st: Version 20040403, fixed bufsize 32768, s/g segs 256
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
usb usb2: string descriptor 0 read error: -113
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
\
 
 \ /
  Last update: 2005-03-22 14:07    [W:0.056 / U:8.992 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site