lkml.org 
[lkml]   [2003]   [Sep]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Subject2.6.0-test5 (nearly) success story
    From
    Date
    Hi,

    Just compiled and booted 2.6.0-test5 on my Fujitsu-Siemens notebook
    (Liteline LF6, Celeron 600 MHz class, i440BX etc). No modules.

    gcc version 3.2.3 20030422 (older rawhide - Red Hat Linux 3.2.3-4)

    Problems:
    1. with cardbus ethernet (DEC tulip 21143-based D-Link DFE-660TX) inserted,
    boot process stops after printing something like:

    Yenta: CardBus bridge found at 0000:00:0a.0 [110a:0015]
    Yenta: Enabling burst memory read transactions
    Yenta: Using CSCINT to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta: ISA IRQ list 0090, PCI irq9
    Socket status: 30000020

    No caps/scroll/num lock LEDs working, it's dead.

    With the ethernet card removed before starting kernel, it completes:

    Yenta: CardBus bridge found at 0000:00:0a.0 [110a:0015]
    Yenta: Enabling burst memory read transactions
    Yenta: Using CSCINT to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta: ISA IRQ list 0090, PCI irq9
    Socket status: 30000006
    Yenta: CardBus bridge found at 0000:00:0a.1 [110a:0015]
    Yenta: Using CSCINT to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta: ISA IRQ list 0090, PCI irq11
    Socket status: 30000006
    mice: PS/2 mouse device common for all mice
    ...

    The ethernet works if I insert it then.



    2. The kernel prints:

    Local APIC disabled by BIOS -- reenabling.
    Could not enable APIC!

    Not sure if it's ok - happens with 2.4, too.


    3. ACPI - while booting the kernel says:
    ACPI: AC Adapter [ACAD] (off-line)
    ACPI: Battery Slot [BAT1] (battery absent)

    with both external power and battery connected. It is correct after
    boot, though. The same with 2.4.

    And:
    cpufreq: No CPUs supporting ACPI performance management found.
    ACPI: (supports S0 S3 S4 S5)

    while:
    # cat /proc/acpi/processor/CPU0/throttling
    state count: 8
    active state: T0
    states:
    *T0: 00%
    T1: 12%
    T2: 25%
    T3: 37%
    T4: 50%
    T5: 62%
    T6: 75%
    T7: 87%

    Not sure if it's related.


    .config etc follows.


    CONFIG_X86=y
    CONFIG_MMU=y
    CONFIG_UID16=y
    CONFIG_GENERIC_ISA_DMA=y
    CONFIG_EXPERIMENTAL=y
    CONFIG_CLEAN_COMPILE=y
    CONFIG_STANDALONE=y
    CONFIG_BROKEN_ON_SMP=y
    CONFIG_SWAP=y
    CONFIG_SYSVIPC=y
    CONFIG_SYSCTL=y
    CONFIG_LOG_BUF_SHIFT=14
    CONFIG_KALLSYMS=y
    CONFIG_FUTEX=y
    CONFIG_EPOLL=y
    CONFIG_IOSCHED_NOOP=y
    CONFIG_IOSCHED_AS=y
    CONFIG_IOSCHED_DEADLINE=y
    CONFIG_X86_PC=y
    CONFIG_MPENTIUMIII=y
    CONFIG_X86_CMPXCHG=y
    CONFIG_X86_XADD=y
    CONFIG_X86_L1_CACHE_SHIFT=5
    CONFIG_RWSEM_XCHGADD_ALGORITHM=y
    CONFIG_X86_WP_WORKS_OK=y
    CONFIG_X86_INVLPG=y
    CONFIG_X86_BSWAP=y
    CONFIG_X86_POPAD_OK=y
    CONFIG_X86_GOOD_APIC=y
    CONFIG_X86_INTEL_USERCOPY=y
    CONFIG_X86_USE_PPRO_CHECKSUM=y
    CONFIG_PREEMPT=y
    CONFIG_X86_TSC=y
    CONFIG_X86_MCE=y
    CONFIG_NOHIGHMEM=y
    CONFIG_MTRR=y
    CONFIG_HAVE_DEC_LOCK=y
    CONFIG_PM=y
    CONFIG_SOFTWARE_SUSPEND=y
    CONFIG_ACPI_HT=y
    CONFIG_ACPI=y
    CONFIG_ACPI_BOOT=y
    CONFIG_ACPI_SLEEP=y
    CONFIG_ACPI_SLEEP_PROC_FS=y
    CONFIG_ACPI_AC=y
    CONFIG_ACPI_BATTERY=y
    CONFIG_ACPI_BUTTON=y
    CONFIG_ACPI_FAN=y
    CONFIG_ACPI_PROCESSOR=y
    CONFIG_ACPI_THERMAL=y
    CONFIG_ACPI_BUS=y
    CONFIG_ACPI_INTERPRETER=y
    CONFIG_ACPI_EC=y
    CONFIG_ACPI_POWER=y
    CONFIG_ACPI_PCI=y
    CONFIG_ACPI_SYSTEM=y
    CONFIG_CPU_FREQ=y
    CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
    CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
    CONFIG_CPU_FREQ_GOV_POWERSAVE=y
    CONFIG_CPU_FREQ_GOV_USERSPACE=y
    CONFIG_CPU_FREQ_TABLE=y
    CONFIG_X86_ACPI_CPUFREQ=y
    CONFIG_X86_SPEEDSTEP_ICH=y
    CONFIG_X86_SPEEDSTEP_CENTRINO=y
    CONFIG_X86_SPEEDSTEP_LIB=y
    CONFIG_PCI=y
    CONFIG_PCI_GODIRECT=y
    CONFIG_PCI_DIRECT=y
    CONFIG_PCI_NAMES=y
    CONFIG_ISA=y
    CONFIG_HOTPLUG=y
    CONFIG_PCMCIA=y
    CONFIG_YENTA=y
    CONFIG_CARDBUS=y
    CONFIG_PCMCIA_PROBE=y
    CONFIG_BINFMT_ELF=y
    CONFIG_BINFMT_MISC=y
    CONFIG_PARPORT=y
    CONFIG_PARPORT_PC=y
    CONFIG_PARPORT_PC_FIFO=y
    CONFIG_PARPORT_PC_SUPERIO=y
    CONFIG_PARPORT_1284=y
    CONFIG_PNP=y
    CONFIG_PNPBIOS=y
    CONFIG_BLK_DEV_FD=y
    CONFIG_BLK_DEV_LOOP=y
    CONFIG_IDE=y
    CONFIG_BLK_DEV_IDE=y
    CONFIG_BLK_DEV_IDEDISK=y
    CONFIG_IDEDISK_MULTI_MODE=y
    CONFIG_BLK_DEV_IDECD=y
    CONFIG_BLK_DEV_IDEPCI=y
    CONFIG_IDEPCI_SHARE_IRQ=y
    CONFIG_BLK_DEV_GENERIC=y
    CONFIG_BLK_DEV_IDEDMA_PCI=y
    CONFIG_IDEDMA_PCI_AUTO=y
    CONFIG_BLK_DEV_ADMA=y
    CONFIG_BLK_DEV_PIIX=y
    CONFIG_BLK_DEV_IDEDMA=y
    CONFIG_IDEDMA_AUTO=y
    CONFIG_NET=y
    CONFIG_PACKET=y
    CONFIG_PACKET_MMAP=y
    CONFIG_UNIX=y
    CONFIG_INET=y
    CONFIG_INET_ECN=y
    CONFIG_NETFILTER=y
    CONFIG_IP_NF_CONNTRACK=y
    CONFIG_IP_NF_FTP=y
    CONFIG_IP_NF_IPTABLES=y
    CONFIG_IP_NF_NAT=y
    CONFIG_IP_NF_NAT_NEEDED=y
    CONFIG_IP_NF_TARGET_MASQUERADE=y
    CONFIG_IP_NF_NAT_FTP=y
    CONFIG_IPV6_SCTP__=y
    CONFIG_NETDEVICES=y
    CONFIG_NET_ETHERNET=y
    CONFIG_NET_TULIP=y
    CONFIG_TULIP=y
    CONFIG_NET_PCI=y
    CONFIG_PLIP=y
    CONFIG_PPP=y
    CONFIG_PPP_ASYNC=y
    CONFIG_PPP_DEFLATE=y
    CONFIG_PPP_BSDCOMP=y
    CONFIG_IRDA=y
    CONFIG_IRLAN=y
    CONFIG_IRNET=y
    CONFIG_IRCOMM=y
    CONFIG_IRDA_ULTRA=y
    CONFIG_IRDA_CACHE_LAST_LSAP=y
    CONFIG_IRDA_FAST_RR=y
    CONFIG_NSC_FIR=y
    CONFIG_INPUT=y
    CONFIG_INPUT_MOUSEDEV=y
    CONFIG_INPUT_MOUSEDEV_PSAUX=y
    CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
    CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
    CONFIG_SOUND_GAMEPORT=y
    CONFIG_SERIO=y
    CONFIG_SERIO_I8042=y
    CONFIG_SERIO_SERPORT=y
    CONFIG_INPUT_KEYBOARD=y
    CONFIG_KEYBOARD_ATKBD=y
    CONFIG_INPUT_MOUSE=y
    CONFIG_MOUSE_PS2=y
    CONFIG_INPUT_MISC=y
    CONFIG_INPUT_PCSPKR=y
    CONFIG_VT=y
    CONFIG_VT_CONSOLE=y
    CONFIG_HW_CONSOLE=y
    CONFIG_UNIX98_PTYS=y
    CONFIG_UNIX98_PTY_COUNT=64
    CONFIG_I2C=y
    CONFIG_I2C_PIIX4=y
    CONFIG_SENSORS_IT87=y
    CONFIG_SENSORS_LM75=y
    CONFIG_SENSORS_LM85=y
    CONFIG_SENSORS_LM78=y
    CONFIG_SENSORS_W83781D=y
    CONFIG_I2C_SENSOR=y
    CONFIG_RTC=y
    CONFIG_AGP=y
    CONFIG_AGP_INTEL=y
    CONFIG_EXT3_FS=y
    CONFIG_EXT3_FS_XATTR=y
    CONFIG_JBD=y
    CONFIG_FS_MBCACHE=y
    CONFIG_ISO9660_FS=y
    CONFIG_JOLIET=y
    CONFIG_UDF_FS=y
    CONFIG_FAT_FS=y
    CONFIG_VFAT_FS=y
    CONFIG_PROC_FS=y
    CONFIG_DEVPTS_FS=y
    CONFIG_TMPFS=y
    CONFIG_RAMFS=y
    CONFIG_SMB_FS=y
    CONFIG_SMB_NLS_DEFAULT=y
    CONFIG_SMB_NLS_REMOTE="cp852"
    CONFIG_MSDOS_PARTITION=y
    CONFIG_SMB_NLS=y
    CONFIG_NLS=y
    CONFIG_NLS_DEFAULT="iso8859-2"
    CONFIG_NLS_CODEPAGE_437=y
    CONFIG_NLS_CODEPAGE_850=y
    CONFIG_NLS_CODEPAGE_852=y
    CONFIG_NLS_ISO8859_1=y
    CONFIG_NLS_ISO8859_2=y
    CONFIG_NLS_UTF8=y
    CONFIG_VIDEO_SELECT=y
    CONFIG_VGA_CONSOLE=y
    CONFIG_DUMMY_CONSOLE=y
    CONFIG_SOUND=y
    CONFIG_SND=y
    CONFIG_SND_SEQUENCER=y
    CONFIG_SND_OSSEMUL=y
    CONFIG_SND_MIXER_OSS=y
    CONFIG_SND_PCM_OSS=y
    CONFIG_SND_SEQUENCER_OSS=y
    CONFIG_SND_RTCTIMER=y
    CONFIG_SND_MAESTRO3=y
    CONFIG_DEBUG_KERNEL=y
    CONFIG_DEBUG_STACKOVERFLOW=y
    CONFIG_DEBUG_SLAB=y
    CONFIG_DEBUG_IOVIRT=y
    CONFIG_MAGIC_SYSRQ=y
    CONFIG_DEBUG_SPINLOCK_SLEEP=y
    CONFIG_ZLIB_INFLATE=y
    CONFIG_ZLIB_DEFLATE=y
    CONFIG_X86_BIOS_REBOOT=y

    00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 64
    Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
    Capabilities: [a0] AGP version 1.0
    Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
    Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

    00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 128
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
    Memory behind bridge: f8000000-fbffffff
    BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+

    00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0

    00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64
    Region 4: I/O ports at fcd0 [size=16]

    00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64
    Interrupt: pin D routed to IRQ 11
    Region 4: I/O ports at fce0 [size=32]

    00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin ? routed to IRQ 9

    00:0a.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
    Subsystem: Siemens Nixdorf AG: Unknown device 0015
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168, cache line size 08
    Interrupt: pin A routed to IRQ 9
    Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
    Memory window 0: 10400000-107ff000 (prefetchable)
    Memory window 1: 10800000-10bff000
    I/O window 0: 00001000-000010ff
    I/O window 1: 00001400-000014ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
    16-bit legacy interface ports at 0001

    00:0a.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
    Subsystem: Siemens Nixdorf AG: Unknown device 0015
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168, cache line size 08
    Interrupt: pin B routed to IRQ 11
    Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
    Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
    Memory window 0: 10c00000-10fff000 (prefetchable)
    Memory window 1: 11000000-113ff000
    I/O window 0: 00001800-000018ff
    I/O window 1: 00001c00-00001cff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001

    00:0d.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i PCI Audio Accelerator
    Subsystem: Siemens Nixdorf AG: Unknown device 1998
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (500ns min, 6000ns max)
    Interrupt: pin A routed to IRQ 5
    Region 0: I/O ports at f800 [size=256]
    Region 1: Memory at fedfe000 (32-bit, non-prefetchable) [size=8K]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    00:0d.1 Communication controller: ESS Technology ES1983S Maestro-3i PCI Modem Accelerator
    Subsystem: Siemens Nixdorf AG: Unknown device 1998
    Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 5
    Region 0: I/O ports at f400 [size=256]
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=100mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    01:00.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev b1) (prog-if 00 [VGA])
    Subsystem: Siemens Nixdorf AG: Unknown device 0720
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64
    Interrupt: pin A routed to IRQ 9
    Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
    Capabilities: [40] Power Management version 1
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [50] AGP version 2.0
    Status: RQ=15 SBA+ 64bit- FW- Rate=x2
    Command: RQ=15 SBA+ AGP+ 64bit- FW- Rate=x2

    02:00.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)
    Subsystem: D-Link System Inc: Unknown device 1142
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (5000ns min, 10000ns max)
    Interrupt: pin A routed to IRQ 9
    Region 0: I/O ports at 1000 [size=128]
    Region 1: Memory at 10800000 (32-bit, non-prefetchable) [size=1K]
    Expansion ROM at 10400000 [disabled] [size=256K]



    Linux version 2.6.0-test5 (khc@defiant) (gcc version 3.2.3 20030422 (Red Hat Linux 3.2.3-4)) #2 Fri Sep 12 14:11:18 CEST 2003
    Video mode to be used for restore is f00
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000eac00 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
    BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
    BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
    BIOS-e820: 00000000fffeac00 - 0000000100000000 (reserved)
    127MB LOWMEM available.
    On node 0 totalpages: 32752
    DMA zone: 4096 pages, LIFO batch:1
    Normal zone: 28656 pages, LIFO batch:6
    HighMem zone: 0 pages, LIFO batch:1
    DMI 2.2 present.
    ACPI: RSDP (v000 PTLTD ) @ 0x000f7400
    ACPI: RSDT (v001 PTLTD C3 RSDT 0xf0cf0033 LTP 0x00000000) @ 0x07ffaabe
    ACPI: FADT (v001 QUANTA C3 FACP 0xf0cf0033 PTL 0x000f4240) @ 0x07fffb8c
    ACPI: DSDT (v001 PTL C3 DSDT 0xf0cf0033 MSFT 0x0100000c) @ 0x00000000
    Building zonelist for node : 0
    Kernel command line: auto BOOT_IMAGE=L2.6.0test5 root=302 BOOT_FILE=/lib/modules/2.6.0-test5/bzImage
    Initializing CPU#0
    PID hash table entries: 512 (order 9: 4096 bytes)
    Detected 597.652 MHz processor.
    Console: colour VGA+ 80x25
    Memory: 125604k/131008k available (2413k kernel code, 4868k reserved, 809k data, 136k init, 0k highmem)
    Calibrating delay loop... 1179.64 BogoMIPS
    Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    -> /dev
    -> /dev/console
    -> /root
    CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
    CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
    CPU: L1 I cache: 16K, L1 D cache: 16K
    CPU: L2 cache: 128K
    CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
    Intel machine check architecture supported.
    Intel machine check reporting enabled on CPU#0.
    CPU: Intel Celeron (Coppermine) stepping 06
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Checking 'hlt' instruction... OK.
    POSIX conformance testing by UNIFIX
    NET: Registered protocol family 16
    PCI: Using configuration type 1
    mtrr: v2.0 (20020519)
    ACPI: Subsystem revision 20030813
    ACPI: Interpreter enabled
    ACPI: Using PIC for interrupt routing
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
    ACPI: PCI Root Bridge [PCI0] (00:00)
    PCI: Probing PCI hardware (bus 00)
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: Embedded Controller [EC0] (gpe 0)
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
    ACPI: Power Resource [PFAN] (off)
    Linux Plug and Play Support v0.97 (c) Adam Belay
    PnPBIOS: Scanning system for PnP BIOS support...
    PnPBIOS: Found PnP BIOS installation structure at 0xc00f7450
    PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xa81b, dseg 0x400
    PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
    Linux Kernel Card Services 3.1.22
    options: [pci] [cardbus] [pm]
    ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
    ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
    ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
    ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
    PCI: Using ACPI for IRQ routing
    PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
    NET: Registered protocol family 23
    pty: 256 Unix98 ptys configured
    udf: registering filesystem
    Limiting direct PCI/PCI transfers.
    ACPI: AC Adapter [ACAD] (off-line)
    ACPI: Battery Slot [BAT1] (battery absent)
    ACPI: Power Button (FF) [PWRF]
    ACPI: Lid Switch [LID]
    ACPI: Sleep Button (CM) [SBTN]
    ACPI: Fan [FAN] (off)
    ACPI: Processor [CPU0] (supports C1 C2, 8 throttling states)
    ACPI: Thermal Zone [THRM] (64 C)
    Real Time Clock Driver v1.12
    Linux agpgart interface v0.100 (c) Dave Jones
    agpgart: Detected an Intel 440BX Chipset.
    agpgart: Maximum main memory to use for agp memory: 94M
    agpgart: AGP aperture is 64M @ 0xf4000000
    parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
    parport0: irq 7 detected
    parport0: cpp_daisy: aa5500ff(38)
    parport0: assign_addrs: aa5500ff(38)
    parport0: cpp_daisy: aa5500ff(38)
    parport0: assign_addrs: aa5500ff(38)
    Using anticipatory scheduling io scheduler
    Floppy drive(s): fd0 is 1.44M
    FDC 0 is a National Semiconductor PC87306
    loop: loaded (max 8 devices)
    plip: parport0 has no IRQ. Using IRQ-less mode,which is fairly inefficient!
    NET3 PLIP version 2.4-parport gniibe@mri.co.jp
    plip0: Parallel port at 0x378, not using IRQ.
    PPP generic driver version 2.4.2
    PPP Deflate Compression module registered
    PPP BSD Compression module registered
    nsc-ircc, Found chip at base=0x398
    nsc-ircc, driver loaded (Dag Brattli)
    IrDA: Registered device irda0
    nsc-ircc, Found dongle: Sharp RY5HD01
    Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
    ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
    PIIX4: IDE controller at PCI slot 0000:00:07.1
    PIIX4: chipset revision 1
    PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:pio, hdd:pio
    hda: IBM-DJSA-205, ATA DISK drive
    ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
    hdc: CD-224E, ATAPI CD/DVD-ROM drive
    ide1 at 0x170-0x177,0x376 on irq 15
    hda: max request size: 128KiB
    hda: 9767520 sectors (5000 MB) w/384KiB Cache, CHS=10336/15/63, UDMA(33)
    hda: hda1 hda2 hda3
    hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
    Uniform CD-ROM driver Revision: 3.12
    Yenta: CardBus bridge found at 0000:00:0a.0 [110a:0015]
    Yenta: Enabling burst memory read transactions
    Yenta: Using CSCINT to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta: ISA IRQ list 0090, PCI irq9
    Socket status: 30000006
    Yenta: CardBus bridge found at 0000:00:0a.1 [110a:0015]
    Yenta: Using CSCINT to route CSC interrupts to PCI
    Yenta: Routing CardBus interrupts to PCI
    Yenta: ISA IRQ list 0090, PCI irq11
    Socket status: 30000006
    mice: PS/2 mouse device common for all mice
    input: PC Speaker
    Synaptics Touchpad, model: 1
    Firware: 4.6
    Sensor: 19
    new absolute packet format
    Touchpad has extended capability bits
    -> multifinger detection
    -> palm detection
    input: Synaptics Synaptics TouchPad on isa0060/serio1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    input: AT Set 2 keyboard on isa0060/serio0
    serio: i8042 KBD port at 0x60,0x64 irq 1
    i2c-piix4 version 2.7.0 (20021208)
    piix4-smbus 0000:00:07.3: Found 0000:00:07.3 device
    Advanced Linux Sound Architecture Driver Version 0.9.6 (Wed Aug 20 20:27:13 2003 UTC).
    ALSA device list:
    #0: ESS Maestro3 PCI at 0xf800, irq 5
    NET: Registered protocol family 2
    IP: routing cache hash table of 512 buckets, 4Kbytes
    TCP: Hash tables configured (established 8192 bind 16384)
    ip_conntrack version 2.1 (1023 buckets, 8184 max) - 300 bytes per conntrack
    ip_tables: (C) 2000-2002 Netfilter core team
    NET: Registered protocol family 1
    NET: Registered protocol family 17
    IrCOMM protocol (Dag Brattli)
    cpufreq: No CPUs supporting ACPI performance management found.
    ACPI: (supports S0 S3 S4 S5)
    kjournald starting. Commit interval 5 seconds
    EXT3-fs: mounted filesystem with ordered data mode.
    VFS: Mounted root (ext3 filesystem) readonly.
    Freeing unused kernel memory: 136k freed
    Linux Tulip driver version 1.1.13 (May 11, 2002)
    PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    tulip0: EEPROM default media type Autosense.
    tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
    tulip0: MII transceiver #0 config 3000 status 7809 advertising 01e1.
    eth0: Digital DS21143 Tulip rev 65 at 0x1000, 00:50:BA:70:68:3E, IRQ 9.
    EXT3 FS on hda2, internal journal
    Adding 120476k swap on /dev/hda3. Priority:-1 extents:1
    eth0: Setting full-duplex based on MII#0 link partner capability of 45e1.
    blk: queue c7ec2064, I/O limit 4095Mb (mask 0xffffffff)

    --
    Krzysztof Halasa, B*FH
    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:48    [W:0.051 / U:0.476 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site