lkml.org 
[lkml]   [2003]   [Sep]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectRe: Omnibook PCMCIA slots unusable after suspend.
    Date
    On 2003-09-10 at 23:45BST Russell King wrote:
    > On Wed, Sep 10, 2003 at 10:22:32PM +0100, Jon Fairbairn wrote:
    > > In short: I'm using an HP Ombibook 800CT, have started using
    > > a Carbus PCMCIA network card and am losing the card after
    > > suspends.
    >
    > I'm only interested in the 2.6.0-test5 results.

    OK. Pause for recompilation...

    > Please run lspci -vvb twice - once when you have just booted
    > the machine, and once when you resume.

    The following is done without unloading the modules round
    the suspend.

    Before:
    ------
    00:00.0 Host bridge: VLSI Technology Inc 82C535 (rev 03)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0

    00:01.0 PCI bridge: VLSI Technology Inc 82C534 [Eagle] (rev 03) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 00004000-00007fff
    Memory behind bridge: 20000000-2fffffff
    Prefetchable memory behind bridge: 30000000-3fffffff
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset+ FastB2B-

    00:02.0 Class ff00: VLSI Technology Inc 82C532 (rev 02)
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

    00:03.0 VGA compatible controller: Neomagic Corporation NM2070 [MagicGraph 128] (rev 01) (prog-if 00 [VGA])
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 0
    Region 0: Memory at c0000000 (32-bit, prefetchable)

    00:04.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168, cache line size 08
    Interrupt: pin A routed to IRQ 9
    Region 0: Memory at 000e6000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
    Memory window 0: 10000000-103ff000 (prefetchable)
    Memory window 1: 10400000-107ff000
    I/O window 0: 00008000-000080ff
    I/O window 1: 00008400-000084ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
    16-bit legacy interface ports at 0001

    00:04.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168, cache line size 08
    Interrupt: pin B routed to IRQ 7
    Region 0: Memory at 000e7000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
    Memory window 0: 10800000-10bff000 (prefetchable)
    Memory window 1: 10c00000-10fff000
    I/O window 0: 00008800-000088ff
    I/O window 1: 00008c00-00008cff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001

    00:06.0 IRDA controller: VLSI Technology Inc 82C147 (rev 02)
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 0
    Region 0: I/O ports at 1000 [disabled]

    02:00.0 Ethernet controller: Linksys Fast Ethernet 10/100 (rev 11)
    Subsystem: Netgear FA511 10/100
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 64 (63750ns min, 63750ns max)
    Interrupt: pin A routed to IRQ 9
    Region 0: I/O ports at 8000
    Region 1: Memory at 10400000 (32-bit, non-prefetchable)
    Capabilities: [c0] Power Management version 2
    Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    Status: D0 PME-Enable- DSel=0 DScale=0 PME-

    ------
    After:
    ------

    00:00.0 Host bridge: VLSI Technology Inc 82C535 (rev 03)
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
    Latency: 0

    00:01.0 PCI bridge: VLSI Technology Inc 82C534 [Eagle] (rev 03) (prog-if 00 [Normal decode])
    Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 0
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 00004000-00007fff
    Memory behind bridge: 20000000-2fffffff
    Prefetchable memory behind bridge: 30000000-3fffffff
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset+ FastB2B-

    00:02.0 Class ff00: VLSI Technology Inc 82C532 (rev 02)
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

    00:03.0 VGA compatible controller: Neomagic Corporation NM2070 [MagicGraph 128] (rev 01) (prog-if 00 [VGA])
    Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 0
    Region 0: Memory at c0000000 (32-bit, prefetchable)

    00:04.0 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168, cache line size 08
    Interrupt: pin A routed to IRQ 9
    Region 0: Memory at 000e6000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
    Memory window 0: 10000000-103ff000 (prefetchable)
    Memory window 1: 10400000-107ff000
    I/O window 0: 00008000-000080ff
    I/O window 1: 00008400-000084ff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
    16-bit legacy interface ports at 0001

    00:04.1 CardBus bridge: Texas Instruments PCI1130 (rev 04)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Latency: 168, cache line size 08
    Interrupt: pin B routed to IRQ 7
    Region 0: Memory at 000e7000 (32-bit, non-prefetchable)
    Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
    Memory window 0: 10800000-10bff000 (prefetchable)
    Memory window 1: 10c00000-10fff000
    I/O window 0: 00008800-000088ff
    I/O window 1: 00008c00-00008cff
    BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
    16-bit legacy interface ports at 0001

    00:06.0 IRDA controller: VLSI Technology Inc 82C147 (rev 02)
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
    Interrupt: pin A routed to IRQ 0
    Region 0: I/O ports at 1000 [disabled]

    02:00.0 Class ffff: Linksys Fast Ethernet 10/100 (rev ff) (prog-if ff)
    !!! Unknown header type 7f

    ------

    So there's a Reset- v a Reset+ there.

    Curiously, the output after a suspend on mains is the same
    (says diff) as the output after a suspend on battery, even
    though the former doesn't stop it working while the latter
    does.


    > > ...
    > > Sep 6 23:23:55 graffito kernel: Socket status: 2a035c8a
    >
    > It looks like the cardbus controller configuration wasn't correctly
    > restored.

    Indeed, though it always seems to give the same dodgy looking
    status.

    > --
    > Russell King (rmk@arm.linux.org.uk) http://www.arm.linux.org.uk/personal/
    > Linux kernel maintainer of:
    > 2.6 ARM Linux - http://www.arm.linux.org.uk/

    Wish I still had an ARM...
    --
    Jón Fairbairn


    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:48    [W:0.032 / U:148.872 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site