lkml.org 
[lkml]   [2003]   [Aug]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectYenta init freezes Pavilion
From
Date
Hello,

Please bear with me, I'm not very familiar with submitting problem
reports.
When booting my HP Pavilion zt1145 (see below), the system freezes
once it gets to checking the cardbus status:

Yenta IRQ list 0000, PCI irq11
Socket status: 30000006

This is with pci=noacpi acpi=off. Without those options, it'll
typically freeze a little later in the boot process, well before init.
The laptop boots fine without Yenta support compiled in.

The following was collected when booting from 2.4.20.

Output from lspci:

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit-
FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: e0000000-efffffff
Prefetchable memory behind bridge: 90000000-9fffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001

00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e200 [size=256]
Region 1: Memory at f0000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0e.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63750ns min, 63750ns max), cache line size 04
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f0000800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at e300 [size=128]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 Communication controller: ESS Technology ES2838/2839 SuperLink
Modem (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e380 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME+

00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge]
(rev 10)
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus
Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1100 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1e) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at 1200 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1e) (prog-if 00
[UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at 1300 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686
AC97 Audio Controller (rev 40)
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at e000 [size=256]
Region 1: I/O ports at e100 [size=4]
Region 2: I/O ports at e104 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266]
(rev 02) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 0020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max), cache line size 04
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=512K]
Region 1: Memory at 90000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at 000c0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit-
FW- AGP3- Rate=x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4

Output from /proc/iomem:

00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-0efeffff : System RAM
00100000-00274268 : Kernel code
00274269-002ccbff : Kernel data
0eff0000-0effffbf : ACPI Tables
0effffc0-0effffff : ACPI Non-volatile Storage
10000000-10000fff : PCI device 1524:1410
10400000-107fffff : PCI CardBus #02
10800000-10bfffff : PCI CardBus #02
60000000-60000fff : card services
90000000-9fffffff : PCI Bus #01
90000000-97ffffff : PCI device 5333:8d01
a0000000-a3ffffff : PCI device 1106:0605
e0000000-efffffff : PCI Bus #01
e0000000-e007ffff : PCI device 5333:8d01
f0000000-f00000ff : PCI device 10ec:8139
f0000000-f00000ff : 8139too
f0000800-f0000fff : PCI device 1106:3044
fff80000-ffffffff : reserved

Output from /proc/ioports:

0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-013f : orinoco_cs
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1100-110f : PCI device 1106:0571
1100-1107 : ide0
1108-110f : ide1
1200-121f : PCI device 1106:3038
1200-121f : usb-uhci
1300-131f : PCI device 1106:3038
1300-131f : usb-uhci
4000-40ff : PCI CardBus #02
4400-44ff : PCI CardBus #02
c000-dfff : PCI Bus #01
e000-e0ff : PCI device 1106:3058
e000-e0ff : VIA686A
e100-e103 : PCI device 1106:3058
e104-e107 : PCI device 1106:3058
e200-e2ff : PCI device 10ec:8139
e200-e2ff : 8139too
e300-e37f : PCI device 1106:3044
e380-e38f : PCI device 125d:2838

Sorry if this is too much or too little information. Please let me know
of anything I can do to help. I'll be trying previous kernels to see if
I can narrow down where this problem began occurring.
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2005-03-22 13:47    [W:0.032 / U:0.660 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site