lkml.org 
[lkml]   [2003]   [Aug]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject[Fwd: Re: via rhine network failure on 2.6.0-test4]
   Do dmidecode and acpidump have to be run while booted to the failing 
kernel (2.6.0-test4)? If so I will need to rebuild test4 with ACPI on
again tonight to get it to fail. Otherwise here is the output from
dmidecode run on the same system while booted to 2.4. I will open a
bug on bugzilla later today if I can track down my bugzilla id.

# dmidecode 2.2
SMBIOS 2.2 present.
36 structures occupying 961 bytes.
Table at 0x000F0800.
Handle 0x0000
DMI type 0, 19 bytes.
BIOS Information
Vendor: Award Software International, Inc.
Version: 6.00 PG
Release Date: 11/13/2001
Address: 0xE0000
Runtime Size: 128 kB
ROM Size: 256 kB
Characteristics:
ISA is supported
PCI is supported
PNP is supported
APM is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
BIOS ROM is socketed
EDD is supported
5.25"/360 KB floppy services are supported (int 13h)
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 KB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
AGP is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
Handle 0x0001
DMI type 1, 25 bytes.
System Information
Manufacturer: VIA Technologies, Inc.
Product Name: VT8366-8233
Version:
Serial Number:
UUID: Not Present
Wake-up Type: Power Switch
Handle 0x0002
DMI type 2, 8 bytes.
Base Board Information
Manufacturer:
Product Name: VT8366-8233
Version:
Serial Number:
Handle 0x0003
DMI type 3, 13 bytes.
Chassis Information
Manufacturer:
Type: Desktop
Lock: Not Present
Version:
Serial Number:
Asset Tag:
Boot-up State: Unknown
Power Supply State: Unknown
Thermal State: Unknown
Security Status: Unknown
Handle 0x0004
DMI type 4, 32 bytes.
Processor Information
Socket Designation: Socket A
Type: Central Processor
Family: Duron
Manufacturer: AMD
ID: 62 06 00 00 FF F9 83 03
Signature: Type 0, Family 6, Model 6, Stepping 2
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
Version: AMD Athlon(tm) XP
Voltage: 3.3 V
External Clock: 133 MHz
Max Speed: 1500 MHz
Current Speed: 1600 MHz
Status: Populated, Enabled
Upgrade: ZIF Socket
L1 Cache Handle: 0x0009
L2 Cache Handle: 0x000A
L3 Cache Handle: No L3 Cache
Handle 0x0005
DMI type 5, 22 bytes.
Memory Controller Information
Error Detecting Method: None
Error Correcting Capabilities:
None
Supported Interleave: One-way Interleave
Current Interleave: Four-way Interleave
Maximum Memory Module Size: 32 MB
Maximum Total Memory Size: 96 MB
Supported Speeds:
70 ns
60 ns
Supported Memory Types:
Standard
EDO
Memory Module Voltage: 5.0 V
Associated Memory Slots: 3
0x0006
0x0007
0x0008
Enabled Error Correcting Capabilities: None
Handle 0x0006
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A0
Bank Connections: 0 1
Current Speed: 60 ns
Type: Unknown
Installed Size: 512 MB (Double-bank Connection)
Enabled Size: 512 MB (Double-bank Connection)
Error Status: OK
Handle 0x0007
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A1
Bank Connections: 2
Current Speed: 60 ns
Type: Unknown
Installed Size: 512 MB (Single-bank Connection)
Enabled Size: 512 MB (Single-bank Connection)
Error Status: OK
Handle 0x0008
DMI type 6, 12 bytes.
Memory Module Information
Socket Designation: A2
Bank Connections: None
Current Speed: 60 ns
Type: Unknown
Installed Size: Not Installed (Single-bank Connection)
Enabled Size: Not Installed (Single-bank Connection)
Error Status: OK
Handle 0x0009
DMI type 7, 19 bytes.
Cache Information
Socket Designation: Internal Cache
Configuration: Enabled, Not Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 128 KB
Maximum Size: 128 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000A
DMI type 7, 19 bytes.
Cache Information
Socket Designation: External Cache
Configuration: Enabled, Not Socketed, Level 2
Operational Mode: Write Back
Location: External
Installed Size: 256 KB
Maximum Size: 256 KB
Supported SRAM Types:
Synchronous
Installed SRAM Type: Synchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000B
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: PRIMARY IDE
Internal Connector Type: On Board IDE
External Reference Designator:
External Connector Type: None
Port Type: Other
Handle 0x000C
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: SECONDARY IDE
Internal Connector Type: On Board IDE
External Reference Designator:
External Connector Type: None
Port Type: Other
Handle 0x000D
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: FDD
Internal Connector Type: On Board Floppy
External Reference Designator:
External Connector Type: None
Port Type: 8251 FIFO Compatible
Handle 0x000E
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: COM1
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator:
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x000F
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: COM2
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator:
External Connector Type: DB-9 male
Port Type: Serial Port 16450 Compatible
Handle 0x0010
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: LPT1
Internal Connector Type: DB-25 female
External Reference Designator:
External Connector Type: DB-25 female
Port Type: Parallel Port ECP/EPP
Handle 0x0011
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: Keyboard
Internal Connector Type: PS/2
External Reference Designator:
External Connector Type: PS/2
Port Type: Keyboard Port
Handle 0x0012
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: PS/2 Mouse
Internal Connector Type: PS/2
External Reference Designator:
External Connector Type: PS/2
Port Type: Mouse Port
Handle 0x0013
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI0
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 1
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0014
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI1
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 2
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0015
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI2
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 3
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0016
DMI type 9, 13 bytes.
System Slot Information
Designation: PCI3
Type: 32-bit PCI
Current Usage: Available
Length: Long
ID: 4
Characteristics:
5.0 V is provided
PME signal is supported
Handle 0x0017
DMI type 9, 13 bytes.
System Slot Information
Designation: AGP
Type: 32-bit AGP
Current Usage: Available
Length: Long
ID: 8
Characteristics:
5.0 V is provided
Handle 0x0018
DMI type 8, 9 bytes.
Port Connector Information
Internal Reference Designator: USB
Internal Connector Type: None
External Reference Designator:
External Connector Type: Other
Port Type: USB
Handle 0x0019
DMI type 13, 22 bytes.
BIOS Language Information
Installable Languages: 3
n|US|iso8859-1
n|US|iso8859-1
r|CA|iso8859-1
Currently Installed Language: n|US|iso8859-1
Handle 0x001A
DMI type 16, 15 bytes.
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 768 MB
Error Information Handle: Not Provided
Number Of Devices: 3
Handle 0x001B
DMI type 17, 21 bytes.
Memory Device
Array Handle: 0x001A
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: 512 MB
Form Factor: DIMM
Set: None
Locator: A0
Bank Locator: Bank0/1
Type: Unknown
Type Detail: None
Handle 0x001C
DMI type 17, 21 bytes.
Memory Device
Array Handle: 0x001A
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: 512 MB
Form Factor: DIMM
Set: None
Locator: A1
Bank Locator: Bank2/3
Type: Unknown
Type Detail: None
Handle 0x001D
DMI type 17, 21 bytes.
Memory Device
Array Handle: 0x001A
Error Information Handle: Not Provided
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: A2
Bank Locator: Bank4/5
Type: Unknown
Type Detail: None
Handle 0x001E
DMI type 19, 15 bytes.
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0003FFFFFFF
Range Size: 1 GB
Physical Array Handle: 0x001A
Partition Width: 0
Handle 0x001F
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0001FFFFFFF
Range Size: 512 MB
Physical Device Handle: 0x001B
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0020
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00020000000
Ending Address: 0x0003FFFFFFF
Range Size: 512 MB
Physical Device Handle: 0x001C
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0021
DMI type 20, 19 bytes.
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x000000003FF
Range Size: 1 kB
Physical Device Handle: 0x001D
Memory Array Mapped Address Handle: 0x001E
Partition Row Position: 1
Handle 0x0022
DMI type 32, 11 bytes.
System Boot Information
Status: No errors detected
Handle 0x0023
DMI type 127, 4 bytes.
End Of Table


Nakajima, Jun wrote:

>Following info would be crucial when figuring out the problem.
>In this particular case, it looks like test4 attempted to enable wrong
>PCI interrupt links (i.e. LNKA and LNKD, the ones already enabled).
>
>Thanks,
>Jun
>----
>
>Please file a bug at http://bugzilla.kernel.org/
>Category: Power Management
>Componenet: ACPI
>
>Attach the output from dmidecide, available in /usr/sbin/, or here:
>http://www.nongnu.org/dmidecode/
>
>Attach the output from acpidmp, available in /usr/sbin/, or in here
>http://www.intel.com/technology/iapc/acpi/downloads/pmtools-20010730.tar
>.gz
>
>Attach the dmesg output showing the failure, if possible.
>
>
>
>
>>-----Original Message-----
>>From: Steve French [mailto:smfrench@austin.rr.com]
>>Sent: Sunday, August 24, 2003 9:33 PM
>>To: Jeff Garzik; linux-kernel@vger.kernel.org
>>Subject: Re: via rhine network failure on 2.6.0-test4
>>
>>Looks like IRQ misassignment. Disabling ACPI on test4 got networking
>>
>>
>to
>
>
>>work again and the IRQ assignment is back to IRQ11 for via rhine. The
>>assigned interrupt in the failing case (linux-2.6.0-test4) was IRQ5
>>instead of 11 which presumably it should be - see contents of
>>/proc/interrupts in the failing case (test4):
>>
>>CPU0
>>0: 1013475 XT-PIC timer
>>1: 1309 XT-PIC i8042
>>2: 0 XT-PIC cascade
>>5: 0 XT-PIC eth0
>>9: 0 XT-PIC acpi
>>10: 0 XT-PIC uhci-hcd, uhci-hcd
>>12: 30047 XT-PIC i8042
>>14: 15193 XT-PIC ide0
>>15: 24 XT-PIC ide1
>>NMI: 0
>>ERR: 13
>>
>>The excerpt from the good boot.msg (linux-2.6.0-test3) follows:
>>
>><6>ACPI: Subsystem revision 20030714
>><4> tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully
>>
>>
>acquired
>
>
>><4>Parsing all Control
>>
>>
>>
>Methods:................................................................
>..
>
>
>>................
>><4>Table [DSDT](id F004) - 326 Objects with 29 Devices 82 Methods 21
>>Regions
>><4>ACPI Namespace successfully loaded at root c054f95c
>><4>evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
>><4>evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 15 [_GPE] 2 regs
>>at 0000000000004020 on int 9
>><4>Completing Region/Field/Buffer/Package
>>initialization:..............................................
>><4>Initialized 21/21 Regions 0/0 Fields 15/15 Buffers 10/10 Packages
>>(334 nodes)
>><4>Executing all Device _STA and_INI
>>
>>
>methods:..............................
>
>
>><4>30 Devices found containing: 30 _STA, 1 _INI methods
>><6>ACPI: Interpreter enabled
>><6>ACPI: Using PIC for interrupt routing
>><6>ACPI: PCI Root Bridge [PCI0] (00:00)
>><4>PCI: Probing PCI hardware (bus 00)
>><7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>><4>ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
>><4>ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15,
>>disabled)
>><4>ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15,
>>disabled)
>><4>ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
>><6>Linux Plug and Play Support v0.97 (c) Adam Belay
>><5>SCSI subsystem initialized
>><6>Linux Kernel Card Services 3.1.22
>><6> options: [pci] [pm]
>><6>drivers/usb/core/usb.c: registered new driver usbfs
>><6>drivers/usb/core/usb.c: registered new driver hub
>><4>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
>><4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
>><6>PCI: Using ACPI for IRQ routing
>>
>>
>>The corresponding excerpt from the failing (linux-2.6.0-test4)
>>
>>
>boot.msg
>
>
>><6>ACPI: Subsystem revision 20030813
>><6>ACPI: Interpreter enabled
>><6>ACPI: Using PIC for interrupt routing
>><6>ACPI: PCI Root Bridge [PCI0] (00:00)
>><4>PCI: Probing PCI hardware (bus 00)
>><7>PM: Adding info for No Bus:pci0000:00
>><7>PM: Adding info for pci:0000:00:00.0
>><7>PM: Adding info for pci:0000:00:01.0
>><7>PM: Adding info for pci:0000:00:0e.0
>><7>PM: Adding info for pci:0000:00:11.0
>><7>PM: Adding info for pci:0000:00:11.1
>><7>PM: Adding info for pci:0000:00:11.2
>><7>PM: Adding info for pci:0000:00:11.3
>><7>PM: Adding info for pci:0000:00:12.0
>><7>PM: Adding info for pci:0000:01:00.0
>><7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>><4>ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
>><4>ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15,
>>disabled)
>><4>ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15,
>>disabled)
>><4>ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
>><6>Linux Plug and Play Support v0.97 (c) Adam Belay
>><5>SCSI subsystem initialized
>><6>drivers/usb/core/usb.c: registered new driver usbfs
>><6>drivers/usb/core/usb.c: registered new driver hub
>><4>ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
>><4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
>><6>PCI: Using ACPI for IRQ routing
>>
>>
>>
>>
>>Jeff Garzik wrote:
>>
>>
>>
>>>Steve French wrote:
>>>
>>>
>>>
>>>>The via rhine driver fails to get a dhcp address on my test system
>>>>
>>>>
>on
>
>
>>>>2.6.0-test4. ethereal shows no dhcp request leaving the box but
>>>>ifconfig does show the device and it is detected in /proc/pci.
>>>>Switching from the test3 vs. test4 snapshots built with equivalent
>>>>configure options on the same system (SuSE 8.2) - test3 works but
>>>>test4 does not. This is using essentially the default config for
>>>>
>>>>
>both
>
>
>>>>the test3 and test4 cases - the only changes are SMP disabled, scsi
>>>>devices disabled, Athlon, via-rhine enabled in network devices and
>>>>
>>>>
>a
>
>
>>>>handful of additional filesystems enabled, debug memory allocations
>>>>enabled. This is the first time in many months that I have seen
>>>>problems with the via-rhine driver on 2.6
>>>>
>>>>Analyzing the code differences between 2.6.0-test3 and test4 (in
>>>>via-rhine.c) is not very promising since the only line that has
>>>>changed (kfree to free_netdev) is in the routine
>>>>
>>>>
>via_rhine_remove_one
>
>
>>>>that seems unlikely to cause problems sending data on the network.
>>>>
>>>>Ideas as to what could have caused the regression?
>>>>
>>>>
>>>>
>>>Does /proc/interrupts show any interrupts being received on your eth
>>>device? Does dmesg report any irq assignment problems, or similar?
>>>
>>>This sounds like ACPI or irq routing related.
>>>
>>>Jeff
>>>
>>>
>>>
>>>
>>>
>>>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:48    [W:0.076 / U:4.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site