lkml.org 
[lkml]   [2003]   [Aug]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: How to use an USB<->serial adapter?
Hi,

here's the test programs output and I also set the module option
debug=1 in pl2303.

The testprograms' sources are still in my first mail.

In one terminal I started the listener test, it shows that
it received bytes on ttyS0, tried to write the answer:

$ ./serialtest2 /dev/ttyS0
read: 0x00, written: 0x01
read: 0x01, written: 0x02
read: 0x02, written: 0x03
read: 0x03, written: 0x04
read: 0x04, written: 0x05
read: 0x05, written: 0x06
read: 0x06, written: 0x07
read: 0x07, written: 0x08
read: 0x08, written: 0x09
read: 0x09, written: 0x0a
read: 0x00, written: 0x01
read: 0x01, written: 0x02
read: 0x02, written: 0x03
read: 0x03, written: 0x04
read: 0x04, written: 0x05
read: 0x05, written: 0x06
read: 0x06, written: 0x07
read: 0x07, written: 0x08
read: 0x08, written: 0x09
read: 0x09, written: 0x0a

In another terminal, I started the initiator test twice:

$ ./serialtest1 /dev/usb/ttyUSB0
written: 0x00, read: 0x00 <- sometimes I get one zero byte
written: 0x01, couldn't read
written: 0x02, couldn't read
written: 0x03, couldn't read
written: 0x04, couldn't read
written: 0x05, couldn't read
written: 0x06, couldn't read
written: 0x07, couldn't read
written: 0x08, couldn't read
written: 0x09, couldn't read
$ ./serialtest1 /dev/usb/ttyUSB0
written: 0x00, couldn't read
written: 0x01, couldn't read
written: 0x02, couldn't read
written: 0x03, couldn't read
written: 0x04, couldn't read
written: 0x05, couldn't read
written: 0x06, couldn't read
written: 0x07, couldn't read
written: 0x08, couldn't read
written: 0x09, couldn't read

During the session, the kernel log contains this:

usb.c: USB disconnect on device 00:04.2-2 address 3
pl2303.c: pl2303_shutdown
usbserial.c: PL-2303 converter now disconnected from ttyUSB0
hub.c: new USB device 00:04.2-2, assigned address 4
usbserial.c: PL-2303 converter detected
usbserial.c: PL-2303 converter now attached to ttyUSB0 (or usb/tts/0 for
devfs)
pl2303.c: pl2303_open - port 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0x40:0x1:0x404:0x0 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0xc0:0x1:0x8383:0x0 1 - 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0x40:0x1:0x404:0x1 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0xc0:0x1:0x8383:0x0 1 - 0
pl2303.c: 0x40:0x1:0x0:0x1 0
pl2303.c: 0x40:0x1:0x1:0xc0 0
pl2303.c: 0x40:0x1:0x2:0x4 0
pl2303.c: pl2303_set_termios - port 0, initialized = 0
pl2303.c: 0xa1:0x21:0:0 7 - 0 0 0 0 0 0 0
pl2303.c: 0x40:1:0:1 0
pl2303.c: pl2303_set_termios - data bits = 8
pl2303.c: pl2303_set_termios - baud = 9600
pl2303.c: pl2303_set_termios - stop bits = 1
pl2303.c: pl2303_set_termios - parity = none
pl2303.c: 0x21:0x20:0:0 7
pl2303.c: set_control_lines - value = 3, retval = 0
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: pl2303_open - submitting read urb
pl2303.c: pl2303_open - submitting interrupt urb
pl2303.c: pl2303_ioctl (0) cmd = 0x5401
pl2303.c: pl2303_ioctl not supported = 0x5401
pl2303.c: pl2303_ioctl (0) cmd = 0x540b
pl2303.c: pl2303_ioctl not supported = 0x540b
pl2303.c: pl2303_ioctl (0) cmd = 0x5402
pl2303.c: pl2303_ioctl not supported = 0x5402
pl2303.c: pl2303_set_termios - port 0, initialized = 1
pl2303.c: pl2303_read_int_callback - length = 10, data = a1 20 00 00 00
00 02 00 83 00
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: 0x40:1:0:1 0
pl2303.c: pl2303_set_termios - data bits = 8
pl2303.c: pl2303_set_termios - baud = 115200
pl2303.c: pl2303_set_termios - stop bits = 1
pl2303.c: pl2303_set_termios - parity = none
pl2303.c: 0x21:0x20:0:0 7
pl2303.c: set_control_lines - value = 3, retval = 0
pl2303.c: 0xa1:0x21:0:0 7 - 0 c2 1 0 0 0 8
pl2303.c: pl2303_ioctl (0) cmd = 0x5401
pl2303.c: pl2303_ioctl not supported = 0x5401
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 00
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_read_bulk_callback - port 0
pl2303.c: pl2303_read_bulk_callback - length = 1, data = 00
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 01
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 02
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 03
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 04
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 05
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 06
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 07
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 08
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 09
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_ioctl (0) cmd = 0x540b
pl2303.c: pl2303_ioctl not supported = 0x540b
pl2303.c: pl2303_ioctl (0) cmd = 0x5402
pl2303.c: pl2303_ioctl not supported = 0x5402
pl2303.c: pl2303_set_termios - port 0, initialized = 1
pl2303.c: 0xa1:0x21:0:0 7 - 0 c2 1 0 0 0 8
pl2303.c: 0x40:1:0:1 0
pl2303.c: pl2303_set_termios - data bits = 8
pl2303.c: pl2303_set_termios - baud = 9600
pl2303.c: pl2303_set_termios - stop bits = 1
pl2303.c: pl2303_set_termios - parity = none
pl2303.c: 0x21:0x20:0:0 7
pl2303.c: set_control_lines - value = 3, retval = 0
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: pl2303_ioctl (0) cmd = 0x5401
pl2303.c: pl2303_ioctl not supported = 0x5401
pl2303.c: pl2303_close - port 0
pl2303.c: set_control_lines - value = 0, retval = 0
pl2303.c: pl2303_close - shutting down urbs
pl2303.c: pl2303_close - usb_unlink_urb (write_urb) failed with reason: -19
pl2303.c: pl2303_read_bulk_callback - port 0
pl2303.c: pl2303_read_bulk_callback - urb->status = -2
pl2303.c: pl2303_read_bulk_callback - port is closed, exiting.
pl2303.c: pl2303_open - port 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0x40:0x1:0x404:0x0 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0xc0:0x1:0x8383:0x0 1 - 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0x40:0x1:0x404:0x1 0
pl2303.c: 0xc0:0x1:0x8484:0x0 1 - 0
pl2303.c: 0xc0:0x1:0x8383:0x0 1 - 0
pl2303.c: 0x40:0x1:0x0:0x1 0
pl2303.c: 0x40:0x1:0x1:0xc0 0
pl2303.c: 0x40:0x1:0x2:0x4 0
pl2303.c: pl2303_set_termios - port 0, initialized = 1
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: 0x40:1:0:1 0
pl2303.c: pl2303_set_termios - data bits = 8
pl2303.c: pl2303_set_termios - baud = 9600
pl2303.c: pl2303_set_termios - stop bits = 1
pl2303.c: pl2303_set_termios - parity = none
pl2303.c: 0x21:0x20:0:0 7
pl2303.c: set_control_lines - value = 3, retval = 0
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: pl2303_open - submitting read urb
pl2303.c: pl2303_open - submitting interrupt urb
pl2303.c: pl2303_ioctl (0) cmd = 0x5401
pl2303.c: pl2303_ioctl not supported = 0x5401
pl2303.c: pl2303_ioctl (0) cmd = 0x540b
pl2303.c: pl2303_ioctl not supported = 0x540b
pl2303.c: pl2303_ioctl (0) cmd = 0x5402
pl2303.c: pl2303_ioctl not supported = 0x5402
pl2303.c: pl2303_set_termios - port 0, initialized = 1
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: 0x40:1:0:1 0
pl2303.c: pl2303_set_termios - data bits = 8
pl2303.c: pl2303_set_termios - baud = 115200
pl2303.c: pl2303_set_termios - stop bits = 1
pl2303.c: pl2303_set_termios - parity = none
pl2303.c: 0x21:0x20:0:0 7
pl2303.c: set_control_lines - value = 3, retval = 0
pl2303.c: 0xa1:0x21:0:0 7 - 0 c2 1 0 0 0 8
pl2303.c: pl2303_ioctl (0) cmd = 0x5401
pl2303.c: pl2303_ioctl not supported = 0x5401
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 00
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 01
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 02
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 03
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 04
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 05
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 06
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 07
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 08
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_write - port 0, 1 bytes
pl2303.c: pl2303_write - length = 1, data = 09
pl2303.c: pl2303_write_bulk_callback - port 0
pl2303.c: pl2303_ioctl (0) cmd = 0x540b
pl2303.c: pl2303_ioctl not supported = 0x540b
pl2303.c: pl2303_ioctl (0) cmd = 0x5402
pl2303.c: pl2303_ioctl not supported = 0x5402
pl2303.c: pl2303_set_termios - port 0, initialized = 1
pl2303.c: 0xa1:0x21:0:0 7 - 0 c2 1 0 0 0 8
pl2303.c: 0x40:1:0:1 0
pl2303.c: pl2303_set_termios - data bits = 8
pl2303.c: pl2303_set_termios - baud = 9600
pl2303.c: pl2303_set_termios - stop bits = 1
pl2303.c: pl2303_set_termios - parity = none
pl2303.c: 0x21:0x20:0:0 7
pl2303.c: set_control_lines - value = 3, retval = 0
pl2303.c: 0xa1:0x21:0:0 7 - 80 25 0 0 0 0 8
pl2303.c: pl2303_ioctl (0) cmd = 0x5401
pl2303.c: pl2303_ioctl not supported = 0x5401
pl2303.c: pl2303_close - port 0
pl2303.c: set_control_lines - value = 0, retval = 0
pl2303.c: pl2303_close - shutting down urbs
pl2303.c: pl2303_close - usb_unlink_urb (write_urb) failed with reason: -19
pl2303.c: pl2303_read_bulk_callback - port 0
pl2303.c: pl2303_read_bulk_callback - urb->status = -2
pl2303.c: pl2303_read_bulk_callback - port is closed, exiting.

I also tried some different baud rates (2400, 19200) besides
the fastest 115200 that was default in the testprograms.

Now what?

Oh, did I mention that the pinout of the cable (that I use to loopback
the USB<->serial cable into the same PC) is

DB9 <-> DB9
1,6 <-> 4
2 <-> 3
3 <-> 2
4 <-> 1,6
5 <-> 5
7 <-> 8
8 <-> 7

--
Best regards,
Zoltán Böszörményi

---------------------
What did Hussein say about his knife?
One in Bush worth two in the hand.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:47    [W:0.092 / U:1.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site