lkml.org 
[lkml]   [2003]   [Aug]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [CFT] Clean up yenta_socket
On Tue, 19 Aug 2003, Russell King wrote:

> On Mon, Aug 18, 2003 at 09:31:20PM -0500, Thomas Molina wrote:
> > My laptop is a Presario 12XL325 and I use an SMC 2632W wireless ethernet
> > adapter in the PCMCIA slot.
>
> Thanks. However, it'd help to know the type of your cardbus controller.

here is the lspci output for the cardbus controller on my laptop:

00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus
Controller (rev 01)
Subsystem: Compaq Computer Corporation: Unknown device b103
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 04
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001


Following is the relevant dmesg output during bootup for 2.6.0-test3-mm2
with your patchset applied

PCI: Assigned IRQ 9 for device 0000:00:0a.0
Yenta: CardBus bridge found at 0000:00:0a.0 [0e11:b103]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ list 0018, PCI irq9
Socket status: 30000010
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f
0x378-0x37f 0x388-0x38f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
orinoco.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and others)
orinoco_cs.c 0.13e (David Gibson <hermes@gibson.dropbear.id.au> and
others)
eth0: Station identity 001f:0003:0000:0008
eth0: Looks like an Intersil firmware version 0.8.3
eth0: Ad-hoc demo mode supported
eth0: IEEE standard IBSS ad-hoc mode supported
eth0: WEP supported, 104-bit key
eth0: MAC address 00:04:E2:2A:29:58
eth0: Station name "Prism I"
eth0: ready
eth0: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:47    [W:0.044 / U:6.360 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site