lkml.org 
[lkml]   [2003]   [Jul]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [TRIVIAL] kill surplus menu in IDE Kconfig
Hi,

On Sun, 27 Jul 2003, Tomas Szepe wrote:

> > Moving up BLK_DEV_HD_ONLY like this is probably not a good idea, it makes
> > everything a submenu of this, what might be confusing.
>
> It's logical though. :)

Why? Having it that high in the menu structure, makes it IMO more
important than it actually is.

> > Try the patch below instead, it fixes the menu structure, everything which
> > requires BLK_DEV_IDEDMA_PCI is now also under that menu.
>
> Your patch seems to be against test1 vanilla -- it doesn't apply to -bk3.

Indeed, below is an updated patch.

> > +menuconfig IDE
>
> How exactly does menuconfig work, anyway?
>
> It's not a "block command" -> how will kconf know which entries to put
> in the submenu?
>
> What if I have
>
> menuconfig FOO
> bool "foo"
>
> menuconfig BAR
> bool "bar"
>
> config BAZ
> bool "baz"
> depends on FOO && BAR
>
> Where is BAZ going to show up and why?

kconfig only looks at the previous entry when creating the menu structure,
it does not change the ordering, so BAZ becomes a subentry of BAR.

bye, Roman

diff -ur linux-2.6.0/drivers/ide/Kconfig linux-2.6.0-ide/drivers/ide/Kconfig
--- linux-2.6.0/drivers/ide/Kconfig 2003-07-27 15:20:05.000000000 +0200
+++ linux-2.6.0-ide/drivers/ide/Kconfig 2003-07-27 15:22:23.000000000 +0200
@@ -4,9 +4,7 @@
# Andre Hedrick <andre@linux-ide.org>
#

-menu "ATA/ATAPI/MFM/RLL support"
-
-config IDE
+menuconfig IDE
tristate "ATA/ATAPI/MFM/RLL support"
---help---
If you say Y here, your kernel will be able to manage low cost mass
@@ -52,21 +50,19 @@

If unsure, say Y.

+if IDE
+
config IDE_MAX_HWIFS
int "Max IDE interfaces"
- depends on ALPHA && IDE
+ depends on ALPHA
default 4
help
This is the maximum number of IDE hardware interfaces that will
be supported by the driver. Make sure it is at least as high as
the number of IDE interfaces in your system.

-menu "IDE, ATA and ATAPI Block devices"
- depends on IDE!=n
-
config BLK_DEV_IDE
tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support"
- depends on IDE
---help---
If you say Y here, you will use the full-featured IDE driver to
control up to ten ATA/IDE interfaces, each being able to serve a
@@ -95,13 +91,15 @@
If you have one or more IDE drives, say Y or M here. If your system
has no IDE drives, or if memory requirements are really tight, you
could say N here, and select the "Old hard disk driver" below
- instead to save about 13 KB of memory in the kernel.
+ instead to save about 60 KB of memory in the kernel.
+
+if BLK_DEV_IDE

comment "Please see Documentation/ide.txt for help/info on IDE drives"

config BLK_DEV_HD_IDE
bool "Use old disk-only driver on primary interface"
- depends on BLK_DEV_IDE && X86 && X86_PC9800!=y
+ depends on X86 && X86_PC9800!=y
---help---
There are two drivers for MFM/RLL/IDE disks. Most people use just
the new enhanced driver by itself. This option however installs the
@@ -119,7 +117,7 @@

config BLK_DEV_HD_IDE98
bool "Use old disk-only driver on primary interface"
- depends on BLK_DEV_IDE && X86 && X86_PC9800
+ depends on X86 && X86_PC9800
---help---
There are two drivers for MFM/RLL/IDE disks. Most people use just
the new enhanced driver by itself. This option however installs the
@@ -135,14 +133,8 @@
Normally, just say N here; you will then use the new driver for all
4 interfaces.

-config BLK_DEV_HD
- bool
- default BLK_DEV_HD_ONLY if BLK_DEV_IDE=n
- default BLK_DEV_HD_IDE if BLK_DEV_IDE
-
config BLK_DEV_IDEDISK
tristate "Include IDE/ATA-2 DISK support"
- depends on BLK_DEV_IDE
---help---
This will include enhanced support for MFM/RLL/IDE hard disks. If
you have a MFM/RLL/IDE disk, and there is no special reason to use
@@ -183,14 +175,13 @@

config BLK_DEV_IDECS
tristate "PCMCIA IDE support"
- depends on BLK_DEV_IDE && PCMCIA
+ depends on PCMCIA
help
Support for outboard IDE disks, tape drives, and CD-ROM drives
connected through a PCMCIA card.

config BLK_DEV_IDECD
tristate "Include IDE/ATAPI CDROM support"
- depends on BLK_DEV_IDE
---help---
If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
@@ -216,7 +207,6 @@
#dep_tristate ' Include IDE/ATAPI TAPE support' CONFIG_BLK_DEV_IDETAPE $CONFIG_BLK_DEV_IDE
config BLK_DEV_IDEFLOPPY
tristate "Include IDE/ATAPI FLOPPY support"
- depends on BLK_DEV_IDE
---help---
If you have an IDE floppy drive which uses the ATAPI protocol,
answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
@@ -241,7 +231,7 @@

config BLK_DEV_IDESCSI
tristate "SCSI emulation support"
- depends on BLK_DEV_IDE && SCSI
+ depends on SCSI
---help---
This will provide SCSI host adapter emulation for IDE ATAPI devices,
and will allow you to use a SCSI device driver instead of a native
@@ -267,7 +257,6 @@

config IDE_TASK_IOCTL
bool "IDE Taskfile Access"
- depends on BLK_DEV_IDE
help
This is a direct raw access to the media. It is a complex but
elegant solution to test and validate the domain of the hardware and
@@ -278,19 +267,17 @@

config IDE_TASKFILE_IO
bool 'IDE Taskfile IO (EXPERIMENTAL)'
- depends on BLK_DEV_IDE && EXPERIMENTAL
- default n
+ depends on EXPERIMENTAL
---help---
Use new taskfile IO code.

It is safe to say Y to this question, in most cases.

comment "IDE chipset support/bugfixes"
- depends on BLK_DEV_IDE

config BLK_DEV_CMD640
bool "CMD640 chipset bugfix/support"
- depends on BLK_DEV_IDE && X86
+ depends on X86
---help---
The CMD-Technologies CMD640 IDE chip is used on many common 486 and
Pentium motherboards, usually in combination with a "Neptune" or
@@ -324,7 +311,7 @@

config BLK_DEV_IDEPNP
bool "PNP EIDE support"
- depends on BLK_DEV_IDE && PNP
+ depends on PNP
help
If you have a PnP (Plug and Play) compatible EIDE card and
would like the kernel to automatically detect and activate
@@ -332,8 +319,7 @@

config BLK_DEV_IDEPCI
bool "PCI IDE chipset support" if PCI
- depends on BLK_DEV_IDE
- default BLK_DEV_IDEDMA_PMAC if PPC_PMAC && BLK_DEV_IDEDMA_PMAC
+ default BLK_DEV_IDEDMA_PMAC if PPC_PMAC
help
Say Y here for PCI systems which use IDE drive(s).
This option helps the IDE driver to automatically detect and
@@ -414,29 +400,6 @@
You probably just want the default of 32 here. If you enter an invalid
number, the default value will be used.

-config BLK_DEV_OFFBOARD
- bool "Boot off-board chipsets first support"
- depends on PCI && BLK_DEV_IDEPCI
- ---help---
- Normally, IDE controllers built into the motherboard (on-board
- controllers) are assigned to ide0 and ide1 while those on add-in PCI
- cards (off-board controllers) are relegated to ide2 and ide3.
- Answering Y here will allow you to reverse the situation, with
- off-board controllers on ide0/1 and on-board controllers on ide2/3.
- This can improve the usability of some boot managers such as lilo
- when booting from a drive on an off-board controller.
-
- If you say Y here, and you actually want to reverse the device scan
- order as explained above, you also need to issue the kernel command
- line option "ide=reverse". (Try "man bootparam" or see the
- documentation of your boot loader (lilo or loadlin) about how to
- pass options to the kernel at boot time.)
-
- Note that, if you do this, the order of the hd* devices will be
- rearranged which may require modification of fstab and other files.
-
- If in doubt, say N.
-
config BLK_DEV_IDEDMA_FORCED
bool "Force enable legacy 2.0.X HOSTS to use DMA"
depends on BLK_DEV_IDEDMA_PCI
@@ -470,13 +433,6 @@

Generally say N here.

-config BLK_DEV_IDEDMA
- bool
- depends on BLK_DEV_IDE
- default BLK_DEV_IDEDMA_ICS if ARCH_ACORN
- default BLK_DEV_IDEDMA_PMAC if PPC_PMAC && BLK_DEV_IDE_PMAC
- default BLK_DEV_IDEDMA_PCI if PCI && BLK_DEV_IDEPCI
-
config IDEDMA_PCI_WIP
bool "ATA Work(s) In Progress (EXPERIMENTAL)"
depends on BLK_DEV_IDEDMA_PCI && EXPERIMENTAL
@@ -498,11 +454,6 @@

If in doubt, say N.

-config BLK_DEV_ADMA
- bool
- depends on PCI && BLK_DEV_IDEPCI
- default BLK_DEV_IDEDMA_PCI
-
config BLK_DEV_AEC62XX
tristate "AEC62XX chipset support"
depends on BLK_DEV_IDEDMA_PCI
@@ -585,7 +536,7 @@

config BLK_DEV_CS5530
tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support"
- depends on BLK_DEV_IDEDMA_PCIOA
+ depends on BLK_DEV_IDEDMA_PCI
help
Include support for UDMA on the Cyrix MediaGX 5530 chipset. This
will automatically be detected and configured if found.
@@ -672,13 +623,6 @@

Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>.

-config BLK_DEV_OPTI621
- tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
- depends on PCI && BLK_DEV_IDEPCI && EXPERIMENTAL
- help
- This is a driver for the OPTi 82C621 EIDE controller.
- Please read the comments at the top of <file:drivers/ide/pci/opti621.c>.
-
config BLK_DEV_PDC202XX_OLD
tristate "PROMISE PDC202{46|62|65|67} support"
depends on BLK_DEV_IDEDMA_PCI
@@ -711,18 +655,6 @@
help
For FastTrak enable overriding BIOS.

-config BLK_DEV_RZ1000
- tristate "RZ1000 chipset bugfix/support"
- depends on PCI && BLK_DEV_IDEPCI && X86
- help
- The PC-Technologies RZ1000 IDE chip is used on many common 486 and
- Pentium motherboards, usually along with the "Neptune" chipset.
- Unfortunately, it has a rather nasty design flaw that can cause
- severe data corruption under many conditions. Say Y here to include
- code which automatically detects and corrects the problem under
- Linux. This may slow disk throughput by a few percent, but at least
- things will operate 100% reliably.
-
config BLK_DEV_SVWKS
tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
depends on BLK_DEV_IDEDMA_PCI
@@ -789,6 +721,32 @@
This allows the kernel to change PIO, DMA and UDMA speeds and to
configure the chip to optimum performance.

+config BLK_DEV_PDC202XX
+ bool
+ depends on BLK_DEV_IDEDMA_PCI && (BLK_DEV_PDC202XX_OLD || BLK_DEV_PDC202XX_NEW)
+ default y
+ ---help---
+ Promise Ultra33 or PDC20246
+ Promise Ultra66 or PDC20262
+ Promise Ultra100 or PDC20265/PDC20267/PDC20268
+
+ This driver adds up to 4 more EIDE devices sharing a single
+ interrupt. This add-on card is a bootable PCI UDMA controller. Since
+ multiple cards can be installed and there are BIOS ROM problems that
+ happen if the BIOS revisions of all installed cards (three-max) do
+ not match, the driver attempts to do dynamic tuning of the chipset
+ at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
+ for more than one card. This card may require that you say Y to
+ "Special UDMA Feature".
+
+ If you say Y here, you need to say Y to "Use DMA by default when
+ available" as well.
+
+ Please read the comments at the top of
+ <file:drivers/ide/pdc202xx_old.c>.
+
+ If unsure, say N.
+
config BLK_DEV_SL82C105
tristate "Winbond SL82c105 support"
depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
@@ -797,9 +755,56 @@
special configuration for this chip. This is common on various CHRP
motherboards, but could be used elsewhere. If in doubt, say Y.

+config BLK_DEV_ADMA
+ bool
+ depends on PCI && BLK_DEV_IDEPCI
+ default BLK_DEV_IDEDMA_PCI
+
+config BLK_DEV_OPTI621
+ tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
+ depends on PCI && BLK_DEV_IDEPCI && EXPERIMENTAL
+ help
+ This is a driver for the OPTi 82C621 EIDE controller.
+ Please read the comments at the top of <file:drivers/ide/pci/opti621.c>.
+
+config BLK_DEV_RZ1000
+ tristate "RZ1000 chipset bugfix/support"
+ depends on PCI && BLK_DEV_IDEPCI && X86
+ help
+ The PC-Technologies RZ1000 IDE chip is used on many common 486 and
+ Pentium motherboards, usually along with the "Neptune" chipset.
+ Unfortunately, it has a rather nasty design flaw that can cause
+ severe data corruption under many conditions. Say Y here to include
+ code which automatically detects and corrects the problem under
+ Linux. This may slow disk throughput by a few percent, but at least
+ things will operate 100% reliably.
+
+config BLK_DEV_OFFBOARD
+ bool "Boot off-board chipsets first support"
+ depends on PCI && BLK_DEV_IDEPCI
+ ---help---
+ Normally, IDE controllers built into the motherboard (on-board
+ controllers) are assigned to ide0 and ide1 while those on add-in PCI
+ cards (off-board controllers) are relegated to ide2 and ide3.
+ Answering Y here will allow you to reverse the situation, with
+ off-board controllers on ide0/1 and on-board controllers on ide2/3.
+ This can improve the usability of some boot managers such as lilo
+ when booting from a drive on an off-board controller.
+
+ If you say Y here, and you actually want to reverse the device scan
+ order as explained above, you also need to issue the kernel command
+ line option "ide=reverse". (Try "man bootparam" or see the
+ documentation of your boot loader (lilo or loadlin) about how to
+ pass options to the kernel at boot time.)
+
+ Note that, if you do this, the order of the hd* devices will be
+ rearranged which may require modification of fstab and other files.
+
+ If in doubt, say N.
+
config BLK_DEV_IDE_PMAC
bool "Builtin PowerMac IDE support"
- depends on BLK_DEV_IDE && PPC_PMAC
+ depends on PPC_PMAC
help
This driver provides support for the built-in IDE controller on
most of the recent Apple Power Macintoshes and PowerBooks.
@@ -827,11 +832,11 @@

config BLK_DEV_IDE_SWARM
bool "SWARM onboard IDE support"
- depends on BLK_DEV_IDE && SIBYTE_SWARM
+ depends on SIBYTE_SWARM

config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
- depends on BLK_DEV_IDE!=n && ARM && ARCH_ACORN
+ depends on ARM && ARCH_ACORN
help
On Acorn systems, say Y here if you wish to use the ICS IDE
interface card. This is not required for ICS partition support.
@@ -857,16 +862,32 @@
If you suspect your hardware is at all flakey, say N here.
Do NOT email the IDE kernel people regarding this issue!

+config IDEDMA_IVB
+ bool "IGNORE word93 Validation BITS"
+ depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
+ ---help---
+ There are unclear terms in ATA-4 and ATA-5 standards how certain
+ hardware (an 80c ribbon) should be detected. Different interpretations
+ of the standards have been released in hardware. This causes problems:
+ for example, a host with Ultra Mode 4 (or higher) will not run
+ in that mode with an 80c ribbon.
+
+ If you are experiencing compatibility or performance problems, you
+ MAY try to answering Y here. However, it does not necessarily solve
+ any of your problems, it could even cause more of them.
+
+ It is normally safe to answer Y; however, the default is N.
+
config BLK_DEV_IDE_RAPIDE
tristate "RapIDE interface support"
- depends on BLK_DEV_IDE!=n && ARM && ARCH_ACORN
+ depends on ARM && ARCH_ACORN
help
Say Y here if you want to support the Yellowstone RapIDE controller
manufactured for use with Acorn computers.

config BLK_DEV_GAYLE
bool "Amiga Gayle IDE interface support"
- depends on BLK_DEV_IDE && AMIGA
+ depends on AMIGA
help
This is the IDE driver for the builtin IDE interface on some Amiga
models. It supports both the `A1200 style' (used in A600 and A1200)
@@ -893,7 +914,7 @@

config BLK_DEV_BUDDHA
bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
- depends on BLK_DEV_IDE && ZORRO && EXPERIMENTAL
+ depends on ZORRO && EXPERIMENTAL
help
This is the IDE driver for the IDE interfaces on the Buddha,
Catweasel and X-Surf expansion boards. It supports up to two interfaces
@@ -905,7 +926,7 @@

config BLK_DEV_FALCON_IDE
bool "Falcon IDE interface support"
- depends on BLK_DEV_IDE && ATARI
+ depends on ATARI
help
This is the IDE driver for the builtin IDE interface on the Atari
Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
@@ -914,7 +935,7 @@

config BLK_DEV_MAC_IDE
bool "Macintosh Quadra/Powerbook IDE interface support"
- depends on BLK_DEV_IDE && MAC
+ depends on MAC
help
This is the IDE driver for the builtin IDE interface on some m68k
Macintosh models. It supports both the `Quadra style' (used in
@@ -927,7 +948,7 @@

config BLK_DEV_Q40IDE
bool "Q40/Q60 IDE interface support"
- depends on BLK_DEV_IDE && Q40
+ depends on Q40
help
Enable the on-board IDE controller in the Q40/Q60. This should
normally be on; disable it only if you are running a custom hard
@@ -935,7 +956,7 @@

config BLK_DEV_MPC8xx_IDE
bool "MPC8xx IDE support"
- depends on BLK_DEV_IDE && 8xx
+ depends on 8xx
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
@@ -975,7 +996,7 @@
# no isa -> no vlb
config IDE_CHIPSETS
bool "Other IDE chipset support"
- depends on BLK_DEV_IDE && ISA
+ depends on ISA
---help---
Say Y here if you want to include enhanced support for various IDE
interface chipsets used on motherboards and add-on cards. You can
@@ -990,7 +1011,7 @@
People with SCSI-only systems can say N here.

comment "Note: most of these also require special kernel boot parameters"
- depends on BLK_DEV_IDE && IDE_CHIPSETS
+ depends on IDE_CHIPSETS

config BLK_DEV_4DRIVES
bool "Generic 4 drives/port support"
@@ -1004,7 +1025,7 @@

config BLK_DEV_ALI14XX
tristate "ALI M14xx support"
- depends on IDE_CHIPSETS && BLK_DEV_IDE
+ depends on IDE_CHIPSETS
help
This driver is enabled at runtime using the "ide0=ali14xx" kernel
boot parameter. It enables support for the secondary IDE interface
@@ -1015,7 +1036,7 @@

config BLK_DEV_DTC2278
tristate "DTC-2278 support"
- depends on IDE_CHIPSETS && BLK_DEV_IDE
+ depends on IDE_CHIPSETS
help
This driver is enabled at runtime using the "ide0=dtc2278" kernel
boot parameter. It enables support for the secondary IDE interface
@@ -1025,7 +1046,7 @@

config BLK_DEV_HT6560B
tristate "Holtek HT6560B support"
- depends on IDE_CHIPSETS && BLK_DEV_IDE
+ depends on IDE_CHIPSETS
help
This driver is enabled at runtime using the "ide0=ht6560b" kernel
boot parameter. It enables support for the secondary IDE interface
@@ -1048,7 +1069,7 @@

config BLK_DEV_QD65XX
tristate "QDI QD65xx support"
- depends on IDE_CHIPSETS && BLK_DEV_IDE
+ depends on IDE_CHIPSETS
help
This driver is enabled at runtime using the "ide0=qd65xx" kernel
boot parameter. It permits faster I/O speeds to be set. See the
@@ -1057,7 +1078,7 @@

config BLK_DEV_UMC8672
tristate "UMC-8672 support"
- depends on IDE_CHIPSETS && BLK_DEV_IDE
+ depends on IDE_CHIPSETS
help
This driver is enabled at runtime using the "ide0=umc8672" kernel
boot parameter. It enables support for the secondary IDE interface
@@ -1065,6 +1086,8 @@
See the files <file:Documentation/ide.txt> and
<file:drivers/ide/legacy/umc8672.c> for more info.

+endif
+
config BLK_DEV_HD_ONLY
bool "Old hard disk (MFM/RLL/IDE) driver"
depends on BLK_DEV_IDE=n
@@ -1077,70 +1100,35 @@
since it lacks the enhanced functionality of the new one. This makes
it a good choice for systems with very tight memory restrictions, or
for systems with only older MFM/RLL/ESDI drives. Choosing the old
- driver can save 13 KB or so of kernel memory.
+ driver can save 60 KB or so of kernel memory.

If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
instead of this one. For more detailed information, read the
Disk-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.

-config IDEDMA_AUTO
- bool
- depends on IDEDMA_PCI_AUTO || BLK_DEV_IDEDMA_PMAC_AUTO || IDEDMA_ICS_AUTO
- default y
-
-config IDEDMA_IVB
- bool "IGNORE word93 Validation BITS"
- depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
- ---help---
- There are unclear terms in ATA-4 and ATA-5 standards how certain
- hardware (an 80c ribbon) should be detected. Different interpretations
- of the standards have been released in hardware. This causes problems:
- for example, a host with Ultra Mode 4 (or higher) will not run
- in that mode with an 80c ribbon.
+config BLK_DEV_HD
+ def_bool BLK_DEV_HD_ONLY || BLK_DEV_HD_IDE

- If you are experiencing compatibility or performance problems, you
- MAY try to answering Y here. However, it does not necessarily solve
- any of your problems, it could even cause more of them.
+config BLK_DEV_IDEDMA
+ def_bool BLK_DEV_IDEDMA_ICS || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_PCI

- It is normally safe to answer Y; however, the default is N.
+config IDEDMA_AUTO
+ def_bool IDEDMA_PCI_AUTO || BLK_DEV_IDEDMA_PMAC_AUTO || IDEDMA_ICS_AUTO

config DMA_NONPCI
- bool
- depends on BLK_DEV_TIVO
- default y
-
-config BLK_DEV_PDC202XX
- bool
- depends on BLK_DEV_IDEDMA_PCI && (BLK_DEV_PDC202XX_OLD || BLK_DEV_PDC202XX_NEW)
- default y
- ---help---
- Promise Ultra33 or PDC20246
- Promise Ultra66 or PDC20262
- Promise Ultra100 or PDC20265/PDC20267/PDC20268
-
- This driver adds up to 4 more EIDE devices sharing a single
- interrupt. This add-on card is a bootable PCI UDMA controller. Since
- multiple cards can be installed and there are BIOS ROM problems that
- happen if the BIOS revisions of all installed cards (three-max) do
- not match, the driver attempts to do dynamic tuning of the chipset
- at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
- for more than one card. This card may require that you say Y to
- "Special UDMA Feature".
-
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
-
- Please read the comments at the top of
- <file:drivers/ide/pdc202xx_old.c>.
-
- If unsure, say N.
+ def_bool BLK_DEV_TIVO

config BLK_DEV_IDE_MODES
- bool
- depends on BLK_DEV_4DRIVES || BLK_DEV_ALI14XX || BLK_DEV_DTC2278 || BLK_DEV_HT6560B || BLK_DEV_PDC4030 || BLK_DEV_QD65XX || BLK_DEV_UMC8672 || BLK_DEV_AEC62XX=y || BLK_DEV_ALI15X3=y || BLK_DEV_AMD74XX=y || BLK_DEV_CMD640 || BLK_DEV_CMD64X=y || BLK_DEV_CS5530=y || BLK_DEV_CY82C693=y || BLK_DEV_HPT34X=y || BLK_DEV_HPT366=y || BLK_DEV_IDE_PMAC || BLK_DEV_IT8172 || BLK_DEV_MPC8xx_IDE || BLK_DEV_NFORCE=y || BLK_DEV_OPTI621=y || BLK_DEV_PDC202XX || BLK_DEV_PIIX=y || BLK_DEV_SVWKS=y || BLK_DEV_SIIMAGE=y || BLK_DEV_SIS5513=y || BLK_DEV_SL82C105=y || BLK_DEV_SLC90E66=y || BLK_DEV_VIA82CXXX=y
- default y
-
-endmenu
+ def_bool BLK_DEV_4DRIVES || BLK_DEV_ALI14XX || BLK_DEV_DTC2278 || \
+ BLK_DEV_HT6560B || BLK_DEV_PDC4030 || BLK_DEV_QD65XX || \
+ BLK_DEV_UMC8672 || BLK_DEV_AEC62XX=y || BLK_DEV_ALI15X3=y || \
+ BLK_DEV_AMD74XX=y || BLK_DEV_CMD640 || BLK_DEV_CMD64X=y || \
+ BLK_DEV_CS5530=y || BLK_DEV_CY82C693=y || BLK_DEV_HPT34X=y || \
+ BLK_DEV_HPT366=y || BLK_DEV_IDE_PMAC || BLK_DEV_IT8172 || \
+ BLK_DEV_MPC8xx_IDE || BLK_DEV_NFORCE=y || BLK_DEV_OPTI621=y || \
+ BLK_DEV_PDC202XX || BLK_DEV_PIIX=y || BLK_DEV_SVWKS=y || \
+ BLK_DEV_SIIMAGE=y || BLK_DEV_SIS5513=y || BLK_DEV_SL82C105=y || \
+ BLK_DEV_SLC90E66=y || BLK_DEV_VIA82CXXX=y

-endmenu
+endif
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:47    [from the cache]
©2003-2014 Jasper Spaans. hosted at Digital Ocean