Messages in this thread | | | Date | Fri, 30 May 2003 11:57:48 -0700 (PDT) | From | <> | Subject | Re: siimage driver status |
| |
> On Iau, 2003-05-29 at 16:00, Wm. Josiah Erikson wrote: > > Wow. I feel dumb. When I add the -X66 to tell the drive as well, then > > everything is peachy. Thanks! :) > > Its hardly obvious. > > > Now I suppose I just have to figure out how to make that work on boot > > (perhaps just to make the BIOS put them in DMA mode) > > One thing I might do is just make the driver ignore the bios policy for > disk devices.
I reinstalled my SiImage controller this morning because I hadn't documented using the -X66 switch during my previous testing. It actually makes a bit of a difference- the DMA enables and THEN the machine locks hard when any reasonable amount of data is written to the drives on the controller.
I get two console messages before the machine locks hard: hde: dma_timer_expiry: dma status == 0x22 hde: dma_timer_expiry status = 0xd8 { Busy }
I'd love to get this tracked down...
Brian.
-----------------------
from /var/log/messages
May 30 11:34:38 nfs2 kernel: SiI3112 Serial ATA: IDE controller at PCI slot 05:02.0 May 30 11:34:38 nfs2 kernel: SiI3112 Serial ATA: chipset revision 2 May 30 11:34:38 nfs2 kernel: SiI3112 Serial ATA: not 100%% native mode: will probe irqs later May 30 11:34:38 nfs2 kernel: ide2: MMIO-DMA , BIOS settings: hde:pio, hdf:pio May 30 11:34:38 nfs2 kernel: ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
---- hdparm -X66 -d1 /dev/hde hdparm -X66 -d1 /dev/hdg
[root@nfs2 settings]# cat /proc/ide/siimage Controller: 0 SiI3112 Chipset. MMIO Base 0xf880d000 MMIO-DMA Base 0xf880d000 MMIO-DMA Base 0xf880d008 --------------- Primary Channel ---------------- Secondary Channel ------------- --------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------ PIO Mode: ? ? ? ?
hdparm -I /dev/hde
/dev/hde:
ATA device, with non-removable media Model Number: Maxtor 6Y200P0 Serial Number: Yv0AXR8E Firmware Revision: YAR41VW0 Standards: Supported: 7 6 5 4 Likely used: 7 Configuration: Logical max current cylinders 16383 65535 heads 16 1 sectors/track 63 63 -- CHS current addressable sectors: 4128705 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 402622464 device size with M = 1024*1024: 196593 MBytes device size with M = 1000*1000: 206142 MBytes (206 GB) Capabilities: LBA, IORDY(can be disabled) Queue depth: 1 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 192, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5 udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * NOP cmd * READ BUFFER cmd * WRITE BUFFER cmd * Host Protected Area feature set * Look-ahead * Write cache * Power Management feature set Security Mode feature set * SMART feature set * FLUSH CACHE EXT command * Mandatory FLUSH CACHE command * Device Configuration Overlay feature set * 48-bit Address feature set * Automatic Acoustic Management feature set SET MAX security extension Advanced Power Management feature set * DOWNLOAD MICROCODE cmd * SMART self-test * SMART error logging Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase HW reset results: CBLID- above Vih Device num = 0 determined by the jumper
/proc/cpuinfo
processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 7 cpu MHz : 2399.366 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 4784.12
processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 7 cpu MHz : 2399.366 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 4797.23
processor : 2 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 7 cpu MHz : 2399.366 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 4797.23
processor : 3 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Xeon(TM) CPU 2.40GHz stepping : 7 cpu MHz : 2399.366 cache size : 512 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm bogomips : 4797.23
lspci -vvv
00:00.0 Host bridge: Intel Corp.: Unknown device 254c (rev 01) Subsystem: Super Micro Computer Inc: Unknown device 3480 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [40] #09 [1105]
00:00.1 Class ff00: Intel Corp. e7500 [Plumas] DRAM Controller Error Reporting (rev 01) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:02.0 PCI bridge: Intel Corp. e7500 [Plumas] HI_B Virtual PCI Bridge (F0) (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=01, subordinate=03, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: fc100000-fc2fffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:03.0 PCI bridge: Intel Corp. e7500 [Plumas] HI_C Virtual PCI Bridge (F0) (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Bus: primary=00, secondary=04, subordinate=06, sec-latency=0 I/O behind bridge: 00004000-00005fff Memory behind bridge: fc300000-fcffffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at 2000 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02) (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 2020 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02) (prog-if 00 [UHCI]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 2040 [size=32]
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 42) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=64 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd000000-fe0fffff Prefetchable memory behind bridge: fff00000-000fffff BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801CA ISA Bridge (LPC) (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801CA IDE U100 (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 0 Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <ignored> Region 3: I/O ports at <ignored> Region 4: I/O ports at 2060 [size=16] Region 5: Memory at 80000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus (rev 02) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed to IRQ 0 Region 4: I/O ports at 1100 [size=32]
01:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if 20 [IO(X)-APIC]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at fc100000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] PCI-X non-bridge device. Command: DPERE- ERO- RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 01:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 10 Bus: primary=01, secondary=02, subordinate=02, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B- Capabilities: [50] PCI-X non-bridge device. Command: DPERE+ ERO+ RBC=0 OST=4 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 01:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if 20 [IO(X)-APIC]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at fc101000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] PCI-X non-bridge device. Command: DPERE- ERO- RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 01:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 10 Bus: primary=01, secondary=03, subordinate=03, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: fc200000-fc2fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B- Capabilities: [50] PCI-X non-bridge device. Command: DPERE+ ERO+ RBC=0 OST=4 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 03:02.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01) Subsystem: Intel Corp. PRO/1000 MT Dual Port Server Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (63750ns min), cache line size 08 Interrupt: pin A routed to IRQ 28 Region 0: Memory at fc200000 (64-bit, non-prefetchable) [size=128K] Region 4: I/O ports at 3000 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device. Command: DPERE- ERO+ RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000
03:02.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01) Subsystem: Intel Corp. PRO/1000 MT Dual Port Server Adapter Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (63750ns min), cache line size 08 Interrupt: pin B routed to IRQ 29 Region 0: Memory at fc220000 (64-bit, non-prefetchable) [size=128K] Region 4: I/O ports at 3040 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device. Command: DPERE- ERO+ RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000
04:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if 20 [IO(X)-APIC]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at fc300000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] PCI-X non-bridge device. Command: DPERE- ERO- RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 04:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 10 Bus: primary=04, secondary=05, subordinate=05, sec-latency=48 I/O behind bridge: 00004000-00004fff Memory behind bridge: fc400000-fc4fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B- Capabilities: [50] PCI-X non-bridge device. Command: DPERE+ ERO+ RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 04:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04) (prog-if 20 [IO(X)-APIC]) Subsystem: Super Micro Computer Inc P4DP6 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at fc301000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] PCI-X non-bridge device. Command: DPERE- ERO- RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 04:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 10 Bus: primary=04, secondary=06, subordinate=06, sec-latency=48 I/O behind bridge: 00005000-00005fff Memory behind bridge: fc500000-fcffffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B- Capabilities: [50] PCI-X non-bridge device. Command: DPERE+ ERO+ RBC=0 OST=0 Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- 05:02.0 RAID bus controller: CMD Technology Inc Silicon Image SiI 3112 SATARaid Controller (rev 02) Subsystem: CMD Technology Inc: Unknown device 6112 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 01 Interrupt: pin A routed to IRQ 100 Region 0: I/O ports at 4020 [size=8] Region 1: I/O ports at 4010 [size=4] Region 2: I/O ports at 4018 [size=8] Region 3: I/O ports at 4014 [size=4] Region 4: I/O ports at 4000 [size=16] Region 5: Memory at fc400000 (32-bit, non-prefetchable) [size=512] Expansion ROM at <unassigned> [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
07:01.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA]) Subsystem: ATI Technologies Inc Rage XL Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min), cache line size 08 Interrupt: pin A routed to IRQ 16 Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 6000 [size=256] Region 2: Memory at fe000000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [5c] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |