Messages in this thread Patch in this message | | | Date | Sat, 10 May 2003 14:18:16 +0200 | From | Adrian Bunk <> | Subject | [2.4 patch] Configure.help updates from -ac |
| |
Hi Marcelo,
the patch below includes some Configure.help entries for new options in 2.4.21 that aren't in 2.4.21-rc2 from -ac.
It applies (with a few lines offset) against 2.4.21-rc2.
Please apply Adrian
--- linux.21rc1/Documentation/Configure.help 2003-04-22 16:39:32.000000000 +0100 +++ linux.21rc1-ac4/Documentation/Configure.help 2003-05-03 19:08:44.000000000 +0100 @@ -23168,6 +23545,23 @@ say M here and read <file:Documentation/modules.txt>. The module will be called radio-sf16fmi.o. +SF16FMR2 Radio +CONFIG_RADIO_SF16FMR2 + Choose Y here if you have one of these FM radio cards. If you + compile the driver into the kernel and your card is not PnP one, you + have to add "sf16fmr2=<io>" to the kernel command line (I/O address is + 0x284 or 0x384, default 0x384). + + In order to control your radio card, you will need to use programs + that are compatible with the Video For Linux API. Information on + this API and pointers to "v4l" programs may be found on the WWW at + <http://roadrunner.swansea.uk.linux.org/v4l.shtml>. + + If you want to compile this driver as a module ( = code which can be + inserted in and removed from the running kernel whenever you want), + say M here and read <file:Documentation/modules.txt>. The module + will be called radio-sf16fmr2.o. + Typhoon Radio (a.k.a. EcoRadio) CONFIG_RADIO_TYPHOON Choose Y here if you have one of these FM radio cards, and then fill @@ -26523,6 +27038,90 @@ If unsure, say N. +NatSemi SCx200 support +CONFIG_SCx200 + This provides basic support for the National Semiconductor SCx200 + processor. Right now this is just a driver for the GPIO pins. + + If you don't know what to do here, say N. + + This support is also available as a module. If compiled as a + module, it will be called scx200.o. + +NatSemi SCx200 Watchdog +CONFIG_SCx200_WDT + Enable the built-in watchdog timer support on the National + Semiconductor SCx200 processors. + + If compiled as a module, it will be called scx200_watchdog.o. + +Flash device mapped with DOCCS on NatSemi SCx200 +CONFIG_MTD_SCx200_DOCFLASH + Enable support for a flash chip mapped using the DOCCS signal on a + National Semiconductor SCx200 processor. + + If you don't know what to do here, say N. + + If compiled as a module, it will be called scx200_docflash.o. + +NatSemi SCx200 I2C using GPIO pins +CONFIG_SCx200_GPIO + Enable the use of two GPIO pins of a SCx200 processor as an I2C bus. + + If you don't know what to do here, say N. + + If compiled as a module, it will be called scx200_i2c.o. + +GPIO pin used for SCL +CONFIG_SCx200_I2C_SCL + Enter the GPIO pin number used for the SCL signal. This value can + also be specified with a module parameter. + +GPIO pin used for SDA +CONFIG_SCx200_I2C_SDA + Enter the GPIO pin number used for the SSA signal. This value can + also be specified with a module parameter. + +NatSemi SCx200 ACCESS.bus +CONFIG_SCx200_ACB + Enable the use of the ACCESS.bus controllers of a SCx200 processor. + + If you don't know what to do here, say N. + + If compiled as a module, it will be called scx200_acb.o. + +IPMI top-level message handler +CONFIG_IPMI_HANDLER + This enables the central IPMI message handler, required for IPMI + to work. Note that you must have this enabled to do any other IPMI + things. + + IPMI is a standard for managing sensors (temperature, + voltage, etc.) in a system. + + See Documentation/IPMI.txt for more details on the driver. + + If unsure, say N. + +Generate a panic event to all BMCs on a panic +CONFIG_IPMI_PANIC_EVENT + When a panic occurs, this will cause the IPMI message handler to + generate an IPMI event describing the panic to each interface + registered with the message handler. + +Device interface for IPMI +CONFIG_IPMI_DEVICE_INTERFACE + This provides an IOCTL interface to the IPMI message handler so + userland processes may use IPMI. It supports poll() and select(). + +IPMI KCS handler +CONFIG_IPMI_KCS + Provides a driver for a KCS-style interface to a BMC. + +IPMI Watchdog Timer +CONFIG_IPMI_WATCHDOG + This enables the IPMI watchdog timer. + # # A couple of things I keep forgetting: # capitalize: AppleTalk, Ethernet, DOS, DMA, FAT, FTP, Internet, - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |