lkml.org 
[lkml]   [2003]   [Mar]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectRe: aic7(censored) dying horribly in 2.5.65-mm2 (fwd)
    Date
    Hi

    Similar issues here., though I must say the Adaptec driver hasn't worked for
    me on all kernels I tried since my first try with 2.5.44. I get almost the
    same output with a plain 2.5.65 kernel, though my kernel locks up just before
    the crash you get, I get no dmesg output.

    Note that it takes ages to get trough the SCSI driver towards the lockup. I
    guess some timeouts cause this.

    Config is the same, if it matters: SMP enabled.

    Bus 0, device 6, function 0:
    SCSI storage controller: Adaptec AIC-7880U (rev 0).

    Attached are a CD-RW and a tapedrive.

    2.4 kernels run fine.

    Please let me know if additional details are required.

    Jos

    > Friday 21 March 2003 08:17, Zwane Mwaikambo wrote:
    > Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
    > right at the end. Is there anything specific you want?
    >
    > 01:0d.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
    > 01:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
    >
    > There are 6 spindles on that second HBA, and a DLT and CDROM on the first.
    >
    > CONFIG_SCSI_AIC7XXX=y
    > CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
    > CONFIG_AIC7XXX_RESET_DELAY_MS=15000
    > # CONFIG_AIC7XXX_PROBE_EISA_VL is not set
    > # CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
    > CONFIG_AIC7XXX_DEBUG_ENABLE=y
    > CONFIG_AIC7XXX_DEBUG_MASK=0
    > CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
    > # CONFIG_SCSI_AIC7XXX_OLD is not set
    >
    > Starting NFS statd: [ OK ]
    > Loading keymap: scsi1:0:0:0: Attempting to queue an ABORT message
    >
    > >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
    >
    > scsi1: Dumping Card State while idle, at SEQADDR 0x8
    > Card was paused
    > ACCUM = 0x55, SINDEX = 0xa, DINDEX = 0x8c, ARG_2 = 0x0
    > HCNT = 0x0 SCBPTR = 0x8
    > SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) ERROR[0x40]:(PCIERRSTAT)
    > SCSIBUSL[0x80] LASTPHASE[0x1]:(P_BUSFREE)
    > SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
    > SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
    > SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
    > SSTAT0[0x25]:(DMADONE|SDONE|SELDI)
    > SSTAT1[0xb]:(REQINIT|PHASECHG|BUSFREE) SSTAT2[0x0]
    > SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
    > SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
    > DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
    > STACK: 0x0 0x169 0x10c 0x3
    > SCB count = 56
    > Kernel NEXTQSCB = 8
    > Card NEXTQSCB = 8
    > QINFIFO entries:
    > Waiting Queue entries:
    > Disconnected Queue entries: 0:13
    > QOUTFIFO entries:
    > Sequencer Free SCB List: 8 3 2 9 13 5 6 4 14 7 1 11 12 10 15
    > Sequencer SCB Info:
    > 0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xd]
    > 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > Pending list:
    > 13 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
    > Kernel Free SCB list: 10 11 0 25 41 28 31 40 45 29 30 46 47 24 26 5 20 21
    > 42 43 27 23 22 49 50 36 37 3 48 4 1 7 18 44 35
    > DevQ(0:0:0): 0 waiting
    > DevQ(0:1:0): 0 waiting
    > DevQ(0:2:0): 0 waiting
    > DevQ(0:3:0): 0 waiting
    > DevQ(0:4:0): 0 waiting
    > DevQ(0:5:0): 0 waiting
    >
    > <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
    > (scsi1:A:0:0): Device is disconnected, re-queuing SCB
    > Recovery code sleeping
    > (scsi1:A:0:0): Abort Tag Message Sent
    > (scsi1:A:0:0): SCB 13 - Abort Tag Completed.
    > Recovery SCB completes
    > Recovery code awake
    > aic7xxx_abort returns 0x2002
    > scsi1:0:0:0: Attempting to queue an ABORT message
    > scsi1:0:0:0: Command not found
    > aic7xxx_abort returns 0x2002
    > scsi1:0:0:0: Attempting to queue an ABORT message
    > scsi1:0:0:0: Command not found
    > aic7xxx_abort returns 0x2002
    > [ OK ]
    > Loading system font: scsi1:0:0:0: Attempting to queue an ABORT message
    > scsi1:0:0:0: Command not found
    > aic7xxx_abort returns 0x2002
    > scsi1:0:0:0: Attempting to queue an ABORT message
    > scsi1:0:0:0: Command not found
    > aic7xxx_abort returns 0x2002
    > scsi1:0:0:0: Attempting to queue an ABORT message
    > scsi1:0:0:0: Command not found
    > aic7xxx_abort returns 0x2002
    > scsi1:0:0:0: Attempting to queue a TARGET RESET message
    > scsi1:0:0:0: Command not found
    > aic7xxx_dev_reset returns 0x2002
    > scsi1:0:0:0: Attempting to queue an ABORT message
    > scsi1:0:0:0: Command not found
    > aic7xxx_abort returns 0x2002
    > scsi1:0:0:0: Attempting to queue an ABORT message
    >
    > >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
    >
    > scsi1: Dumping Card State while idle, at SEQADDR 0x8
    > Card was paused
    > ACCUM = 0xea, SINDEX = 0x64, DINDEX = 0x65, ARG_2 = 0xa
    > HCNT = 0x0 SCBPTR = 0x4
    > SCSISIGI[0x0] ERROR[0x40]:(PCIERRSTAT) SCSIBUSL[0x0]
    > LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
    > SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
    > SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x5]:(DMADONE|SDONE)
    > SSTAT1[0xa]:(PHASECHG|BUSFREE) SSTAT2[0x0] SSTAT3[0x0]
    > SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
    > SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
    > DFSTATUS[0x2d]:(FIFOEMP|DFTHRESH|HDONE|FIFOQWDEMP)
    > STACK: 0xe4 0x169 0x199 0x3
    > SCB count = 56
    > Kernel NEXTQSCB = 8
    > Card NEXTQSCB = 8
    > QINFIFO entries:
    > Waiting Queue entries:
    > Disconnected Queue entries: 4:43
    > QOUTFIFO entries:
    > Sequencer Free SCB List: 0 2 12 11 14 7 1 15 10 3 9 13 6 5 8
    > Sequencer SCB Info:
    > 0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 4 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0x2b]
    > 5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > 15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
    > SCB_LUN[0x0] SCB_TAG[0xff]
    > Pending list:
    > 43 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
    > Kernel Free SCB list: 31 44 46 30 40 45 29 3 24 23 37 47 20 21 5 42 27 26
    > 50 22 49 36 1 4 48 18 11 10 7 0 25 28 41 13 35
    > DevQ(0:0:0): 0 waiting
    > DevQ(0:1:0): 0 waiting
    > DevQ(0:2:0): 0 waiting
    > DevQ(0:3:0): 0 waiting
    > DevQ(0:4:0): 0 waiting
    > DevQ(0:5:0): 0 waiting
    >
    > <<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
    > (scsi1:A:0:0): Device is disconnected, re-queuing SCB
    > (scsi1:A:0:0): Recovery code sleeping
    > Abort Tag Message Sent
    > Recovery code awake
    > Timer Expired
    > aic7xxx_abort returns 0x2003
    > SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
    > end_request: I/O error, dev sda, sector 133984
    > Buffer I/O error on device sd(8,1), logical block 16744
    > SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
    > end_request: I/O error, dev sda, sector 4980800
    > Buffer I/O error on device sd(8,1), logical block 622596
    > Debug: sleeping function called from illegal context at
    > include/linux/rwsem.h:43
    > Call Trace:
    > [<c011ed18>] __might_sleep+0x58/0x60
    > [<c028ec00>] __bdevname+0x50/0xc0
    > [<c015cb41>] buffer_io_error+0x11/0x30
    > [<c015d406>] end_buffer_async_write+0x166/0x190
    > [<c0160101>] end_bio_bh_io_sync+0x21/0x30
    > [<c0161515>] bio_endio+0x35/0x60
    > [<c028df8f>] __end_that_request_first+0x1ff/0x220
    > [<c028dfc7>] end_that_request_first+0x17/0x20
    > [<c028a864>] elv_next_request+0x84/0xe0
    > [<c02e187f>] scsi_request_fn+0x3f/0x2a0
    > [<c028c442>] __blk_run_queue+0x12/0x20
    > [<c02e022d>] scsi_restart_operations+0xbd/0x120
    > [<c02e05b8>] scsi_error_handler+0x138/0x1a0
    > [<c02e0480>] scsi_error_handler+0x0/0x1a0
    > [<c0107095>] kernel_thread_helper+0x5/0x10
    > Buffer I/O error on device sd(8,1), logical block 557066
    > (scsi1:A:0:0): SCB 43 - Abort Tag Completed.
    > Recovery SCB completes
    >
    > Unable to handle kernel paging request at virtual address 6b6b6b6b
    > printing eip:
    > 6b6b6b6b
    > *pde = 00000000
    > Oops: 0000 [#1]
    > CPU: 1
    > EIP: 0060:[<6b6b6b6b>] Not tainted
    > EFLAGS: 00010002 VLI
    > EIP is at 0x6b6b6b6b
    > eax: cbb1ccf8 ebx: 00000000 ecx: cbe31290 edx: 00000000
    > esi: 00000001 edi: c1509f20 ebp: 00000005 esp: c1509ea0
    > ds: 007b es: 007b ss: 0068
    > Process swapper (pid: 0, threadinfo=c1508000 task=c150a660)
    > Stack: c02ff78c cbb1ccf8 cbb1ccf8 cbe31290 c0305c07 cbe31290 cbb1ccf8
    > 00000292 3e7ac717 c17e848c cbffe4f4 04000001 c010bb0d 00000005 cbe31290
    > c1509f20 c05060a0 c1508000 c1508000 00000005 c010be49 00000005 c1509f20
    > cbffe4f4 Call Trace:
    > [<c02ff78c>] ahc_linux_run_complete_queue+0x3c/0x50
    > [<c0305c07>] ahc_linux_isr+0x1d7/0x3a0
    > [<c010bb0d>] handle_IRQ_event+0x2d/0x50
    > [<c010be49>] do_IRQ+0x109/0x210
    > [<c010a398>] common_interrupt+0x18/0x20
    > [<c01264f6>] do_softirq+0x56/0xc0
    > [<c01168a5>] smp_apic_timer_interrupt+0xf5/0x160
    > [<c0106ea0>] default_idle+0x0/0x40
    > [<c010a41a>] apic_timer_interrupt+0x1a/0x20
    > [<c0106ea0>] default_idle+0x0/0x40
    > [<c0106ece>] default_idle+0x2e/0x40
    > [<c0106f5a>] cpu_idle+0x3a/0x50
    > [<c01226fd>] release_console_sem+0xbd/0x170
    > [<c012256b>] printk+0x1eb/0x270
    >
    > Code: Bad EIP value.
    > <0>Kernel panic: Aiee, killing interrupt handler!
    > In interrupt handler - not syncing
    >
    > -
    > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    > the body of a message to majordomo@vger.kernel.org
    > More majordomo info at http://vger.kernel.org/majordomo-info.html
    > Please read the FAQ at http://www.tux.org/lkml/

    -
    To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
    the body of a message to majordomo@vger.kernel.org
    More majordomo info at http://vger.kernel.org/majordomo-info.html
    Please read the FAQ at http://www.tux.org/lkml/

    \
     
     \ /
      Last update: 2005-03-22 13:34    [W:0.076 / U:149.488 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site