lkml.org 
[lkml]   [2003]   [Mar]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subjectaic7(censored) dying horribly in 2.5.65-mm2 (fwd)
Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops 
right at the end. Is there anything specific you want?

01:0d.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)
01:0e.0 SCSI storage controller: Adaptec AHA-294x / AIC-7870 (rev 03)

There are 6 spindles on that second HBA, and a DLT and CDROM on the first.

CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_PROBE_EISA_VL is not set
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
CONFIG_AIC7XXX_DEBUG_ENABLE=y
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
# CONFIG_SCSI_AIC7XXX_OLD is not set

Starting NFS statd: [ OK ]
Loading keymap: scsi1:0:0:0: Attempting to queue an ABORT message
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x8
Card was paused
ACCUM = 0x55, SINDEX = 0xa, DINDEX = 0x8c, ARG_2 = 0x0
HCNT = 0x0 SCBPTR = 0x8
SCSISIGI[0xe6]:(REQI|BSYI|MSGI|IOI|CDI) ERROR[0x40]:(PCIERRSTAT)
SCSIBUSL[0x80] LASTPHASE[0x1]:(P_BUSFREE)
SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
SSTAT0[0x25]:(DMADONE|SDONE|SELDI)
SSTAT1[0xb]:(REQINIT|PHASECHG|BUSFREE) SSTAT2[0x0]
SSTAT3[0x0] SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
DFSTATUS[0x29]:(FIFOEMP|HDONE|FIFOQWDEMP)
STACK: 0x0 0x169 0x10c 0x3
SCB count = 56
Kernel NEXTQSCB = 8
Card NEXTQSCB = 8
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 0:13
QOUTFIFO entries:
Sequencer Free SCB List: 8 3 2 9 13 5 6 4 14 7 1 11 12 10 15
Sequencer SCB Info:
0 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xd]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
Pending list:
13 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 10 11 0 25 41 28 31 40 45 29 30 46 47 24 26 5 20 21
42 43 27 23 22 49 50 36 37 3 48 4 1 7 18 44 35
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
DevQ(0:3:0): 0 waiting
DevQ(0:4:0): 0 waiting
DevQ(0:5:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi1:A:0:0): Device is disconnected, re-queuing SCB
Recovery code sleeping
(scsi1:A:0:0): Abort Tag Message Sent
(scsi1:A:0:0): SCB 13 - Abort Tag Completed.
Recovery SCB completes
Recovery code awake
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
[ OK ]
Loading system font: scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue a TARGET RESET message
scsi1:0:0:0: Command not found
aic7xxx_dev_reset returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
scsi1:0:0:0: Command not found
aic7xxx_abort returns 0x2002
scsi1:0:0:0: Attempting to queue an ABORT message
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State while idle, at SEQADDR 0x8
Card was paused
ACCUM = 0xea, SINDEX = 0x64, DINDEX = 0x65, ARG_2 = 0xa
HCNT = 0x0 SCBPTR = 0x4
SCSISIGI[0x0] ERROR[0x40]:(PCIERRSTAT) SCSIBUSL[0x0]
LASTPHASE[0x1]:(P_BUSFREE) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI)
SBLKCTL[0x2]:(SELWIDE) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE)
SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED) SSTAT0[0x5]:(DMADONE|SDONE)
SSTAT1[0xa]:(PHASECHG|BUSFREE) SSTAT2[0x0] SSTAT3[0x0]
SIMODE0[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO)
SXFRCTL0[0x80]:(DFON) DFCNTRL[0x0]
DFSTATUS[0x2d]:(FIFOEMP|DFTHRESH|HDONE|FIFOQWDEMP)
STACK: 0xe4 0x169 0x199 0x3
SCB count = 56
Kernel NEXTQSCB = 8
Card NEXTQSCB = 8
QINFIFO entries:
Waiting Queue entries:
Disconnected Queue entries: 4:43
QOUTFIFO entries:
Sequencer Free SCB List: 0 2 12 11 14 7 1 15 10 3 9 13 6 5 8
Sequencer SCB Info:
0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
1 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
4 SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0x2b]
5 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
6 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
7 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
8 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
9 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
10 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
11 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
12 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
13 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
14 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
15 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0x7]
SCB_LUN[0x0] SCB_TAG[0xff]
Pending list:
43 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0x7] SCB_LUN[0x0]
Kernel Free SCB list: 31 44 46 30 40 45 29 3 24 23 37 47 20 21 5 42 27 26
50 22 49 36 1 4 48 18 11 10 7 0 25 28 41 13 35
DevQ(0:0:0): 0 waiting
DevQ(0:1:0): 0 waiting
DevQ(0:2:0): 0 waiting
DevQ(0:3:0): 0 waiting
DevQ(0:4:0): 0 waiting
DevQ(0:5:0): 0 waiting
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi1:A:0:0): Device is disconnected, re-queuing SCB
(scsi1:A:0:0): Recovery code sleeping
Abort Tag Message Sent
Recovery code awake
Timer Expired
aic7xxx_abort returns 0x2003
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
end_request: I/O error, dev sda, sector 133984
Buffer I/O error on device sd(8,1), logical block 16744
SCSI disk error : host 1 channel 0 id 0 lun 0 return code = 6000000
end_request: I/O error, dev sda, sector 4980800
Buffer I/O error on device sd(8,1), logical block 622596
Debug: sleeping function called from illegal context at
include/linux/rwsem.h:43
Call Trace:
[<c011ed18>] __might_sleep+0x58/0x60
[<c028ec00>] __bdevname+0x50/0xc0
[<c015cb41>] buffer_io_error+0x11/0x30
[<c015d406>] end_buffer_async_write+0x166/0x190
[<c0160101>] end_bio_bh_io_sync+0x21/0x30
[<c0161515>] bio_endio+0x35/0x60
[<c028df8f>] __end_that_request_first+0x1ff/0x220
[<c028dfc7>] end_that_request_first+0x17/0x20
[<c028a864>] elv_next_request+0x84/0xe0
[<c02e187f>] scsi_request_fn+0x3f/0x2a0
[<c028c442>] __blk_run_queue+0x12/0x20
[<c02e022d>] scsi_restart_operations+0xbd/0x120
[<c02e05b8>] scsi_error_handler+0x138/0x1a0
[<c02e0480>] scsi_error_handler+0x0/0x1a0
[<c0107095>] kernel_thread_helper+0x5/0x10
Buffer I/O error on device sd(8,1), logical block 557066
(scsi1:A:0:0): SCB 43 - Abort Tag Completed.
Recovery SCB completes
Unable to handle kernel paging request at virtual address 6b6b6b6b
printing eip:
6b6b6b6b
*pde = 00000000
Oops: 0000 [#1]
CPU: 1
EIP: 0060:[<6b6b6b6b>] Not tainted
EFLAGS: 00010002 VLI
EIP is at 0x6b6b6b6b
eax: cbb1ccf8 ebx: 00000000 ecx: cbe31290 edx: 00000000
esi: 00000001 edi: c1509f20 ebp: 00000005 esp: c1509ea0
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1508000 task=c150a660)
Stack: c02ff78c cbb1ccf8 cbb1ccf8 cbe31290 c0305c07 cbe31290 cbb1ccf8 00000292
3e7ac717 c17e848c cbffe4f4 04000001 c010bb0d 00000005 cbe31290 c1509f20
c05060a0 c1508000 c1508000 00000005 c010be49 00000005 c1509f20 cbffe4f4
Call Trace:
[<c02ff78c>] ahc_linux_run_complete_queue+0x3c/0x50
[<c0305c07>] ahc_linux_isr+0x1d7/0x3a0
[<c010bb0d>] handle_IRQ_event+0x2d/0x50
[<c010be49>] do_IRQ+0x109/0x210
[<c010a398>] common_interrupt+0x18/0x20
[<c01264f6>] do_softirq+0x56/0xc0
[<c01168a5>] smp_apic_timer_interrupt+0xf5/0x160
[<c0106ea0>] default_idle+0x0/0x40
[<c010a41a>] apic_timer_interrupt+0x1a/0x20
[<c0106ea0>] default_idle+0x0/0x40
[<c0106ece>] default_idle+0x2e/0x40
[<c0106f5a>] cpu_idle+0x3a/0x50
[<c01226fd>] release_console_sem+0xbd/0x170
[<c012256b>] printk+0x1eb/0x270
Code: Bad EIP value.
<0>Kernel panic: Aiee, killing interrupt handler!
In interrupt handler - not syncing

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:34    [from the cache]
©2003-2014 Jasper Spaans. Advertise on this site