Messages in this thread |  | | Date | Thu, 13 Mar 2003 16:58:29 +0100 | From | Jurriaan <> | Subject | 2.5.64 tdfxfb problems: 'fb: can't remap 3Dfx VooDoo 5 register area' |
| |
When I try to use the tdfxfb framebuffer module with the 2.5.64 kernel, I get the following message:
fb: Can't remap 3Dfx Voodoo5 register area.
Is there any way to solve this? I tried google, but I can't find any solution for this :-(
If I compile the tdfxfb framebuffer into the kernel, I get an oops during booting with the backlog below. That is rather less nice, but even as a module it won't work.
Thanks for your attention, Jurriaan
remap_area_pages get_vm_Area __ioremap rioremap_nocache sysfs_mkdir pci_device_probe bus_match driver_attach bus_add_driver driver_register proc_register pci_register_driver init init kernel_thread_helper
Linux middle 2.5.64 #1 Thu Mar 13 16:43:09 CET 2003 i686 unknown unknown GNU/Linux Gnu C 3.2.3 Gnu make 3.80 util-linux 2.11y mount 2.11y module-init-tools 0.9.10 e2fsprogs 1.32 PPP 2.4.1 Linux C Library 2.3.1 Dynamic linker (ldd) 2.3.1 Procps 3.1.6 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 4.5.9 Modules Loaded tdfxfb cfbimgblt
00:00.0 Host bridge: nVidia Corporation: Unknown device 01e0 (rev a2) Subsystem: Asustek Computer, Inc.: Unknown device 80ac Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M] Capabilities: [40] AGP version 2.0 Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x1 Capabilities: [60] #08 [2001]
00:00.1 RAM memory: nVidia Corporation: Unknown device 01eb (rev a2) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.2 RAM memory: nVidia Corporation: Unknown device 01ee (rev a2) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation: Unknown device 01ed (rev a2) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.4 RAM memory: nVidia Corporation: Unknown device 01ec (rev a2) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.5 RAM memory: nVidia Corporation: Unknown device 01ef (rev a2) Subsystem: nVidia Corporation: Unknown device 0c17 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a3) Subsystem: Asustek Computer, Inc. A7N8X Mainboard Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [48] #08 [01e1]
00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2) Subsystem: Asustek Computer, Inc.: Unknown device 0c11 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 0 Region 0: I/O ports at e400 [size=32] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3) (prog-if 10 [OHCI]) Subsystem: Asustek Computer, Inc. A7N8X Mainboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at ec004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3) (prog-if 10 [OHCI]) Subsystem: Asustek Computer, Inc. A7N8X Mainboard Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 5 Region 0: Memory at ec005000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a3) (prog-if 20 [EHCI]) Subsystem: Asustek Computer, Inc. A7N8X Mainboard Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 11 Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] #0a [2080] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1) Subsystem: Asustek Computer, Inc.: Unknown device 80a7 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at ec001000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at d000 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1) Subsystem: Asustek Computer, Inc.: Unknown device 8095 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at d400 [size=256] Region 1: I/O ports at d800 [size=128] Region 2: Memory at ec002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 PCI bridge: nVidia Corporation: Unknown device 006c (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000a000-0000cfff Memory behind bridge: d0000000-dfffffff Prefetchable memory behind bridge: e0000000-e7ffffff BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if 8a [Master SecP PriP]) Subsystem: Asustek Computer, Inc.: Unknown device 0c11 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Region 4: I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
01:06.0 VGA compatible controller: 3Dfx Interactive, Inc. Voodoo 4 / Voodoo 5 (rev 01) (prog-if 00 [VGA]) Subsystem: 3Dfx Interactive, Inc.: Unknown device 0005 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ Interrupt: pin A routed to IRQ 5 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=128M] Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M] Region 2: I/O ports at a000 [size=256] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:07.0 SCSI storage controller: LSI Logic / Symbios Logic 53c860 (rev 13) Subsystem: LSI Logic / Symbios Logic: Unknown device 1000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2000ns min, 16000ns max), cache line size 08 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at a400 [size=256] Region 1: Memory at d9021000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:08.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20) Subsystem: Lite-On Communications Inc LNE100TX Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at a800 [size=256] Region 1: Memory at d9020000 (32-bit, non-prefetchable) [size=256] Expansion ROM at <unassigned> [disabled] [size=256K]
01:09.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) Subsystem: Creative Labs SBLive! Player 5.1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min, 5000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at ac00 [size=32] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:09.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07) Subsystem: Creative Labs Gameport Joystick Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Region 0: I/O ports at b000 [size=8] Capabilities: [dc] Power Management version 1 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:0a.0 Unknown mass storage controller: Promise Technology, Inc. 20265 (rev 02) Subsystem: Promise Technology, Inc. Ultra100 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at b400 [size=8] Region 1: I/O ports at b800 [size=4] Region 2: I/O ports at bc00 [size=8] Region 3: I/O ports at c000 [size=4] Region 4: I/O ports at c400 [size=64] Region 5: Memory at d9000000 (32-bit, non-prefetchable) [size=128K] Expansion ROM at <unassigned> [disabled] [size=64K] Capabilities: [58] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000-001f : dma1 0020-003f : pic1 0040-005f : timer 0060-006f : keyboard 0070-007f : rtc 0080-008f : dma page reg 00a0-00bf : pic2 00c0-00df : dma2 00f0-00ff : fpu 0170-0177 : ide1 01f0-01f7 : ide0 02f8-02ff : serial 0376-0376 : ide1 0378-037a : parport0 03c0-03df : vga+ 03f6-03f6 : ide0 03f8-03ff : serial 0cf8-0cff : PCI conf1 a000-cfff : PCI Bus #01 a000-a0ff : 3Dfx Interactive, In Voodoo 4 / Voodoo 5 a400-a4ff : LSI Logic / Symbios 53c860 a400-a47f : sym53c8xx a800-a8ff : Lite-On Communicatio LNE100TX a800-a8ff : tulip ac00-ac1f : Creative Labs SB Live! EMU10k1 ac00-ac1f : EMU10K1 b000-b007 : Creative Labs SB Live! MIDI/Game P b400-b407 : Promise Technology, 20265 b400-b407 : ide2 b800-b803 : Promise Technology, 20265 b802-b802 : ide2 bc00-bc07 : Promise Technology, 20265 bc00-bc07 : ide3 c000-c003 : Promise Technology, 20265 c002-c002 : ide3 c400-c43f : Promise Technology, 20265 c400-c407 : ide2 c408-c40f : ide3 c410-c43f : PDC20265 d000-d007 : PCI device 10de:0066 (nVidia Corporation) d400-d4ff : PCI device 10de:006a (nVidia Corporation) d800-d87f : PCI device 10de:006a (nVidia Corporation) d800-d83f : NVidia NForce2 - Controller e400-e41f : PCI device 10de:0064 (nVidia Corporation) f000-f00f : PCI device 10de:0065 (nVidia Corporation) f000-f007 : ide0 f008-f00f : ide1
00000000-0009fbff : System RAM 0009fc00-0009ffff : reserved 000a0000-000bffff : Video RAM area 000c0000-000c7fff : Video ROM 000c8000-000c97ff : Extension ROM 000f0000-000fffff : System ROM 00100000-3ffeffff : System RAM 00100000-00372c59 : Kernel code 00372c5a-00440ac3 : Kernel data 3fff0000-3fff2fff : ACPI Non-volatile Storage 3fff3000-3fffffff : ACPI Tables d0000000-dfffffff : PCI Bus #01 d0000000-d7ffffff : 3Dfx Interactive, In Voodoo 4 / Voodoo 5 d9000000-d901ffff : Promise Technology, 20265 d9020000-d90200ff : Lite-On Communicatio LNE100TX d9020000-d90200ff : tulip d9021000-d90210ff : LSI Logic / Symbios 53c860 e0000000-e7ffffff : PCI Bus #01 e0000000-e7ffffff : 3Dfx Interactive, In Voodoo 4 / Voodoo 5 e8000000-ebffffff : PCI device 10de:01e0 (nVidia Corporation) ec000000-ec0000ff : PCI device 10de:0068 (nVidia Corporation) ec001000-ec001fff : PCI device 10de:0066 (nVidia Corporation) ec002000-ec002fff : PCI device 10de:006a (nVidia Corporation) ec002000-ec0021ff : NVidia NForce2 - AC'97 ec004000-ec004fff : PCI device 10de:0067 (nVidia Corporation) ec005000-ec005fff : PCI device 10de:0067 (nVidia Corporation) fec00000-fec00fff : reserved fee00000-fee00fff : reserved ffff0000-ffffffff : reserved
Linux version 2.5.64 (root@middle) (gcc version 3.2.3 20030309 (Debian prerelease)) #1 Thu Mar 13 16:43:09 CET 2003 Video mode to be used for restore is f00 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. On node 0 totalpages: 229376 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 225280 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 Building zonelist for node : 0 Kernel command line: root=/dev/hda1 hdb=scsi apm=power-off ide_setup: hdb=scsi Initializing CPU#0 PID hash table entries: 4096 (order 12: 32768 bytes) Detected 1996.046 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3948.54 BogoMIPS Memory: 903596k/917504k available (2507k kernel code, 13124k reserved, 823k data, 380k init, 0k highmem) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 131072 (order: 7, 524288 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Failed to register 'sysfs' in sysfs -> /dev -> /dev/console -> /root CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Machine check exception polling timer started. CPU: AMD Athlon(tm) XP 2400+ stepping 01 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket mtrr: v2.0 (20020519) PCI: PCI BIOS revision 2.10 entry at 0xfb4c0, last bus=2 PCI: Using configuration type 1 BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec pool[0]: 1 bvecs: 256 entries (12 bytes) biovec pool[1]: 4 bvecs: 256 entries (48 bytes) biovec pool[2]: 16 bvecs: 256 entries (192 bytes) biovec pool[3]: 64 bvecs: 256 entries (768 bytes) biovec pool[4]: 128 bvecs: 256 entries (1536 bytes) biovec pool[5]: 256 bvecs: 256 entries (3072 bytes) block request queues: 128 requests per read queue 128 requests per write queue 8 requests per batch enter congestion at 15 exit congestion at 17 SCSI subsystem initialized drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Discovered primary peer bus ff [IRQ] PCI: Using IRQ router default [10de/01e0] at 00:00.0 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) Enabling SEP on CPU 0 aio_setup: sizeof(struct page) = 40 Journalled Block Device driver loaded NTFS driver 2.1.0 [Flags: R/O]. udf: registering filesystem Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] parport0: irq 7 detected parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) pty: 256 Unix98 ptys configured lp0: using parport0 (polling). Real Time Clock Driver v1.11 Software Watchdog Timer: 0.06, soft_margin: 60 sec, nowayout: 0 Linux agpgart interface v0.100 (c) Dave Jones [drm:drm_init] *ERROR* Cannot initialize the agpgart module. Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) Linux Tulip driver version 1.1.13 (May 11, 2002) tulip0: MII transceiver #1 config 3100 status 7829 advertising 01e1. eth0: Lite-On 82c168 PNIC rev 32 at 0xf8800000, 00:A0:CC:21:A1:AC, IRQ 5. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE2: IDE controller at PCI slot 00:09.0 NFORCE2: chipset revision 162 NFORCE2: not 100% native mode: will probe irqs later AMD_IDE: PCI device 10de:0065 (nVidia Corporation) (rev a2) UDMA100 controller on pci00:09.0 ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA hda: IBM-DTLA-307045, ATA DISK drive hdb: LITE-ON LTR-40125W, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: Maxtor 4G120J6, ATA DISK drive hdd: Maxtor 4G120J6, ATA DISK drive ide1 at 0x170-0x177,0x376 on irq 15 PDC20265: IDE controller at PCI slot 01:0a.0 PDC20265: chipset revision 2 PDC20265: not 100% native mode: will probe irqs later PDC20265: (U)DMA Burst Bit DISABLED Primary PCI Mode Secondary PCI Mode. ide2: BM-DMA at 0xc400-0xc407, BIOS settings: hde:DMA, hdf:pio ide3: BM-DMA at 0xc408-0xc40f, BIOS settings: hdg:DMA, hdh:pio hde: WDC WD800JB-00CRA1, ATA DISK drive ide2 at 0xb400-0xb407,0xb802 on irq 5 hdg: WDC WD800JB-00CRA1, ATA DISK drive ide3 at 0xbc00-0xbc07,0xc002 on irq 5 hda: host protected area => 1 hda: 90069840 sectors (46116 MB) w/1916KiB Cache, CHS=89355/16/63, UDMA(100) hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 > hdc: host protected area => 1 hdc: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(33) hdc: hdc1 hdc2 hdd: host protected area => 1 hdd: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=14946/255/63, UDMA(33) hdd: hdd1 hdd2 hde: host protected area => 1 hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100) hde: hde1 hde2 hdg: host protected area => 1 hdg: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(100) hdg: hdg1 hdg2 ide-cd: passing drive hdb to ide-scsi emulation. scsi HBA driver sym53c8xx didn't set a release method, please fix the template sym.1.7.0: setting PCI_COMMAND_PARITY... sym.1.7.0: setting PCI_COMMAND_INVALIDATE. sym0: <860> rev 0x13 on pci bus 1 device 7 function 0 irq 11 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.1.16a Vendor: TOSHIBA Model: DVD-ROM SD-M1401 Rev: 1007 Type: CD-ROM ANSI SCSI revision: 02 Vendor: PLEXTOR Model: CD-ROM PX-32TS Rev: 1.02 Type: CD-ROM ANSI SCSI revision: 02 Vendor: YAMAHA Model: CRW2100S Rev: 1.0N Type: CD-ROM ANSI SCSI revision: 02 scsi1 : SCSI host adapter emulation for IDE ATAPI devices Vendor: LITE-ON Model: LTR-40125W Rev: WS05 Type: CD-ROM ANSI SCSI revision: 02 st: Version 20021214, fixed bufsize 32768, wrt 30720, s/g segs 256 sym0:1: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8) sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0 sym0:2: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 8) sr1: scsi-1 drive Attached scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0 sym0:5: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 7) sr2: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr2 at scsi0, channel 0, id 5, lun 0 sr3: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr3 at scsi1, channel 0, id 0, lun 0 drivers/usb/core/usb.c: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver drivers/usb/core/usb.c: registered new driver usbscanner drivers/usb/image/scanner.c: 0.4.11:USB Scanner Driver mice: PS/2 mouse device common for all mice input: PC Speaker input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 i2c-dev.o: i2c /dev entries driver module version 2.7.0 (20021208) i2c-proc.o version 2.7.0 (20021208) md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 2832.000 MB/sec 8regs_prefetch: 2740.000 MB/sec 32regs : 1948.000 MB/sec 32regs_prefetch: 1744.000 MB/sec pIII_sse : 5312.000 MB/sec pII_mmx : 4584.000 MB/sec p5_mmx : 5836.000 MB/sec raid5: using function: pIII_sse (5312.000 MB/sec) md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 Advanced Linux Sound Architecture Driver Version 0.9.0rc7 (Sat Feb 15 15:01:21 2003 UTC). request_module: failed /sbin/modprobe -- snd-card-0. error = -16 PCI: Setting latency timer of device 00:06.0 to 64 intel8x0: clocking to 47447 ALSA device list: #0: NVidia NForce2 at 0xec002000, irq 5 #1: Sound Blaster Live! (rev.7) at 0xac00, irq 11 NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. md: Autodetecting RAID arrays. md: autorun ... md: considering hdg2 ... md: adding hdg2 ... md: hdg1 has different UUID to hdg2 md: adding hde2 ... md: hde1 has different UUID to hdg2 md: created md1 md: bind<hde2> md: bind<hdg2> md: running: <hdg2><hde2> md1: max total readahead window set to 512k md1: 2 data-disks, max readahead per data-disk: 256k md1: setting max_sectors to 128, segment boundary to 32767 raid0: looking at hdg2 raid0: comparing hdg2(17670656) with hdg2(17670656) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at hde2 raid0: comparing hde2(17670656) with hdg2(17670656) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 35341312 blocks. raid0 : conf->smallest->size is 35341312 blocks. raid0 : nb_zone is 1. raid0 : Allocating 8 bytes for hash. md: marking sb clean... md: marking sb clean... md: updating md1 RAID superblock on device (in sync 1) md: hdg2 <6>(write) hdg2's sb offset: 17670656 md: hde2 <6>(write) hde2's sb offset: 17670656 md: considering hdg1 ... md: adding hdg1 ... md: adding hde1 ... md: created md0 md: bind<hde1> md: bind<hdg1> md: running: <hdg1><hde1> md0: max total readahead window set to 512k md0: 2 data-disks, max readahead per data-disk: 256k md0: setting max_sectors to 128, segment boundary to 32767 raid0: looking at hdg1 raid0: comparing hdg1(60479872) with hdg1(60479872) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at hde1 raid0: comparing hde1(60479872) with hdg1(60479872) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 120959744 blocks. raid0 : conf->smallest->size is 120959744 blocks. raid0 : nb_zone is 1. raid0 : Allocating 8 bytes for hash. md: marking sb clean... md: marking sb clean... md: updating md0 RAID superblock on device (in sync 1) md: hdg1 <6>(write) hdg1's sb offset: 60479872 md: hde1 <6>(write) hde1's sb offset: 60479872 md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 380k freed Adding 2000368k swap on /dev/hda3. Priority:-1 extents:1 EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,1), internal journal kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,8), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,8)) for (ide0(3,8)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,6), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,6)) for (ide0(3,6)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,5), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,5)) for (ide0(3,5)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide0(3,10), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide0(3,10)) for (ide0(3,10)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device md(9,0), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (md(9,0)) for (md(9,0)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device md(9,1), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (md(9,1)) for (md(9,1)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,1), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,1)) for (ide1(22,1)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,2), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,2)) for (ide1(22,2)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,65), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,65)) for (ide1(22,65)) Using r5 hash to sort names found reiserfs format "3.6" with standard journal Reiserfs journal params: device ide1(22,66), size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 reiserfs: checking transaction log (ide1(22,66)) for (ide1(22,66)) Using r5 hash to sort names eth0: Setting full-duplex based on MII#1 link partner capability of 05e1. fb: Can't remap 3Dfx Voodoo5 register area. -- The mark of a true M.B.A. is that he is often wrong but seldom in doubt. GNU/Linux 2.5.64 SMP/ReiserFS 3948 bogomips load av: 0.65 0.29 0.12 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
|  |