lkml.org 
[lkml]   [2003]   [Feb]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Promise FastTrak TX4 losing interrupts (with apic mode)
Try to boot with apic=no or acpi=oldboot


however this both options work for me.
I have supermicro 370dl3 dual PIII 1Ghz, and TX2 card.


Cheer,
+AU

On Thu, 6 Feb 2003, Stephan van Hienen wrote:

> replying on an old thread
> looks like i have the same problem as below
>
> kernel 2.4.20 intel sc7500cw mainbord (dual xeon)
> booting with noapic appended resolves the lost interrupt messages
> (only happens on the TX4 disks (there is also an onboard
> FastTrak100(2channel)which works ok)
>
> I don't use the promise raid code, just using the card to use some extra
> ide channels for my sw raid5
>
> i get exactly the same error when booting :
>
> hde: lost interrupt
> hde: lost interrupt
> ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> hde: lost interrupt
> unknown partition table
> hdg: lost interrupt
> hdg: lost interrupt
> ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> hdg: lost interrupt
> unknown partition table
> hdi: lost interrupt
> hdi: lost interrupt
> ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> hdi: lost interrupt
> unknown partition table
>
> moved arround the tx4 card between pci slots (and busses (mainbord has 3
> pci busses)) but keeps getting the same error
> the tx4 always gets irq48 (not shared with anything else)
>
> only booting with noapic fixes it
> (are there any negative point when running in 'noapic mode' ?(besides
> losing high irq's))
>
>
> On Wed, 31 Oct 2001, Hans-Peter Jansen wrote:
>
> > On Wednesday, 31. October 2001 15:14, Shawn Evans wrote:
> > > Hans,
> > >
> > > I have a TX4 and have been unsuccessful in getting it to work 100%... The
> > > second card losses interrupts... The board... if you don't already have
> > > one... seems as if it is just 2 TX2 on one board... ( turning off the slave
> > > ). The chips say 20270... but everything that sees then says 20268...
> > > here is some info.. maybe it will help you and maybe you can help me.
> > > Running 2.4.12 with patches from redhat ata-raid site. (also I have an hpt
> > > on board which you can see.. but no drives are hooked up)
> > >
> > > I have been thinking.. that if Linux software raid is better than the
> > > drivers in the kernel... it might be possible to set up a TX4 to control 8
> > > drives... :-)
> >
> > Looks like you mean the ataraid stuff here. I'm trying to avoid that.
> > Haven't tried to slave some drives on the TX4 either, but to my experience,
> > a slaved drive on PDC20268 sucks performance wise...
> >
> > >
> > > dmesg:
> > >
> > > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> > > VP_IDE: IDE controller on PCI bus 00 dev 39
> > > VP_IDE: chipset revision 6
> > > VP_IDE: not 100% native mode: will probe irqs later
> > > VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
> > > ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:pio
> > > ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:DMA, hdd:pio
> > > HPT370A: IDE controller on PCI bus 00 dev 70
> > > HPT370A: chipset revision 4
> > > HPT370A: not 100% native mode: will probe irqs later
> > > ide2: BM-DMA at 0xec00-0xec07, BIOS settings: hde:pio, hdf:pio
> > > ide3: BM-DMA at 0xec08-0xec0f, BIOS settings: hdg:pio, hdh:pio
> > > PDC20268: IDE controller on PCI bus 03 dev 08
> > > PDC20268: chipset revision 2
> > > PDC20268: not 100% native mode: will probe irqs later
> > > PDC20268: pci-config space interrupt mirror fixed.
> > > PDC20268: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
> > > Mode.
> > > ide4: BM-DMA at 0xa000-0xa007, BIOS settings: hdi:pio, hdj:pio
> > > ide5: BM-DMA at 0xa008-0xa00f, BIOS settings: hdk:pio, hdl:pio
> > > PDC20268: IDE controller on PCI bus 03 dev 10
> > > PDC20268: chipset revision 2
> > > PDC20268: not 100% native mode: will probe irqs later
> > > PDC20268: ROM enabled at 0x000dc000
> > > PDC20268: pci-config space interrupt mirror fixed.
> > > PDC20268: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER
> > > Mode.
> > > ide6: BM-DMA at 0xb400-0xb407, BIOS settings: hdm:pio, hdn:pio
> > > ide7: BM-DMA at 0xb408-0xb40f, BIOS settings: hdo:pio, hdp:pio
> > > hda: WDC WD800BB-00BSA0, ATA DISK drive
> > > hdc: YAMAHA CRW2100E, ATAPI CD/DVD-ROM drive
> > > hdi: WDC WD800BB-00BSA0, ATA DISK drive
> > > hdk: WDC WD800BB-00BSA0, ATA DISK drive
> > > hdm: WDC WD800BB-00BSA0, ATA DISK drive
> > > hdo: WDC WD800BB-00BSA0, ATA DISK drive
> > > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > > ide1 at 0x170-0x177,0x376 on irq 15
> > > ide4 at 0x9000-0x9007,0x9402 on irq 11
> > > ide5 at 0x9800-0x9807,0x9c02 on irq 11
> > > ide6 at 0xa400-0xa407,0xa802 on irq 10
> > > ide7 at 0xac00-0xac07,0xb002 on irq 10
> > > hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63,
> > > UDMA(100)
> > > hdi: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63,
> > > UDMA(66)
> > > hdk: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63,
> > > UDMA(66)
> > > hdm: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63,
> > > UDMA(66)
> > > hdo: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63,
> > > UDMA(66)
> > > Partition check:
> > > hda: hda1 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 >
> > > hdi: [PTBL] [9729/255/63] hdi1
> > > hdk: unknown partition table
> > > hdm:hdm: lost interrupt
> > > hdm: lost interrupt
> > > hdm: lost interrupt
> > > ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> > > hdm: lost interrupt
> > > unknown partition table
> > > hdo:hdo: lost interrupt
> > > hdo: lost interrupt
> > > hdo: lost interrupt
> > > ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> > > hdo: lost interrupt
> > > unknown partition table
> > > loop: loaded (max 8 devices)
> > > Linux agpgart interface v0.99 (c) Jeff Hartmann
> > > agpgart: Maximum main memory to use for agp memory: 816M
> > > agpgart: Detected Via Apollo Pro chipset
> > > agpgart: AGP aperture is 64M @ 0xd0000000
> > > ide_dmaproc: chipset supported ide_dma_lostirq func only: 13
> > > hdm: lost interrupt
> > > ataraid/d0: ataraid/d0p1
> > > Drive 0 is 76319 Mb (56 / 0)
> > > Drive 1 is 76319 Mb (57 / 0)
> > > Drive 2 is 76319 Mb (88 / 0)
> > > Raid0 array consists of 3 drives.
> > > Promise Fasttrak(tm) Softwareraid driver for linux version 0.03beta
> > > Highpoint HPT370 Softwareraid driver for linux version 0.01
> > > No raid array found
> > >
> >
> > Your problem is different to mine. BTW, Andre made a new patch at
> > http://www.linuxdiskcert.org. It drives the TX4 in UDMA(100) mode
> > at least.
> >
> > > cat /proc/io:
> > > iomem ioports
> > > [root@god root]# cat /proc/ioports
> > > 0000-001f : dma1
> > > 0020-003f : pic1
> > > 0040-005f : timer
> > > 0060-006f : keyboard
> > > 0080-008f : dma page reg
> > > 00a0-00bf : pic2
> > > 00c0-00df : dma2
> > > 00f0-00ff : fpu
> > > 0170-0177 : ide1
> > > 01f0-01f7 : ide0
> > > 02f8-02ff : serial(auto)
> > > 0376-0376 : ide1
> > > 0378-037a : parport0
> > > 03c0-03df : vga+
> > > 03f6-03f6 : ide0
> > > 03f8-03ff : serial(auto)
> > > 0cf8-0cff : PCI conf1
> > > 5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> > > 6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
> > > 9000-bfff : PCI Bus #03
> > > 9000-9007 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > 9000-9007 : ide4
> > > 9400-9403 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > 9402-9402 : ide4
> > > 9800-9807 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > 9800-9807 : ide5
> > > 9c00-9c03 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > 9c02-9c02 : ide5
> > > a000-a00f : PCI device 105a:6268 (Promise Technology, Inc.)
> > > a000-a007 : ide4
> > > a008-a00f : ide5
> > > a010-a01f : PDC20268
> > > a400-a407 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > a400-a407 : ide6
> > > a800-a803 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > a802-a802 : ide6
> > > ac00-ac07 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > ac00-ac07 : ide7
> > > b000-b003 : PCI device 105a:6268 (Promise Technology, Inc.)
> > > b002-b002 : ide7
> > > b400-b40f : PCI device 105a:6268 (Promise Technology, Inc.)
> > > b400-b407 : ide6
> > > b408-b40f : ide7
> > > b410-b41f : PDC20268
> > > c000-cfff : PCI Bus #02
> > > c000-c07f : 3Com Corporation 3c980-TX 10/100baseTX NIC [Python-T]
> > > c000-c07f : 02:04.0
> > > c400-c47f : 3Com Corporation 3c980-TX 10/100baseTX NIC [Python-T] (#2)
> > > c400-c47f : 02:05.0
> > > d000-d01f : VIA Technologies, Inc. UHCI USB (#2)
> > > d400-d40f : VIA Technologies, Inc. Bus Master IDE
> > > d400-d407 : ide0
> > > d408-d40f : ide1
> > > d800-d81f : VIA Technologies, Inc. UHCI USB
> > > dc00-dc07 : Triones Technologies, Inc. HPT366 / HPT370
> > > e000-e003 : Triones Technologies, Inc. HPT366 / HPT370
> > > e400-e407 : Triones Technologies, Inc. HPT366 / HPT370
> > > e800-e803 : Triones Technologies, Inc. HPT366 / HPT370
> > > ec00-ecff : Triones Technologies, Inc. HPT366 / HPT370
> > > ec00-ec07 : ide2
> > > ec08-ec0f : ide3
> > > ec10-ecff : HPT370A
> > >
> > >
> > > cat /proc/interrupts
> > > CPU0 CPU1
> > > 0: 4088270 4605986 IO-APIC-edge timer
> > > 1: 208 203 IO-APIC-edge keyboard
> > > 2: 0 0 XT-PIC cascade
> > > 9: 21438 21722 IO-APIC-level eth0
> > > 10: 0 0 IO-APIC-level ide6, ide7, eth1
> > > 11: 5093433 5093439 IO-APIC-level ide4, ide5
> > > 12: 26352 29204 IO-APIC-edge PS/2 Mouse
> > > 14: 75567 56241 IO-APIC-edge ide0
> > > 15: 187 99 IO-APIC-edge ide1
> > > NMI: 0 0
> > > LOC: 8694029 8694028
> > > ERR: 0
> > > MIS: 0
> > >
> >
> > Disabling eth1 may help you. What mobo you're using?
> >
> > > for i in hdi hdk hdm hdo; do hdparm -tT /dev/$i; done
> > >
> > > /dev/hdi:
> > > Timing buffer-cache reads: 128 MB in 0.70 seconds =182.86 MB/sec
> > > Timing buffered disk reads: 64 MB in 2.03 seconds = 31.53 MB/sec
> > >
> > > /dev/hdk:
> > > Timing buffer-cache reads: 128 MB in 0.69 seconds =185.51 MB/sec
> > > Timing buffered disk reads: 64 MB in 2.03 seconds = 31.53 MB/sec
> > >
> > > /dev/hdm:
> > > dies here.....
> > >
> > > Shawn
> > >
> >
> > Cheers,
> > hp
> > -
> > To unsubscribe from this list: send the line "unsubscribe linux-raid" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2005-03-22 13:32    [W:0.087 / U:0.564 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site