Messages in this thread | | | Date | 31 Jan 2003 18:46:05 -0000 | From | "saurabh khanna" <> |
| |
Problem: My xwindows did not open and my sound card don't work.
Xwindows: I am a novice. I am using redhat linux 8. It detects my graphics card correctly but when i tried to open xwindows, my system hangs.
Sound: Linux has detected my sound card once but not configured it and after that nor it is working nither it is detected by my linux.
GRUB: Also, i can boot my linux through LILO only. GRUB wont work, it gives error "Not enough memory".
I have re-installed linux on my computer but the problem remains. All other detailes are follows.
Kernel version: Linux version 2.4.18-14 (bhcompile@astest.test.redhat.com) (gcc version 3.2 20020903 (Red Hat Linux 8.0 3.2-7)) #1 Wed Sep 4 12:13:11 EDT 2002
Commond which triggers the problem: startx
Processor information: processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(TM) XP 1700+
stepping : 2
cpu MHz : 1469.861
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 2920.57
Module information: nls_iso8859-1 3516 1 (autoclean)
nls_cp437 5116 1 (autoclean)
vfat 13084 1 (autoclean)
fat 38744 0 (autoclean) [vfat] autofs 13348 0 (autoclean) (unused)
ipt_REJECT 3736 2 (autoclean)
iptable_filter 2412 1 (autoclean)
ip_tables 14840 2 [ipt_REJECT iptable_filter]
mousedev 5524 0 (unused)
keybdev 2976 0 (unused)
hid 22244 0 (unused)
input 5888 0 [mousedev keybdev hid]
usb-ohci 21288 0 (unused)
usbcore 77056 1 [hid usb-ohci]
ext3 70400 1
jbd 52212 1 [ext3]
Loaded driver and hardware information: 0000-001f : dma 1 0020-003f : pic 1 0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic 2 00c0-00df : dma 2 00f0-00ff : fpu
01f0-01f7 : ide 0 02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide 0 03f8-03ff : serial(auto)
0cf8-0cff : PCI conf 1 5000-500f : PCI device 10de:01b4 (nVidia Corporation)
5100-511f : PCI device 10de:01b4 (nVidia Corporation)
5500-550f : PCI device 10de:01b4 (nVidia Corporation)
a800-a80f : nVidia Corporation nForce IDE
a800-a807 : ide0
a808-a80f : ide1
b000-bfff : PCI Bus #01
b800-b807 : Rockwell International HCF 56k Data/Fax/Voice/Spkp (w/Handset) Modem
d800-d807 : PCI device 10de:01c3 (nVidia Corporation)
e000-e07f : PCI device 10de:01b1 (nVidia Corporation)
e100-e1ff : PCI device 10de:01b1 (nVidia Corporation)
00000000-0007ffff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-06febfff : System RAM
00100000-00247f2e : Kernel code
00247f2f-0033ed03 : Kernel data
06fec000-06feefff : ACPI Tables
06fef000-06ffefff : reserved
06fff000-06ffffff : ACPI Non-volatile Storage
eb000000-ec7fffff : PCI Bus #02
eb000000-ebffffff : nVidia Corporation GeForce2 Integrated GPU
ec800000-ecffffff : PCI Bus #01
ec800000-ec80ffff : Rockwell International HCF 56k Data/Fax/Voice/Spkp (w/Handset) Modem
ed000000-ed000fff : PCI device 10de:01b1 (nVidia Corporation)
ed800000-ed87ffff : PCI device 10de:01b0 (nVidia Corporation)
ee000000-ee0003ff : PCI device 10de:01c3 (nVidia Corporation)
ee800000-ee800fff : PCI device 10de:01c2 (nVidia Corporation)
ee800000-ee800fff : usb-ohci e f000000-ef000fff : PCI device 10de:01c2 (nVidia Corporation)
ef000000-ef000fff : usb-ohci e ff00000-f7ffffff : PCI Bus #02
f0000000-f7ffffff : nVidia Corporation GeForce2 Integrated GPU
f8000000-fbffffff : PCI device 10de:01a4 (nVidia Corporation)
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
PCI information: 00:00.0 Host bridge: nVidia Corporation nForce CPU bridge (rev b2) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: [40] AGP version 2.0 Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x1 Capabilities: [60] #08 [2001]
00:00.1 RAM memory: nVidia Corporation nForce 220/420 Memory Controller (rev b2) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.2 RAM memory: nVidia Corporation nForce 220/420 Memory Controller (rev b2) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation: Unknown device 01aa (rev b2) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.0 ISA bridge: nVidia Corporation nForce ISA Bridge (rev c3) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [50] #08 [01e1]
00:01.1 SMBus: nVidia Corporation nForce PCI System Management (rev c1) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 5000 [size=16] Region 1: I/O ports at 5500 [size=16] Region 2: I/O ports at 5100 [size=32] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation: Unknown device 01c2 (rev c3) (prog-if 10 [OHCI]) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at ef000000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller: nVidia Corporation: Unknown device 01c2 (rev c3) (prog-if 10 [OHCI]) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at ee800000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: nVidia Corporation: Unknown device 01c3 (rev c2) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=1K] Region 1: I/O ports at d800 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: nVidia Corporation: Unknown device 01b0 (rev c2) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (250ns min, 3000ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at ed800000 (32-bit, non-prefetchable) [size=512K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: nVidia Corporation nForce Audio (rev c2) Subsystem: nVidia Corporation: Unknown device 8384 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at e100 [size=256] Region 1: I/O ports at e000 [size=128] Region 2: Memory at ed000000 (32-bit, non-prefetchable) [disabled] [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 PCI bridge: nVidia Corporation nForce PCI-to-PCI bridge (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: ec800000-ecffffff Prefetchable memory behind bridge: f8000000-f7ffffff BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:09.0 IDE interface: nVidia Corporation nForce IDE (rev c3) (prog-if 8a [Master SecP PriP]) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Region 4: I/O ports at a800 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: nVidia Corporation nForce AGP to PCI Bridge (rev b2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=64 I/O behind bridge: 0000a000-00009fff Memory behind bridge: eb000000-ec7fffff Prefetchable memory behind bridge: eff00000-f7ffffff BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
01:08.0 Communication controller: Rockwell International HCF 56k Data/Fax/Voice/Spkp (w/Handset) Modem (rev 01) Subsystem: Rockwell International HCF 56k Data/Fax/Voice/Spkp (w/Handset) Modem Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 5 Region 0: Memory at ec800000 (32-bit, non-prefetchable) [size=64K] Region 1: I/O ports at b800 [size=8] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
02:00.0 VGA compatible controller: nVidia Corporation NV15 [GeForce2 - nForce GPU] (rev b1) (prog-if 00 [VGA]) Subsystem: nVidia Corporation: Unknown device 0c11 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 11 Region 0: Memory at eb000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M] Expansion ROM at efff0000 [disabled] [size=64K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 2.0 Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x4 Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
XF86Config:
# File generated by anaconda.
Section "ServerLayout" Identifier "Anaconda Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Mouse1" "SendCoreEvents" InputDevice "Keyboard0" "CoreKeyboard" EndSection
Section "Files"
# The location of the RGB database. Note, this is the name of the # file minus the extension (like ".txt" or ".db"). There is normally # no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (they are concatenated together) # By default, Red Hat 6.0 and later now use a font server independent of # the X server to render fonts.
FontPath "unix/:7100"
EndSection
Section "Module" Load "dbe" Load "extmod" Load "fbdevhw" Load "dri" Load "glx" Load "record" Load "freetype" Load "type1" EndSection
Section "InputDevice" Identifier "Keyboard0" Driver "keyboard"
# Option "AutoRepeat" "500 5"
# when using XQUEUE, comment out the above line, and uncomment the # following line # Option "Protocol" "Xqueue"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable. # Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc102" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: # Option "XkbOptions" "ctrl:swapcaps" Option "XkbRules" "xfree86" Option "XkbModel" "pc105" Option "XkbLayout" "us" #Option "XkbVariant" "" #Option "XkbOptions" "" EndSection
Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "PS/2" Option "Device" "/dev/psaux" Option "ZAxisMapping" "4 5" Option "Emulate3Buttons" "yes" EndSection
Section "InputDevice" Identifier "Mouse1" Driver "mouse" Option "Device" "/dev/input/mice" Option "Protocol" "IMPS/2" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection
Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" HorizSync 30-55 VertRefresh 50-120 Option "dpms"
EndSection
Section "Device" # no known options Identifier "NVIDIA GeForce 2 MX (generic)" Driver "nv" VendorName "NVIDIA GeForce 2 MX (generic)" BoardName "NVIDIA GeForce 2 MX (generic)"
#BusID EndSection
Section "Screen" Identifier "Screen0" Device "NVIDIA GeForce 2 MX (generic)" Monitor "Monitor0" DefaultDepth 16
Subsection "Display" Depth 16 Modes "1024x768" "800x600" "640x480" EndSubsection
EndSection
Section "DRI" Mode 0666 EndSection
cmdline: auto BOOT_IMAGE=linux ro BOOT_FILE=/boot/vmlinuz-2.4.18-14 root=LABEL=/
dma: 4: cascade
intrrupts: CPU0 0: 337647 XT-PIC timer 1: 2694 XT-PIC keyboard 2: 0 XT-PIC cascade 5: 0 XT-PIC usb-ohci, usb-ohci 8: 1 XT-PIC rtc 12: 20 XT-PIC PS/2 Mouse 14: 27338 XT-PIC ide0 NMI: 0 ERR: 2
partitions: major minor #blocks name rio rmerge rsect ruse wio wmerge wsect wuse running use aveq
3 0 39121488 hda 2567 4181 52107 22201 1417 1941 26952 45880 -2 329576 7788488 3 1 5245191 hda1 9 43 104 109 0 0 0 0 0 109 109 3 2 1 hda2 0 0 0 0 0 0 0 0 0 0 0 3 5 10490413 hda5 9 43 104 95 0 0 0 0 0 95 95 3 6 11695288 hda6 50 43 145 214 7 1 8 95 0 230 310 3 7 8104761 hda7 9 43 104 132 0 0 0 0 0 132 132 3 8 3277228 hda8 2475 3966 51498 21527 1410 1940 26944 45785 0 22394 67314 3 9 305203 hda9 9 25 104 56 0 0 0 0 0 56 56
My e-mail addresses are: linux_guyus@yahoo.com and linux_guyus@rediff.com My postel address: 80, Ahilya Nagar Ext. Annapurna Road, Indore, M.P., India. PIN 452009 please answer me soon. Thanking you. Saurabh Khanna.
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |