Messages in this thread | | | Date | Fri, 30 Aug 2002 21:01:46 -0400 | From | Olivier Galibert <> | Subject | 2.4.20-pre5-ac1 PDC20269 80-pin acble misdetection |
| |
All the cables in my system are 80-pin. On that card, one is standard and the other rounded. There is only one disk per channel, which may explain the misdetection.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha1 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PDC20269: IDE controller at PCI slot 00:10.0 PCI: Found IRQ 9 for device 00:10.0 PCI: Sharing IRQ 9 with 00:09.0 PDC20269: chipset revision 2 PDC20269: not 100% native mode: will probe irqs later ide2: BM-DMA at 0x9000-0x9007, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0x9008-0x900f, BIOS settings: hdg:pio, hdh:pio VP_IDE: IDE controller at PCI slot 00:11.1 PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using pci=biosirq. VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci00:11.1 ide0: BM-DMA at 0x8800-0x8807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8808-0x880f, BIOS settings: hdc:DMA, hdd:DMA hda: Maxtor 98196H8, ATA DISK drive hdc: CREATIVE CD-RW RW1210E, ATAPI CD/DVD-ROM drive hdd: PIONEER DVD-RW DVR-104, ATAPI CD/DVD-ROM drive hde: Maxtor 4G160J8, ATA DISK drive ULTRA 66/100/133: Primary channel of Ultra 66/100/133 requires an 80-pin cable for Ultra66 operation. Switching to Ultra33 mode. Warning: Primary channel requires an 80-pin cable for operation. hde reduced to Ultra33 mode. hdg: Maxtor 4G160J8, ATA DISK drive ULTRA 66/100/133: Secondary channel of Ultra 66/100/133 requires an 80-pin cable for Ultra66 operation. Switching to Ultra33 mode. Warning: Secondary channel requires an 80-pin cable for operation. hdg reduced to Ultra33 mode. ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide2 at 0xa400-0xa407,0xa002 on irq 9 ide3 at 0x9800-0x9807,0x9402 on irq 9 hda: host protected area => 1 hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=9964/255/63, UDMA(100) hde: host protected area => 1 hde: 320173056 sectors (163929 MB) w/2048KiB Cache, CHS=19929/255/63, UDMA(133) hdg: host protected area => 1 hdg: 320173056 sectors (163929 MB) w/2048KiB Cache, CHS=19929/255/63, UDMA(133) hdc: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.12 hdd: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33) Partition check: hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hde: hde1 hdg: hdg1
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266] Subsystem: Asustek Computer, Inc.: Unknown device 807f Flags: bus master, 66Mhz, medium devsel, latency 0 Memory at e0000000 (32-bit, prefetchable) [size=256M] Capabilities: <available only to root>
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode]) Flags: bus master, 66Mhz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: d6000000-d75fffff Prefetchable memory behind bridge: d7700000-dfffffff Capabilities: <available only to root>
00:10.0 Unknown mass storage controller: Promise Technology, Inc.: Unknown device 4d69 (rev 02) (prog-if 85) Subsystem: Promise Technology, Inc.: Unknown device 4d68 Flags: bus master, 66Mhz, slow devsel, latency 32, IRQ 9 I/O ports at a400 [size=8] I/O ports at a000 [size=4] I/O ports at 9800 [size=8] I/O ports at 9400 [size=4] I/O ports at 9000 [size=16] Memory at d3000000 (32-bit, non-prefetchable) [size=16K] Expansion ROM at <unassigned> [disabled] [size=16K] Capabilities: <available only to root>
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Asustek Computer, Inc.: Unknown device 808c Flags: bus master, medium devsel, latency 32 I/O ports at 8800 [size=16] Capabilities: <available only to root>
/dev/hda:
Model=aMtxro9 18698H , FwRev=AZ8H410Y, SerialNo=8V30F3CE Config={ Fixed } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57 BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=160086528 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 AdvancedPM=yes: disabled (255) Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
/dev/hde:
Model=Maxtor 4G160J8, FwRev=DAK019K0, SerialNo=G8000000 Config={ Fixed } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57 BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=268435455 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 AdvancedPM=yes: disabled (255) Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
/dev/hdg:
Model=aMtxro4 1G068J , FwRev=AG8KC10K, SerialNo=8GB0VPE2 Config={ Fixed } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57 BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16 CurCHS=65535/1/63, CurSects=-4128706, LBA=yes, LBAsects=268435455 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 AdvancedPM=yes: disabled (255) Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6
I can test things as needed, that computer is horribly unstable anyway...
OG. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |