Messages in this thread |  | | From | brian@worldcon ... | Date | Fri, 30 Aug 2002 13:27:15 -0700 | Subject | Re: My /dev/hda became /dev/hde after upgrading |
| |
On Wed, Aug 28, 2002 at 11:23:36PM -0700, Andre Hedrick wrote: > > For now issue in your append line "ide=reverse". > This will get you by until it can be fixed.
Thanks, that worked.
An interesting note. While things were running backwards, that is on /dev/hde the filesystem was very slow. An operation that generally ran in about 5 seconds took about a minute. A large filesystem backup, generally taking about 5 minutes, took about 45 minutes.
As of reversing things back (/dev/hda) speed is back to normal.
The system only seemed slowed on disk access.
> On Wed, 28 Aug 2002 brian@worldcontrol.com wrote: > > > While running 2.4.19-pre7-ac2 my system was happily buzzing away. > > > > I upgraded to 2.4.19 and my /dev/hda became /dev/hde which caused > > various boot problems, which I worked around. > > > > It seems clear that upon booting 2.4.19, the newer kernel recognized > > the "other" IDE controller on the MB, which 2.4.19-pre7-ac2 had not. > > > > The manual that came with the MB said to use the IDE slots marked > > IDE0 / IDE1 if I wasn't going to use RAID. > > > > If I wanted to use RAID use the slots marked RAID0/RAID1. > > > > I was just wondering how linux decides which controller is first > > (hda-hdd) and which is second (hde-hdh). > > > > Here is what I see from dmesg: > > > > Uniform Multi-Platform E-IDE driver Revision: 6.31 > > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > > PDC20265: IDE controller on PCI bus 00 dev 70 > > PDC20265: chipset revision 2 > > PDC20265: not 100% native mode: will probe irqs later > > ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:pio, hdb:DMA > > ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio > > VP_IDE: IDE controller on PCI bus 00 dev 89 > > PCI: No IRQ known for interrupt pin A of device 00:11.1. Please try using pci=bi > > osirq. > > VP_IDE: chipset revision 6 > > VP_IDE: not 100% native mode: will probe irqs later > > VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci00:11.1 > > ide2: BM-DMA at 0xb800-0xb807, BIOS settings: hde:DMA, hdf:pio > > ide3: BM-DMA at 0xb808-0xb80f, BIOS settings: hdg:DMA, hdh:pio > > hde: ST380021A, ATA DISK drive > > hdg: RW-241040, ATAPI CD/DVD-ROM drive > > ide2 at 0x1f0-0x1f7,0x3f6 on irq 14 > > ide3 at 0x170-0x177,0x376 on irq 15 > > hde: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100) > > Partition check: > > hde: hde1 hde2 < hde5 hde6 > > > > > -- > > Brian Litzinger > > - > > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > > the body of a message to majordomo@vger.kernel.org > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > Please read the FAQ at http://www.tux.org/lkml/ > > > > Andre Hedrick > LAD Storage Consulting Group
-- Brian Litzinger - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
|  |